2005 MERCEDES-BENZ SPRINTER mirror

NOTE: Use mineral spirits as a lubricant to aid seal
installation in the window opening.
(3) Position the glass and seal in the window open-
ing.
(4) Pull the installation cord outward and force the
seal lip over the panel flange around the edge of the
opening.
(5) Seat the seal inner lip on the panel flange.
Press against the lip around the edge of the seal.
NOTE: Remove any mineral spirits with a clean
cloth after glass installation.
(6) Verify that the seal is seated in the window
opening (Fig. 2).
(7) Test the window for water leaks. (Refer to 23 -
BODY - DIAGNOSIS AND TESTING - WATER
LEAKS)
WINDSHIELD
WARNING
WINDSHIELD SAFETY PRECAUTIONS
WARNING: DO NOT OPERATE THE VEHICLE
WITHIN 24 HOURS OF WINDSHIELD INSTALLATION.IT TAKES AT LEAST 24 HOURS FOR URETHANE
ADHESIVE TO CURE. IF IT IS NOT CURED, THE
WINDSHIELD MAY NOT PERFORM PROPERLY IN
AN ACCIDENT.
²URETHANE ADHESIVES ARE APPLIED AS A
SYSTEM. USE GLASS CLEANER, GLASS PREP
SOLVENT, GLASS PRIMER, PVC (VINYL) PRIMER
AND PINCH WELD (FENCE) PRIMER PROVIDED BY
THE ADHESIVE MANUFACTURER. IF NOT, STRUC-
TURAL INTEGRITY COULD BE COMPROMISED.
²DAIMLERCHRYSLER DOES NOT RECOMMEND
GLASS ADHESIVE BY BRAND. TECHNICIANS
SHOULD REVIEW PRODUCT LABELS AND TECHNI-
CAL DATA SHEETS, AND USE ONLY ADHESIVES
THAT THEIR MANUFACTURES WARRANT WILL
RESTORE A VEHICLE TO THE REQUIREMENTS OF
FMVSS 212. TECHNICIANS SHOULD ALSO INSURE
THAT PRIMERS AND CLEANERS ARE COMPATIBLE
WITH THE PARTICULAR ADHESIVE USED.
²BE SURE TO REFER TO THE URETHANE MAN-
UFACTURER'S DIRECTIONS FOR CURING TIME
SPECIFICATIONS, AND DO NOT USE ADHESIVE
AFTER ITS EXPIRATION DATE.
²VAPORS THAT ARE EMITTED FROM THE URE-
THANE ADHESIVE OR PRIMER COULD CAUSE
PERSONAL INJURY. USE THEM IN A WELL-VENTI-
LATED AREA.
²SKIN CONTACT WITH URETHANE ADHESIVE
SHOULD BE AVOIDED. PERSONAL INJURY MAY
RESULT.
²ALWAYS WEAR EYE AND HAND PROTECTION
WHEN WORKING WITH GLASS.
CAUTION: Protect all painted and trimmed surfaces
from coming in contact with urethane or primers.
Be careful not to damage painted surfaces when
removing moldings or cutting urethane around
windshield.
REMOVAL
(1) Remove wiper arms. (Refer to 8 - ELECTRI-
CAL/WIPERS/WASHERS/WIPER ARMS -
REMOVAL)
(2) Remove headliner. (Refer to 23 - BODY/INTE-
RIOR/HEADLINER - REMOVAL)
(3) Remove rear view mirror. (Refer to 23 - BODY/
INTERIOR/REAR VIEW MIRROR - REMOVAL)
CAUTION: Cover instrument panel and vents to pro-
tect against splinters and damage.
Fig. 2 Glass & Weatherstrip Seal Installation
1 - BODY PANEL
2 - WEATHERSTRIP SEAL
3 - INSTALLATION CORD
4 - WINDOW OPENING
23 - 82 STATIONARY GLASSVA
QUARTER WINDOW (Continued)

(2) Allow end of adhesive bead to run out parallel
to the start of the bead and smooth ends flush. (Fig.
13)
(3) Lift windshield into place in the center of the
windshield opening and use the tape as a guide toaid installation of the windshield into the center of
the cutout.
(4) Carefully lay down windshield and press on.
CAUTION: It is no longer possible to move the
windshield after installation. The windshield should
never be pressed into place by more than one per-
son, because the windshield can break if pressed
simultaneously on both sides.
CAUTION: Roll down the left and right front door
glass and open the rear glass slider (if available)
before installing windshield to avoid pressurizing
the passenger compartment if a door is slammed
before urethane is cured. Water leaks can result.
(1) Install the rear view mirror. (Refer to 23 -
BODY/INTERIOR/REAR VIEW MIRROR - INSTAL-
LATION)
(2) Install the headliner. (Refer to 23 - BODY/IN-
TERIOR/HEADLINER - INSTALLATION)
(3) Install the wiper arms. (Refer to 8 - ELECTRI-
CAL/WIPERS/WASHERS/WIPER ARMS - INSTAL-
LATION)
Fig. 13 WINDSHIELD ADHESIVE OVERLAP
1 - ADHESIVE BEAD
2 - WINDSHIELD SEAL
23 - 86 STATIONARY GLASSVA
WINDSHIELD (Continued)

BACKLITE - BULKHEAD TRIM PANEL -
INSTALLATION.......................23-81
BACKLITE - BULKHEAD TRIM PANEL -
REMOVAL..........................23-81
BACKUP LAMP BULB - INSTALLATION.....8L-6
BACKUP LAMP BULB - REMOVAL........8L-5
BALANCE - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-3
BALL JOINT - INSTALLATION, LOWER......2-6
BALL JOINT - REMOVAL, LOWER..........2-6
BAR - DESCRIPTION, STABILIZER.........2-9
BAR - INSTALLATION, STABILIZER.....2-15,2-9
BAR - OPERATION, STABILIZER...........2-9
BAR - REMOVAL, STABILIZER........2-15,2-9
BASE BRAKE, SPECIFICATIONS............5-6
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-2
BASECOAT/CLEARCOAT FINISH -
DESCRIPTION.......................23-74
BATTERY - DESCRIPTION...............8F-6
BATTERY - DIAGNOSIS AND TESTING.....8F-7
BATTERY - OPERATION.................8F-7
BATTERY CABLES - DESCRIPTION.......8F-14
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-14
BATTERY CABLES - INSTALLATION.......8F-16
BATTERY CABLES - OPERATION.........8F-14
BATTERY CABLES - REMOVAL..........8F-16
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY ELECTROLYTE LEVEL -
STANDARD PROCEDURE, CHECKING.....8F-12
BATTERY HOLDDOWN - DESCRIPTION....8F-14
BATTERY HOLDDOWN - INSTALLATION . . . 8F-14
BATTERY HOLDDOWN - REMOVAL.......8F-14
BATTERY INSTALLATION, INSTALLATION
- AUXILIARY........................8F-13
BATTERY INSTALLATION, INSTALLATION
- UNDER HOOD......................8F-13
BATTERY REMOVAL, REMOVAL -
AUXILIARY..........................8F-13
BATTERY REMOVAL, REMOVAL - UNDER
HOOD..............................8F-12
BATTERY SYSTEM - CLEANING...........8F-5
BATTERY SYSTEM - DESCRIPTION........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING............................8F-2
BATTERY SYSTEM - INSPECTION.........8F-6
BATTERY SYSTEM - OPERATION.........8F-2
BATTERY SYSTEM SPECIAL TOOLS,
SPECIAL TOOLS......................8F-6
BATTERY TESTER - STANDARD
PROCEDURE, USING MICRO 420........8F-11
BATTERY TRAY - DESCRIPTION.........8F-16
BATTERY TRAY - INSTALLATION.........8F-16
BATTERY TRAY - OPERATION...........8F-16
BATTERY TRAY - REMOVAL............8F-16
BEAM HEADLAMP BULB -
INSTALLATION, HIGH.................8L-17
BEAM HEADLAMP BULB -
INSTALLATION, LOW..................8L-19
BEAM HEADLAMP BULB - REMOVAL,
HIGH..............................8L-17
BEAM HEADLAMP BULB - REMOVAL,
LOW ..............................8L-18
BEAM INDICATOR - DESCRIPTION, HIGH . . 8J-17
BEAM INDICATOR - OPERATION, HIGH....8J-17
BEARING - INSTALLATION, CENTER........3-9
BEARING - INSTALLATION, HUB...........2-5
BEARING - INSTALLATION, OUTPUT
SHAFT............................21-122
BEARING - REMOVAL, CENTER...........3-8
BEARING - REMOVAL, HUB..............2-4
BEARING - REMOVAL, OUTPUT SHAFT . . . 21-122
BEARINGS/SEALS - INSTALLATION, AXLE . . 3-17
BEARINGS/SEALS - INSTALLATION, AXLE
HUB................................3-20
BEARINGS/SEALS - REMOVAL, AXLE......3-17
BEARINGS/SEALS - REMOVAL, AXLE
HUB
................................3-20
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE
.....................7-5
BELT & RETRACTOR - INSTALLATION,
FRONT SEAT
........................8O-21
BELT & RETRACTOR - INSTALLATION,
REAR SEAT
.........................8O-29
BELT & RETRACTOR - REMOVAL, FRONT
SEAT
..............................8O-19BELT & RETRACTOR - REMOVAL, REAR
SEAT ..............................8O-27
BELT BUCKLE - INSTALLATION, FRONT
SEAT ..............................8O-23
BELT BUCKLE - REMOVAL, FRONT SEAT . . 8O-22
BELT SWITCH - DESCRIPTION, SEAT.....8O-31
BELT SWITCH - OPERATION, SEAT.......8O-31
BELT TENSIONER - DESCRIPTION, SEAT . . 8O-31
BELT TENSIONER - OPERATION, SEAT....8O-32
BELT TENSIONERS - DESCRIPTION........7-5
BELT TENSIONERS - OPERATION..........7-5
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT.................8O-34
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT.....................8O-33
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR INNER..................23-87
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR OUTER.................23-87
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR INNER..................23-87
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR OUTER.................23-87
BELTS - INSTALLATION, DRIVE............7-8
BELTS - REMOVAL, DRIVE...............7-8
BEZEL - INSTALLATION, ACCESSORY
SWITCH............................23-54
BEZEL - INSTALLATION, CLUSTER.......23-54
BEZEL - INSTALLATION, INSTRUMENT
PANEL CENTER......................23-55
BEZEL - REMOVAL, ACCESSORY SWITCH . 23-54
BEZEL - REMOVAL, CLUSTER...........23-53
BEZEL - REMOVAL, INSTRUMENT PANEL
CENTER............................23-55
BLADE - DESCRIPTION, WIPER.........8R-15
BLADE - INSTALLATION, WIPER.........8R-16
BLADE - OPERATION, WIPER...........8R-15
BLADE - REMOVAL, WIPER............8R-16
BLEED PROCEDURE, STANDARD
PROCEDURE - POWER STEERING
PUMP FILL.........................19-14
BLEEDING - STANDARD PROCEDURE,
MANUAL.............................5-4
BLEEDING - STANDARD PROCEDURE,
MASTER CYLINDER...................5-17
BLEEDING - STANDARD PROCEDURE,
PRESSURE...........................5-5
BLOCK - DESCRIPTION, BLOWER
MOTOR RESISTOR...................24-16
BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR............24-16
BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR...................24-17
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR..........................24-16
BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR..........................24-16
BLOCK #1 - DESCRIPTION, FUSE......8W-97-2
BLOCK #1 - INSTALLATION, FUSE.....8W-97-3
BLOCK #1 - OPERATION, FUSE.......8W-97-2
BLOCK #1 - REMOVAL, FUSE.........8W-97-3
BLOCK #2 - DESCRIPTION, FUSE......8W-97-3
BLOCK #2 - OPERATION, FUSE.......8W-97-3
BLOCK HEATER - INSTALLATION,
ENGINE.............................7-14
BLOCK HEATER - REMOVAL, ENGINE......7-14
BLOCK JOURNALS - STANDARD
PROCEDURE, MEASURE CRANKSHAFT
....9-35
BLOWER MOTOR - INSTALLATION
. . 24-33,24-40
BLOWER MOTOR - REMOVAL
......24-32,24-39
BLOWER MOTOR RELAY - DESCRIPTION
. . 24-23
BLOWER MOTOR RELAY - DIAGNOSIS
AND TESTING
.......................24-24
BLOWER MOTOR RELAY -
INSTALLATION
.......................24-24
BLOWER MOTOR RELAY - OPERATION
. . . 24-23
BLOWER MOTOR RELAY - REMOVAL
.....24-24
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION
.......................24-16
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING
.............24-16
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION
.......................24-17
BLOWER MOTOR RESISTOR BLOCK -
OPERATION
.........................24-16
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL
..........................24-16BLOWER MOTOR SWITCH -
DESCRIPTION..................24-17,24-22
BLOWER MOTOR SWITCH - DIAGNOSIS
AND TESTING..................24-17,24-23
BLOWER MOTOR SWITCH -
INSTALLATION.......................24-23
BLOWER MOTOR SWITCH - OPERATION . . 24-17,
24-22
BLOWER MOTOR SWITCH - REMOVAL . . . 24-17,
24-23
BODY & CABLE - INSTALLATION,
ANTENNA...........................8A-1
BODY & CABLE - REMOVAL, ANTENNA....8A-1
BODY PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC.................23-3
BOLT INSPECTION - STANDARD
PROCEDURE, CYLINDER HEAD...........9-21
BOOST PRESSURE SENSOR -
DESCRIPTION.......................14-17
BOOST PRESSURE SENSOR -
DIAGNOSIS AND TESTING.............14-18
BOOST PRESSURE SENSOR -
INSTALLATION.......................14-18
BOOST PRESSURE SENSOR -
OPERATION.........................14-18
BOOST PRESSURE SENSOR - REMOVAL . . 14-18
BOOSTER - DESCRIPTION, POWER
BRAKE..............................5-19
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-16
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-19
BOOSTER - OPERATION, POWER BRAKE....5-19
BOOSTER - REMOVAL, POWER BRAKE....5-19
BORES - STANDARD PROCEDURE,
MEASURING CYLINDER................9-34
BOX - INSTALLATION, GLOVE...........23-56
BOX - REMOVAL, GLOVE..............23-56
B-PILLAR TRIM - INSTALLATION........23-69
B-PILLAR TRIM - REMOVAL............23-68
BRACKET - INSTALLATION, LICENSE
PLATE .............................23-47
BRACKET - INSTALLATION, PASSENGER
AIRBAG............................8O-27
BRACKET - INSTALLATION, REAR VIEW
MIRROR SUPPORT...................23-72
BRACKET - REMOVAL, LICENSE PLATE . . . 23-47
BRACKET - REMOVAL, PASSENGER
AIRBAG............................8O-27
BRAKE - CLEANING, REAR DRUM IN
HAT ................................5-27
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK...........................8E-3
BRAKE - REMOVAL, CONTROLLER
ANTILOCK...........................8E-3
BRAKE BOOSTER - DESCRIPTION,
POWER.............................5-19
BRAKE BOOSTER - INSTALLATION,
POWER.............................5-19
BRAKE BOOSTER - OPERATION, POWER . . . 5-19
BRAKE BOOSTER - REMOVAL, POWER....5-19
BRAKE CABLES - ADJUSTMENT,
PARKING............................5-25
BRAKE FLUID - DESCRIPTION............0-3
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-14
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-14
BRAKE FLUID, SPECIFICATIONS..........5-14
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-11
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-12
BRAKE LAMP SWITCH - INSTALLATION....8L-6
BRAKE LAMP SWITCH - REMOVAL.......8L-6
BRAKE, SPECIAL TOOLS - PARK.........5-23
BRAKE, SPECIFICATIONS - BASE..........5-6
BRAKE SWITCH - INSTALLATION, PARK . . . 8L-20
BRAKE SWITCH - REMOVAL, PARK
......8L-20
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE
........................5-2
BRAKE WEAR INDICATOR -
DESCRIPTION
.......................8J-12
BRAKE WEAR INDICATOR - OPERATION
. . . 8J-12
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION
.......................8J-11
2 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

FREEWHEELING CLUTCH -
DISASSEMBLY......................21-106
FREEWHEELING CLUTCH - OPERATION . . 21-105
FROM FUEL FILTER - STANDARD
PROCEDURES, DRAINING WATER........14-2
FROM GEAR TO COOLER TUBE -
INSTALLATION, RETURN HOSE..........19-15
FROM GEAR TO COOLER TUBE -
REMOVAL, RETURN HOSE.............19-15
FROM PUMP TO COOLER TUBE -
INSTALLATION, RETURN LINE..........19-15
FROM PUMP TO COOLER TUBE -
REMOVAL, RETURN LINE..............19-15
FRONT - INSTALLATION............5-14,5-24
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-38
FRONT - INSTALLATION, SEAT..........23-77
FRONT - INSTALLATION, SEAT
ADJUSTERS.........................23-78
FRONT - INSTALLATION, SEAT BACK.....23-77
FRONT - INSTALLATION, SEAT CUSHION . . 23-78
FRONT - REMOVAL................5-13,5-24
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-38
FRONT - REMOVAL, SEAT..............23-77
FRONT - REMOVAL, SEAT ADJUSTERS . . . 23-78
FRONT - REMOVAL, SEAT BACK.........23-77
FRONT - REMOVAL, SEAT CUSHION......23-78
FRONT BUMPER - STEPS -
INSTALLATION........................13-2
FRONT BUMPER - STEPS - REMOVAL.....13-2
FRONT COVER - INSTALLATION,
CYLINDER HEAD......................9-26
FRONT COVER - REMOVAL, CYLINDER
HEAD...............................9-23
FRONT DOOR INNER BELT
WEATHERSTRIP - INSTALLATION........23-87
FRONT DOOR INNER BELT
WEATHERSTRIP - REMOVAL............23-87
FRONT DOOR OUTER BELT
WEATHERSTRIP - INSTALLATION........23-87
FRONT DOOR OUTER BELT
WEATHERSTRIP - REMOVAL............23-87
FRONT (DRW) - INSTALLATION . . 5-11,5-13,5-21
FRONT (DRW) - REMOVAL.......5-12,5-20,5-9
FRONT FASCIA - INSTALLATION..........13-2
FRONT FASCIA - REMOVAL..............13-2
FRONT LAMP UNIT - ADJUSTMENT......8L-12
FRONT LAMP UNIT - INSTALLATION.....8L-12
FRONT LAMP UNIT - REMOVAL.........8L-12
FRONT POSITION LAMP BULB -
INSTALLATION.......................8L-14
FRONT POSITION LAMP BULB -
REMOVAL..........................8L-14
FRONT SEAT BELT & RETRACTOR -
INSTALLATION......................8O-21
FRONT SEAT BELT & RETRACTOR -
REMOVAL..........................8O-19
FRONT SEAT BELT BUCKLE -
INSTALLATION......................8O-23
FRONT SEAT BELT BUCKLE - REMOVAL . . 8O-22
FRONT (SRW) - INSTALLATION . . 5-10,5-12,5-21
FRONT (SRW) - REMOVAL.......5-11,5-19,5-9
FRONT SUSPENSION, SPECIAL TOOLS....19-11
FRONT SUSPENSION, SPECIAL TOOLS.....2-2
FRONT TURN/PARK/SIDE MARKER LAMP
BULB - INSTALLATION................8L-15
FRONT TURN/PARK/SIDE MARKER LAMP
BULB - REMOVAL....................8L-14
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-30
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-30
FUEL DOSING PUMP - DESCRIPTION.....24-74
FUEL DOSING PUMP - INSTALLATION....24-74
FUEL DOSING PUMP - OPERATION......24-74
FUEL DOSING PUMP - REMOVAL........24-74
FUEL FILL DOOR - INSTALLATION.......23-47
FUEL FILL DOOR - REMOVAL...........23-47
FUEL FILTER - DESCRIPTION............14-5
FUEL FILTER - INSTALLATION
............14-6
FUEL FILTER - OPERATION
..............14-5
FUEL FILTER - REMOVAL
...............14-5
FUEL FILTER - STANDARD
PROCEDURES, DRAINING WATER
FROM
..............................14-2
FUEL FILTER CLOGGED INDICATOR -
DESCRIPTION
.......................8J-15FUEL FILTER CLOGGED INDICATOR -
OPERATION.........................8J-15
FUEL GAUGE - DESCRIPTION...........8J-16
FUEL GAUGE - OPERATION.............8J-16
FUEL INDICATOR - DESCRIPTION, LOW . . . 8J-18
FUEL INDICATOR - OPERATION, LOW.....8J-18
FUEL INJECTOR, DESCRIPTION.........14-20
FUEL INJECTORS - STANDARD
PROCEDURE, CLEANING...............14-22
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION.......................14-15
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION.......................14-15
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL..........................14-15
FUEL LINE - INSTALLATION............24-76
FUEL LINE - REMOVAL................24-75
FUEL LINES - DIAGNOSIS AND TESTING,
HIGH PRESSURE......................14-1
FUEL LINES - STANDARD PROCEDURE,
DISCONNECTING AND CONNECTING......14-2
FUEL PRESSURE SOLENOID -
DESCRIPTION.......................14-27
FUEL PRESSURE SOLENOID -
INSTALLATION.......................14-28
FUEL PRESSURE SOLENOID -
OPERATION.........................14-27
FUEL PRESSURE SOLENOID - REMOVAL . . 14-28
FUEL PUMP TEST - STANDARD
PROCEDURE, LOW PRESSURE...........14-3
FUEL RAIL - DESCRIPTION..............14-11
FUEL RAIL - INSTALLATION............14-11
FUEL RAIL - OPERATION...............14-11
FUEL RAIL - REMOVAL................14-11
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION........................0-1
FUEL SENSOR - DESCRIPTION, WATER
IN ................................14-16
FUEL SENSOR - OPERATION, WATER IN . . 14-16
FUEL SHUTOFF SOL - DESCRIPTION, HI
PRESSURE.........................14-16
FUEL SHUTOFF SOL - OPERATION, HI
PRESSURE.........................14-16
FUEL SUPPLY RESTRICTIONS -
DIAGNOSIS AND TESTING..............14-5
FUEL SYSTEM - DIAGNOSIS AND
TESTING, AIR IN......................14-2
FUEL SYSTEM COMPONENTS -
STANDARD PROCEDURES, CLEANING.....14-2
FUEL SYSTEM PRESSURE - WARNING,
HIGH...............................14-1
FUEL SYSTEM, SPECIAL TOOLS..........14-5
FUEL TANK - DESCRIPTION............14-12
FUEL TANK - INSTALLATION............14-13
FUEL TANK - REMOVAL...............14-12
FUEL TANK MODULE - DESCRIPTION.....14-13
FUEL TANK MODULE - INSTALLATION....14-14
FUEL TANK MODULE - REMOVAL........14-13
FUEL TEMPERATURE SENSOR -
DESCRIPTION.......................14-29
FUEL TEMPERATURE SENSOR -
INSTALLATION.......................14-29
FUEL TEMPERATURE SENSOR -
OPERATION.........................14-29
FUEL TEMPERATURE SENSOR -
REMOVAL..........................14-29
FUNCTION TEST - DIAGNOSIS AND
TESTING............................24-3
FUSE BLOCK #1 - DESCRIPTION......8W-97-2
FUSE BLOCK #1 - INSTALLATION......8W-97-3
FUSE BLOCK #1 - OPERATION........8W-97-2
FUSE BLOCK #1 - REMOVAL.........8W-97-3
FUSE BLOCK #2 - DESCRIPTION......8W-97-3
FUSE BLOCK #2 - OPERATION........8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.......8W-01-8
GALLERY PLUGS - STANDARD
PROCEDURE, REPLACING ENGINE
CORE AND OIL.......................9-34
GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH AIR
.............24-9
GAP AND FLUSH - SPECIFICATIONS
......23-88
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE
......................8J-15
GAUGE - DESCRIPTION, FUEL
...........8J-16
GAUGE - OPERATION, ENGINE
TEMPERATURE
......................8J-15GAUGE - OPERATION, FUEL............8J-16
GAUGES - DIAGNOSIS AND TESTING,
PRESSURE..........................22-8
GEAR - DESCRIPTION..................19-8
GEAR - INSTALLATION.................19-8
GEAR - INSTALLATION, INTERMEDIATE....9-66
GEAR - REMOVAL.....................19-8
GEAR - REMOVAL, INTERMEDIATE........9-61
GEAR SELECTOR INDICATOR -
DESCRIPTION.......................8J-17
GEAR SELECTOR INDICATOR -
OPERATION.........................8J-17
GEAR TO COOLER TUBE -
INSTALLATION, RETURN HOSE FROM....19-15
GEAR TO COOLER TUBE - REMOVAL,
RETURN HOSE FROM.................19-15
GEARSHIFT CABLE - DIAGNOSIS AND
TESTING..........................21-109
GEARSHIFT CABLE - INSTALLATION.....21-109
GEARSHIFT CABLE - REMOVAL........21-109
GEARTRAIN - ASSEMBLY, PLANETARY . . . 21-131
GEARTRAIN - DESCRIPTION,
PLANETARY........................21-130
GEARTRAIN - DISASSEMBLY,
PLANETARY........................21-131
GEARTRAIN - OPERATION, PLANETARY . . 21-130
GENERAL - WARNINGS.............8W-01-6
GENERATOR - DESCRIPTION...........8F-18
GENERATOR - INSTALLATION...........8F-18
GENERATOR - OPERATION.............8F-18
GENERATOR - REMOVAL...............8F-18
GENERATOR DECOUPLER - DIAGNOSIS
AND TESTING.......................8F-19
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-19
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-21
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-19
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-20
GLASS - INSTALLATION, DOOR....23-15,23-31,
23-46
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-49
GLASS - REMOVAL, DOOR . . . 23-15,23-31,23-46
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-49
GLOVE BOX - INSTALLATION...........23-56
GLOVE BOX - REMOVAL...............23-56
GLOW PLUG - INSTALLATION............8I-1
GLOW PLUG - REMOVAL................8I-1
GLOW PLUG RELAY - DESCRIPTION.......8I-2
GLOW PLUG RELAY - OPERATION........8I-2
GLOW PLUG RELAYS - DIAGNOSIS AND
TESTING.............................8I-2
GRILLE - INSTALLATION...............23-47
GRILLE - REMOVAL..................23-47
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-8
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-5
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO
..............................8W-01-8
GUIDE RAIL - INSTALLATION, CYLINDER
HEAD
...............................9-26
GUIDE RAIL - REMOVAL, CYLINDER
HEAD
...............................9-24
HANDLE - INSTALLATION, ASSIST
.......23-68
HANDLE - INSTALLATION, EXTERIOR
....23-16,
23-33,23-36
HANDLE - INSTALLATION, LATCH
RELEASE
...........................23-52
HANDLE - REMOVAL, ASSIST
...........23-68
HANDLE - REMOVAL, EXTERIOR
. . . 23-16,23-32,
23-36
HANDLE - REMOVAL, LATCH RELEASE
. . . 23-52
HANDLE ACTUATOR - INSTALLATION,
INSIDE
........................23-34,23-37
HANDLE ACTUATOR - REMOVAL, INSIDE
. 23-34,
23-37
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE
...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-6
VAINDEX 7
Description Group-Page Description Group-Page Description Group-Page

LATCH STRIKER - REMOVAL, REAR......23-41
LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE........................22-8
LEAK DOWN TEST - STANDARD
PROCEDURE, CYLINDER.................9-3
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-12
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM..........11-4
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM....................7-10
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-46
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEAKS - STANDARD PROCEDURE,
REPAIRING.........................22-10
LEFT MOUNT - INSTALLATION...........9-49
LEFT MOUNT - REMOVAL...............9-49
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID........21-102
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-14
LEVEL - STANDARD PROCEDURE,
CHECK OIL........................21-102
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE......8F-12
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-65
LEVEL INDICATOR - DESCRIPTION, LOW
OIL................................8J-18
LEVEL INDICATOR - OPERATION, LOW
OIL.................................8J-18
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL..................14-15
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL.................14-15
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL.....................14-15
LEVEL SENSOR - INSTALLATION,
COOLANT............................7-13
LEVEL SENSOR - REMOVAL, COOLANT....7-13
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-8
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-16
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-15
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-17
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-16
LEVER - INSTALLATION................5-26
LEVER - INSTALLATION, ALB............5-15
LEVER - REMOVAL....................5-26
LEVER - REMOVAL, ALB................5-15
LICENSE PLATE BRACKET -
INSTALLATION.......................23-47
LICENSE PLATE BRACKET - REMOVAL....23-47
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-18
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-17
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-18
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-18
LIGHTER LAMP UNIT - INSTALLATION,
ASH RECEIVER/CIGAR.................8L-27
LIGHTER LAMP UNIT - REMOVAL, ASH
RECEIVER/CIGAR.....................8L-27
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-1
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-2
LIGHTING - SPECIFICATIONS, INTERIOR . . 8L-26
LINE - DESCRIPTION, REFRIGERANT.....24-44
LINE - INSTALLATION, A/C DISCHARGE . . . 24-54
LINE - INSTALLATION, FUEL............24-76
LINE - INSTALLATION, LIQUID..........24-59
LINE - INSTALLATION, SUCTION.........24-66
LINE - OPERATION, REFRIGERANT
.......24-44
LINE - REMOVAL, A/C DISCHARGE
.......24-53
LINE - REMOVAL, FUEL
................24-75
LINE - REMOVAL, LIQUID
..............24-58
LINE - REMOVAL, SUCTION
............24-66LINE FROM PUMP TO COOLER TUBE -
INSTALLATION, RETURN...............19-15
LINE FROM PUMP TO COOLER TUBE -
REMOVAL, RETURN..................19-15
LINES - DIAGNOSIS AND TESTING, HIGH
PRESSURE FUEL......................14-1
LINES - INSTALLATION, HIGH PRESSURE . . 14-7
LINES - INSTALLATION, OIL COOLER......9-50
LINES - INSTALLATION, UNDERBODY....24-69
LINES - REMOVAL, HIGH PRESSURE......14-6
LINES - REMOVAL, OIL COOLER.........9-50
LINES - REMOVAL, UNDERBODY........24-68
LINES - STANDARD PROCEDURE,
DISCONNECTING AND CONNECTING
FUEL...............................14-2
LINK - INSTALLATION, STABILIZER....2-16,2-9
LINK - REMOVAL, STABILIZER........2-16,2-9
LINKAGE - DESCRIPTION, WIPER.......8R-17
LINKAGE - INSTALLATION, WIPER.......8R-18
LINKAGE - OPERATION, WIPER.........8R-17
LINKAGE - REMOVAL, WIPER...........8R-17
LIQUID LINE - INSTALLATION...........24-59
LIQUID LINE - REMOVAL..............24-58
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL......8W-01-8
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - INSPECTION, FLUID
FILL/CHECK............................0-4
LOCK CABLE - INSTALLATION, PARK....21-126
LOCK CABLE - REMOVAL, PARK........21-125
LOCK CONTROL - INSTALLATION, LATCH . . 23-40
LOCK CONTROL - REMOVAL, LATCH.....23-39
LOCK CYLINDER - INSTALLATION.......23-18
LOCK CYLINDER - REMOVAL...........23-18
LOCK MOTOR - INSTALLATION, DOOR....8N-1
LOCK MOTOR - REMOVAL, DOOR........8N-1
LOCK SWITCH - DESCRIPTION, MASTER . . . 8N-2
LOCK SWITCH - DIAGNOSIS AND
TESTING, MASTER....................8N-2
LOCK SWITCH - INSTALLATION, MASTER . . 8N-2
LOCK SWITCH - REMOVAL, MASTER......8N-2
LOCKS - DESCRIPTION, POWER.........8N-1
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-34
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-33
LOSS - STANDARD PROCEDURE,
DETERMINING CYLINDER PRESSURE......9-4
LOW BEAM HEADLAMP BULB -
INSTALLATION.......................8L-19
LOW BEAM HEADLAMP BULB -
REMOVAL..........................8L-18
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-18
LOW FUEL INDICATOR - OPERATION.....8J-18
LOW INDICATOR - DESCRIPTION,
COOLANT...........................8J-14
LOW INDICATOR - OPERATION,
COOLANT...........................8J-14
LOW OIL LEVEL INDICATOR -
DESCRIPTION.......................8J-18
LOW OIL LEVEL INDICATOR -
OPERATION.........................8J-18
LOW PRESSURE FUEL PUMP TEST -
STANDARD PROCEDURE................14-3
LOW PRESSURE PUMP - DESCRIPTION . . . 14-7
LOW PRESSURE PUMP - INSTALLATION . . 14-11
LOW PRESSURE PUMP - OPERATION.....14-8
LOW PRESSURE PUMP - REMOVAL
.......14-9
LOWER BALL JOINT - INSTALLATION
......2-6
LOWER BALL JOINT - REMOVAL
..........2-6
LOWER CONTROL ARM - INSTALLATION
....2-6
LOWER CONTROL ARM - REMOVAL
.......2-6
LOWER ROLLER ARM - INSTALLATION
. . . 23-38
LOWER ROLLER ARM - REMOVAL
.......23-38
LUBRICANT RECOMMENDATIONS -
STANDARD PROCEDURE, PARTS
..........0-5
MAINTENANCE INDICATOR -
DESCRIPTION
.......................8J-19
MAINTENANCE INDICATOR - OPERATION
. . 8J-19
MAINTENANCE SCHEDULES -
DESCRIPTION
.........................0-7
MALFUNCTION INDICATOR -
DESCRIPTION, TRACTION CONTROL
.....8J-25
MALFUNCTION INDICATOR -
OPERATION, TRACTION CONTROL
.......8J-25MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-20
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-20
MANIFOLD - INSTALLATION, EXHAUST....9-59
MANIFOLD - INSTALLATION, INTAKE......9-58
MANIFOLD - REMOVAL, EXHAUST........9-59
MANIFOLD - REMOVAL, INTAKE..........9-57
MANIFOLD AIR FLOW (MAF) SENSOR -
DESCRIPTION.......................14-30
MANIFOLD AIR FLOW (MAF) SENSOR -
INSTALLATION.......................14-31
MANIFOLD AIR FLOW (MAF) SENSOR -
OPERATION.........................14-30
MANIFOLD AIR FLOW (MAF) SENSOR -
REMOVAL..........................14-31
MANUAL - INSTALLATION, WINDOW
REGULATOR........................23-23
MANUAL - REMOVAL, WINDOW
REGULATOR........................23-22
MANUAL BLEEDING - STANDARD
PROCEDURE..........................5-4
MARKER LAMP BULB - INSTALLATION,
FRONT TURN/PARK/SIDE..............8L-15
MARKER LAMP BULB - INSTALLATION,
REAR SIDE.........................8L-21
MARKER LAMP BULB - REMOVAL,
FRONT TURN/PARK/SIDE..............8L-14
MARKER LAMP BULB - REMOVAL, REAR
SIDE..............................8L-21
MASTER CYLINDER - INSTALLATION......5-18
MASTER CYLINDER - REMOVAL...........5-17
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-17
MASTER CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING..............5-16
MASTER LOCK SWITCH - DESCRIPTION . . . 8N-2
MASTER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-2
MASTER LOCK SWITCH - INSTALLATION . . 8N-2
MASTER LOCK SWITCH - REMOVAL......8N-2
MATCH MOUNTING - STANDARD
PROCEDURE.........................22-2
MATS - INSTALLATION, CARPETS AND
FLOOR.............................23-70
MATS - REMOVAL, CARPETS AND
FLOOR.............................23-69
MEASURE CRANKSHAFT AND BLOCK
JOURNALS - STANDARD PROCEDURE.....9-35
MEASURE CYLINDER HEAD SURFACE -
STANDARD PROCEDURE................9-21
MEASURING CYLINDER BORES -
STANDARD PROCEDURE................9-34
MEASURING PISTON PROTRUSION -
STANDARD PROCEDURE................9-42
MECHANISM - DESCRIPTION, SHIFT....21-133
MECHANISM - INSTALLATION, SHIFT....21-135
MECHANISM - OPERATION, SHIFT......21-133
MECHANISM - REMOVAL, SHIFT.......21-134
METRIC SYSTEM - DESCRIPTION......Intro.-5
MICRO 420 BATTERY TESTER -
STANDARD PROCEDURE, USING........8F-11
MIRROR - GLASS - INSTALLATION, SIDE
VIEW..............................23-49
MIRROR - GLASS - REMOVAL, SIDE
VIEW..............................23-49
MIRROR - INSTALLATION, SIDE VIEW....23-48
MIRROR - REMOVAL, REAR VIEW.......23-72
MIRROR - REMOVAL, SIDE VIEW
........23-48
MIRROR SUPPORT BRACKET -
INSTALLATION, REAR VIEW
............23-72
MIRROR SWITCH - DIAGNOSIS AND
TESTING, POWER
.....................8N-3
MIRROR SWITCH - INSTALLATION,
POWER
.............................8N-4
MIRROR SWITCH - REMOVAL, POWER
....8N-3
MIRRORS - DESCRIPTION, POWER
.......8N-3
MODE DOOR CABLES - INSTALLATION
. . . 24-19
MODE DOOR CABLES - REMOVAL
.......24-19
MODULE - DESCRIPTION, AIRBAG
CONTROL
...........................8O-8
MODULE - DESCRIPTION, CENTRAL
TIMER
..............................8E-1
MODULE - DESCRIPTION, CONTROL
.....24-24
MODULE - DESCRIPTION, ENGINE
CONTROL
...........................8E-3
MODULE - DESCRIPTION, FUEL TANK
....14-13
10 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT.......................23-55
PANEL DUCTS - INSTALLATION,
INSTRUMENT.......................24-38
PANEL DUCTS - REMOVAL,
INSTRUMENT.......................24-37
PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC BODY............23-3
PARK BRAKE, SPECIAL TOOLS...........5-23
PARK BRAKE SWITCH - INSTALLATION . . . 8L-20
PARK BRAKE SWITCH - REMOVAL.......8L-20
PARK LOCK CABLE - INSTALLATION.....21-126
PARK LOCK CABLE - REMOVAL........21-125
PARKING BRAKE CABLES -
ADJUSTMENT........................5-25
PARK/NEUTRAL CONTACT -
DESCRIPTION......................21-139
PARK/NEUTRAL CONTACT - OPERATION . 21-140
PARTS & LUBRICANT
RECOMMENDATIONS - STANDARD
PROCEDURE..........................0-5
PASSENGER AIRBAG - DESCRIPTION....8O-23
PASSENGER AIRBAG - INSTALLATION....8O-26
PASSENGER AIRBAG - OPERATION......8O-24
PASSENGER AIRBAG - REMOVAL........8O-24
PASSENGER AIRBAG BRACKET -
INSTALLATION......................8O-27
PASSENGER AIRBAG BRACKET -
REMOVAL..........................8O-27
PASSENGER HEATED SEAT SWITCH -
DESCRIPTION.........................8G-5
PASSENGER HEATED SEAT SWITCH -
DIAGNOSIS AND TESTING..............8G-5
PASSENGER HEATED SEAT SWITCH -
INSTALLATION.......................8G-5
PASSENGER HEATED SEAT SWITCH -
OPERATION..........................8G-5
PASSENGER HEATED SEAT SWITCH -
REMOVAL...........................8G-5
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PEDAL - INSTALLATION................5-19
PEDAL - REMOVAL....................5-18
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR..........14-17
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-4
PERFORMANCE TEST - DIAGNOSIS AND
TESTING, A/C........................24-3
PILLAR - INSTALLATION, REAR.........8L-29
PILLAR - REMOVAL, REAR.............8L-28
PINION SEAL - INSTALLATION...........3-22
PINION SEAL - REMOVAL...............3-22
PIPE - INSTALLATION, EXHAUST.........11-3
PIPE - REMOVAL, EXHAUST.............11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-40
PISTON PROTRUSION - STANDARD
PROCEDURE, MEASURING..............9-42
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-46
PISTONS - DESCRIPTION.............21-128
PISTONS - OPERATION...............21-128
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-131
PLANETARY GEARTRAIN - DESCRIPTION . 21-130
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-131
PLANETARY GEARTRAIN - OPERATION . . 21-130
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE BRACKET - INSTALLATION,
LICENSE...........................23-47
PLATE BRACKET - REMOVAL, LICENSE . . . 23-47
PLATE LAMP BULB - INSTALLATION,
LICENSE...........................8L-18
PLATE LAMP BULB - REMOVAL,
LICENSE...........................8L-17
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-18
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-18
PLATES - INSTALLATION, SPRING
CLAMP..............................2-8
PLATES - INSTALLATION, SPRING STOP....2-9
PLATES - REMOVAL, SPRING CLAMP
......2-8
PLATES - REMOVAL, SPRING STOP
........2-9
PLUG - INSTALLATION, GLOW
............8I-1
PLUG - REMOVAL, GLOW
...............8I-1
PLUG RELAY - DESCRIPTION, GLOW
......8I-2PLUG RELAY - OPERATION, GLOW........8I-2
PLUG RELAYS - DIAGNOSIS AND
TESTING, GLOW.......................8I-2
PLUGS - STANDARD PROCEDURE,
REPLACING ENGINE CORE AND OIL
GALLERY............................9-34
PLUMBING - CLEANING, CHARGE AIR
COOLER.............................11-5
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER.........................11-4
PLUMBING - INSPECTION, CHARGE AIR
COOLER.............................11-5
PLUMBING - INSTALLATION, CHARGE
AIR COOLER.........................11-5
PLUMBING - OPERATION, CHARGE AIR
COOLER.............................11-4
PLUMBING - REMOVAL, CHARGE AIR
COOLER.............................11-5
PLUMBING - WARNING................24-44
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISH - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-75
POSITION - STANDARD PROCEDURE,
CHECKING CAMSHAFT.................9-27
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-14
POSITION LAMP BULB - REMOVAL,
FRONT.............................8L-14
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-17
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-19
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT.......................14-20
POSITION SENSOR - INSTALLATION,
CAMSHAFT.........................14-19
POSITION SENSOR - INSTALLATION,
CRANKSHAFT.......................14-20
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-19
POSITION SENSOR - OPERATION,
CRANKSHAFT.......................14-20
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-19
POSITION SENSOR - REMOVAL,
CRANKSHAFT.......................14-20
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-7
POWER - INSTALLATION, WINDOW
REGULATOR........................23-21
POWER - REMOVAL, WINDOW
REGULATOR........................23-20
POWER BRAKE BOOSTER -
DESCRIPTION........................5-19
POWER BRAKE BOOSTER -
INSTALLATION........................5-19
POWER BRAKE BOOSTER - OPERATION . . . 5-19
POWER BRAKE BOOSTER - REMOVAL.....5-19
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-3
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-3
POWER LOCKS - DESCRIPTION..........8N-1
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING........................8N-3
POWER MIRROR SWITCH -
INSTALLATION.......................8N-4
POWER MIRROR SWITCH - REMOVAL....8N-3
POWER MIRRORS - DESCRIPTION.......8N-3
POWER OUTLET - DESCRIPTION......8W-97-3
POWER OUTLET - DIAGNOSIS AND
TESTING.........................8W-97-4
POWER OUTLET - INSTALLATION.....8W-97-4
POWER OUTLET - OPERATION........8W-97-4
POWER OUTLET - REMOVAL.........8W-97-4
POWER STEERING FLUID -
DESCRIPTION
.........................0-3
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE
. . . 19-12
POWER STEERING PUMP FILL AND
BLEED PROCEDURE, STANDARD
PROCEDURE
........................19-14
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING
..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING
.....19-13POWER WINDOW SWITCH - DIAGNOSIS
AND TESTING........................8N-5
POWER WINDOW SWITCH -
INSTALLATION.......................8N-6
POWER WINDOW SWITCH - REMOVAL....8N-6
POWER WINDOWS - DESCRIPTION.......8N-5
POWER WINDOWS - OPERATION.........8N-5
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-8
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING..............2-17
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY...................23-1
PRECAUTIONS, CAUTION -
REFRIGERANT HOSES/LINES/TUBES......24-45
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY.................23-82
PRELIMINARY - DIAGNOSIS AND
TESTING...........................21-23
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING.........................7-1
PRESSURE - WARNING, HIGH FUEL
SYSTEM............................14-1
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-18
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-19
PRESSURE CAP - OPERATION,
RADIATOR...........................7-18
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE...................22-6
PRESSURE FUEL LINES - DIAGNOSIS
AND TESTING, HIGH...................14-1
PRESSURE FUEL PUMP TEST -
STANDARD PROCEDURE, LOW...........14-3
PRESSURE FUEL SHUTOFF SOL -
DESCRIPTION, HI....................14-16
PRESSURE FUEL SHUTOFF SOL -
OPERATION, HI......................14-16
PRESSURE GAUGES - DIAGNOSIS AND
TESTING............................22-8
PRESSURE HOSE - INSTALLATION.......19-15
PRESSURE HOSE - REMOVAL..........19-15
PRESSURE LINES - INSTALLATION, HIGH . . 14-7
PRESSURE LINES - REMOVAL, HIGH......14-6
PRESSURE LOSS - STANDARD
PROCEDURE, DETERMINING
CYLINDER............................9-4
PRESSURE PUMP - DESCRIPTION, HIGH . . . 14-7
PRESSURE PUMP - DESCRIPTION, LOW . . . 14-7
PRESSURE PUMP - INSTALLATION,
HIGH..............................14-10
PRESSURE PUMP - INSTALLATION, LOW . 14-11
PRESSURE PUMP - OPERATION, LOW.....14-8
PRESSURE PUMP - REMOVAL, HIGH......14-8
PRESSURE PUMP - REMOVAL, LOW......14-9
PRESSURE SENSOR - DESCRIPTION,
BOOST.............................14-17
PRESSURE SENSOR - DIAGNOSIS AND
TESTING, BOOST.....................14-18
PRESSURE SENSOR - INSTALLATION,
BOOST.............................14-18
PRESSURE SENSOR - OPERATION,
BOOST.............................14-18
PRESSURE SENSOR - REMOVAL, BOOST . . 14-18
PRESSURE SOLENOID - DESCRIPTION,
FUEL..............................14-27
PRESSURE SOLENOID - INSTALLATION,
FUEL..............................14-28
PRESSURE SOLENOID - OPERATION,
FUEL..............................14-27
PRESSURE SOLENOID - REMOVAL, FUEL . 14-28
PRESSURE TRANSDUCER -
DESCRIPTION, A/C...................24-13
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-13
PRESSURE TRANSDUCER -
INSTALLATION, A/C
...................24-14
PRESSURE TRANSDUCER - OPERATION,
A/C
................................24-13
PRESSURE TRANSDUCER - REMOVAL,
A/C
................................24-14
PRESSURES - DESCRIPTION, TIRE
INFLATION
...........................22-7
PROP ROD - INSTALLATION
............23-52
12 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

PROP ROD - REMOVAL................23-52
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - INSTALLATION.......3-6
PROPELLER SHAFT - REMOVAL...........3-6
PROPELLER SHAFT - SPECIAL TOOLS......3-5
PROPELLER SHAFT - SPECIFICATIONS......3-5
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROTRUSION - STANDARD PROCEDURE,
MEASURING PISTON...................9-42
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER........................8F-19
PULLEY - INSTALLATION, GENERATOR
DECOUPLER........................8F-21
PULLEY - OPERATION, GENERATOR
DECOUPLER........................8F-19
PULLEY - REMOVAL, GENERATOR
DECOUPLER........................8F-20
PUMP - ASSEMBLY, OIL..............21-121
PUMP - DESCRIPTION................19-12
PUMP - DESCRIPTION, ELECTRIC
COOLANT...........................24-57
PUMP - DESCRIPTION, FUEL DOSING....24-74
PUMP - DESCRIPTION, HIGH PRESSURE . . . 14-7
PUMP - DESCRIPTION, LOW PRESSURE . . . 14-7
PUMP - DESCRIPTION, OIL............21-120
PUMP - DESCRIPTION, VACUUM.........9-48
PUMP - DISASSEMBLY, OIL...........21-120
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-12
PUMP - INSTALLATION, ELECTRIC
COOLANT...........................24-57
PUMP - INSTALLATION, FUEL DOSING....24-74
PUMP - INSTALLATION, HIGH
PRESSURE.........................14-10
PUMP - INSTALLATION, LOW PRESSURE . 14-11
PUMP - INSTALLATION, VACUUM.........9-49
PUMP - INSTALLATION, WATER..........7-20
PUMP - OPERATION..................19-12
PUMP - OPERATION, ELECTRIC
COOLANT...........................24-57
PUMP - OPERATION, FUEL DOSING......24-74
PUMP - OPERATION, LOW PRESSURE.....14-8
PUMP - OPERATION, OIL.............21-120
PUMP - OPERATION, VACUUM...........9-48
PUMP - REMOVAL, ELECTRIC COOLANT . . 24-57
PUMP - REMOVAL, FUEL DOSING.......24-74
PUMP - REMOVAL, HIGH PRESSURE......14-8
PUMP - REMOVAL, LOW PRESSURE......14-9
PUMP - REMOVAL, VACUUM............9-48
PUMP - REMOVAL, WATER..............7-19
PUMP CHAIN - INSTALLATION, OIL.......9-54
PUMP CHAIN - REMOVAL, OIL...........9-53
PUMP FILL AND BLEED PROCEDURE,
STANDARD PROCEDURE - POWER
STEERING..........................19-14
PUMP LEAKAGE - DIAGNOSIS AND
TESTING...........................19-12
PUMP TEST - STANDARD PROCEDURE,
LOW PRESSURE FUEL.................14-3
PUMP TO COOLER TUBE -
INSTALLATION, RETURN LINE FROM.....19-15
PUMP TO COOLER TUBE - REMOVAL,
RETURN LINE FROM..................19-15
PUMP/MOTOR - DESCRIPTION, WASHER . . 8R-9
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-10
PUMP/MOTOR - OPERATION, WASHER . . . 8R-10
PUMP/MOTOR - REMOVAL, WASHER....8R-10
QUARTER TRIM PANEL - INSTALLATION . . 23-72
QUARTER TRIM PANEL - REMOVAL......23-71
QUARTER WINDOW - INSTALLATION.....23-81
QUARTER WINDOW - REMOVAL.........23-81
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - INSTALLATION.............7-17
RADIATOR - REMOVAL.................7-16
RADIATOR CROSSMEMBER -
INSTALLATION.......................23-48
RADIATOR CROSSMEMBER - REMOVAL . . 23-47
RADIATOR FAN - INSTALLATION
..........7-13
RADIATOR FAN - REMOVAL
.............7-13
RADIATOR PRESSURE CAP -
DESCRIPTION
........................7-18
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING
........................7-19
RADIATOR PRESSURE CAP - OPERATION
. . 7-18RADIO - INSTALLATION................8A-2
RADIO - REMOVAL....................8A-2
RAIL - DESCRIPTION, FUEL............14-11
RAIL - INSTALLATION, CYLINDER HEAD
GUIDE..............................9-26
RAIL - INSTALLATION, FUEL............14-11
RAIL - INSTALLATION, TENSIONING AND
SLIDE..............................9-66
RAIL - INSTALLATION, TIMING CHAIN
TENSIONING.........................9-66
RAIL - OPERATION, FUEL..............14-11
RAIL - REMOVAL, CYLINDER HEAD
GUIDE..............................9-24
RAIL - REMOVAL, FUEL...............14-11
RAIL - REMOVAL, TIMING CHAIN
TENSIONING.........................9-63
RAILS - REMOVAL, TENSIONING AND
SLIDE..............................9-61
RATTLE - STANDARD PROCEDURE,
BUZZ, SQUEAK......................23-10
REAR - DESCRIPTION..................2-11
REAR - INSTALLATION.........5-14,5-22,5-25
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-37
REAR - INSTALLATION, SEAT...........23-79
REAR - INSTALLATION, SEAT BACK
CUSHION/COVER.....................23-80
REAR - INSTALLATION, SEAT CUSHION/
COVER.............................23-80
REAR - REMOVAL.............5-13,5-22,5-24
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-37
REAR - REMOVAL, SEAT...............23-79
REAR - REMOVAL, SEAT BACK
CUSHION/COVER.....................23-80
REAR - REMOVAL, SEAT CUSHION/
COVER.............................23-80
REAR (15º WHEELS) (SRW) - REMOVAL....5-9
REAR (16º WHEELS) (SRW) -
INSTALLATION........................5-11
REAR (16º WHEELS) (SRW) - REMOVAL....5-9
REAR A/C HOUSING - INSTALLATION.....24-41
REAR A/C HOUSING - REMOVAL........24-40
REAR AXLE - DESCRIPTION.............3-10
REAR AXLE - DIAGNOSIS AND TESTING . . . 3-10
REAR AXLE - INSTALLATION............3-12
REAR AXLE - OPERATION...............3-10
REAR AXLE - REMOVAL................3-11
REAR AXLE - SPECIAL TOOLS...........3-14
REAR AXLE - SPECIFICATIONS...........3-13
REAR BUMPER - STEP - INSTALLATION . . . 13-3
REAR BUMPER - STEP - REMOVAL.......13-3
REAR CROSSMEMBER - TRANSMISSION
- INSTALLATION......................13-9
REAR CROSSMEMBER - TRANSMISSION
- REMOVAL..........................13-9
REAR DRUM IN HAT BRAKE - CLEANING . . . 5-27
REAR (DRW) - INSTALLATION . . . 5-11,5-13,5-21
REAR (DRW) - REMOVAL.......5-10,5-12,5-20
REAR EVAPORATOR - INSTALLATION.....24-61
REAR EVAPORATOR - REMOVAL........24-60
REAR EXPANSION VALVE -
INSTALLATION.......................24-63
REAR EXPANSION VALVE - REMOVAL....24-62
REAR FASCIA - INSTALLATION...........13-3
REAR FASCIA - REMOVAL...............13-3
REAR LATCH - INSTALLATION..........23-40
REAR LATCH - REMOVAL..............23-40
REAR LATCH STRIKER - INSTALLATION . . . 23-41
REAR LATCH STRIKER - REMOVAL......23-41
REAR PILLAR - INSTALLATION..........8L-29
REAR PILLAR - REMOVAL.............8L-28
REAR SEAT BACK SHIELD -
INSTALLATION.......................23-79
REAR SEAT BACK SHIELD - REMOVAL....23-79
REAR SEAT BELT & RETRACTOR -
INSTALLATION......................8O-29
REAR SEAT BELT & RETRACTOR -
REMOVAL..........................8O-27
REAR SIDE MARKER LAMP BULB -
INSTALLATION.......................8L-21
REAR SIDE MARKER LAMP BULB -
REMOVAL
..........................8L-21
REAR (SRW) - INSTALLATION
.......5-13,5-21
REAR (SRW) - REMOVAL
...........5-12,5-20
REAR TURN LAMP BULB -
INSTALLATION
.......................8L-22
REAR TURN LAMP BULB - REMOVAL
....8L-21REAR VIEW MIRROR - REMOVAL........23-72
REAR VIEW MIRROR SUPPORT
BRACKET - INSTALLATION.............23-72
REAR WHEEL INSTALLATION -
STANDARD PROCEDURE, DUAL.........22-12
REAR WHEEL SPEED SENSOR -
INSTALLATION........................5-31
REAR WHEEL SPEED SENSOR -
REMOVAL...........................5-30
REAR WHEELS - INSTALLATION, AXLE
SHAFTS - DUAL.......................3-19
REAR WHEELS - REMOVAL, AXLE
SHAFTS - DUAL.......................3-19
RECEIVER - INSTALLATION, ASH........23-55
RECEIVER - REMOVAL, ASH............23-55
RECEIVER/CIGAR LIGHTER LAMP UNIT -
INSTALLATION, ASH..................8L-27
RECEIVER/CIGAR LIGHTER LAMP UNIT -
REMOVAL, ASH......................8L-27
RECEIVER/DRIER - DESCRIPTION........24-64
RECEIVER/DRIER - INSTALLATION.......24-64
RECEIVER/DRIER - OPERATION.........24-64
RECEIVER/DRIER - REMOVAL...........24-64
RECIRCULATION DOOR ACTUATOR -
DESCRIPTION.......................24-20
RECIRCULATION DOOR ACTUATOR -
INSTALLATION.......................24-21
RECIRCULATION DOOR ACTUATOR -
OPERATION.........................24-20
RECIRCULATION DOOR ACTUATOR -
REMOVAL..........................24-21
RECOMMENDATIONS - STANDARD
PROCEDURE, PARTS & LUBRICANT........0-5
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT.......................24-47
REFERENCES - DESCRIPTION, TORQUE . . Intro.-7
REFILLING COOLING SYSTEM -
STANDARD PROCEDURE................7-12
REFRIGERANT - DESCRIPTION..........24-65
REFRIGERANT - OPERATION............24-65
REFRIGERANT HOSES/LINES/TUBES
PRECAUTIONS, CAUTION..............24-45
REFRIGERANT LINE - DESCRIPTION......24-44
REFRIGERANT LINE - OPERATION.......24-44
REFRIGERANT OIL - DESCRIPTION......24-65
REFRIGERANT OIL - OPERATION........24-65
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-65
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-47
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-48
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-47
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING.............24-46
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-46
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-23
REGULATOR - MANUAL - INSTALLATION,
WINDOW...........................23-23
REGULATOR - MANUAL - REMOVAL,
WINDOW...........................23-22
REGULATOR - POWER - INSTALLATION,
WINDOW...........................23-21
REGULATOR - POWER - REMOVAL,
WINDOW...........................23-20
RELAY - DESCRIPTION..............8W-97-4
RELAY - DESCRIPTION, BLOWER
MOTOR
............................24-23
RELAY - DESCRIPTION, GLOW PLUG
......8I-2
RELAY - DESCRIPTION, HEATED SEAT
.....8G-4
RELAY - DESCRIPTION, STARTER
MOTOR
............................8F-31
RELAY - DESCRIPTION, WIPER
.........8R-20
RELAY - DIAGNOSIS AND TESTING
....8W-97-5
RELAY - DIAGNOSIS AND TESTING,
BLOWER MOTOR
....................24-24
RELAY - DIAGNOSIS AND TESTING,
HEATED SEAT
........................8G-4
RELAY - INSTALLATION
.............8W-97-5
RELAY - INSTALLATION, BLOWER
MOTOR
............................24-24
RELAY - INSTALLATION, DAYTIME
RUNNING LAMP
......................8L-9
RELAY - INSTALLATION, FOG LAMP
......8L-11
RELAY - INSTALLATION, HEATED SEAT
....8G-4
VAINDEX 13
Description Group-Page Description Group-Page Description Group-Page

SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL............14-15
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL............14-15
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL.........................14-15
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-7
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION....................14-17
SENSOR - DESCRIPTION, AIR OUTLET
TEMPERATURE......................24-14
SENSOR - DESCRIPTION, AMBIENT
TEMPERATURE......................24-15
SENSOR - DESCRIPTION, BOOST
PRESSURE.........................14-17
SENSOR - DESCRIPTION, CAMSHAFT
POSITION..........................14-19
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-20
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMP......................7-14
SENSOR - DESCRIPTION, EVAPORATOR
TEMPERATURE.................24-17,24-25
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT......................14-15
SENSOR - DESCRIPTION, FUEL
TEMPERATURE......................14-29
SENSOR - DESCRIPTION, HEATED SEAT . . . 8G-4
SENSOR - DESCRIPTION, IN-CAR
TEMPERATURE......................24-19
SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE........................14-29
SENSOR - DESCRIPTION, MANIFOLD AIR
FLOW (MAF)........................14-30
SENSOR - DESCRIPTION, OIL
TEMPERATURE.......................9-56
SENSOR - DESCRIPTION, TEMPERATURE . 24-30
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE........21-140
SENSOR - DESCRIPTION, WATER IN
FUEL..............................14-16
SENSOR - DIAGNOSIS AND TESTING,
BOOST PRESSURE...................14-18
SENSOR - DIAGNOSIS AND TESTING,
EVAPORATOR TEMPERATURE...........24-26
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8G-4
SENSOR - DIAGNOSIS AND TESTING,
IN-CAR TEMPERATURE................24-19
SENSOR - DIAGNOSIS AND TESTING,
TEMPERATURE......................24-30
SENSOR - INSTALLATION, AIR OUTLET
TEMPERATURE......................24-15
SENSOR - INSTALLATION, AMBIENT
TEMPERATURE......................24-16
SENSOR - INSTALLATION, BOOST
PRESSURE.........................14-18
SENSOR - INSTALLATION, CAMSHAFT
POSITION..........................14-19
SENSOR - INSTALLATION, COOLANT
LEVEL..............................7-13
SENSOR - INSTALLATION, CRANKSHAFT
POSITION..........................14-20
SENSOR - INSTALLATION, DOME
LAMP/INTRUSION....................8L-31
SENSOR - INSTALLATION, ENGINE
COOLANT TEMP......................7-15
SENSOR - INSTALLATION, EVAPORATOR
TEMPERATURE.................24-18,24-26
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-30
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT......................14-15
SENSOR - INSTALLATION, FUEL
TEMPERATURE......................14-29
SENSOR - INSTALLATION, INLET AIR
TEMPERATURE......................14-30
SENSOR - INSTALLATION, INTRUSION
....8Q-2
SENSOR - INSTALLATION, MANIFOLD
AIR FLOW (MAF)
.....................14-31
SENSOR - INSTALLATION, OIL
TEMPERATURE
.......................9-57
SENSOR - INSTALLATION, REAR WHEEL
SPEED
..............................5-31
SENSOR - INSTALLATION,
TEMPERATURE
......................24-30SENSOR - OPERATION, AIR OUTLET
TEMPERATURE......................24-15
SENSOR - OPERATION, AMBIENT
TEMPERATURE......................24-15
SENSOR - OPERATION, BOOST
PRESSURE.........................14-18
SENSOR - OPERATION, CAMSHAFT
POSITION..........................14-19
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-20
SENSOR - OPERATION, EVAPORATOR
TEMPERATURE.................24-18,24-26
SENSOR - OPERATION, FUEL
TEMPERATURE......................14-29
SENSOR - OPERATION, IN-CAR
TEMPERATURE......................24-19
SENSOR - OPERATION, INLET AIR
TEMPERATURE......................14-29
SENSOR - OPERATION, MANIFOLD AIR
FLOW (MAF)........................14-30
SENSOR - OPERATION, OIL
TEMPERATURE.......................9-56
SENSOR - OPERATION, TEMPERATURE . . . 24-30
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE.....................21-141
SENSOR - OPERATION, WATER IN FUEL . . 14-16
SENSOR - REMOVAL, AIR OUTLET
TEMPERATURE......................24-15
SENSOR - REMOVAL, AMBIENT
TEMPERATURE......................24-15
SENSOR - REMOVAL, BOOST PRESSURE . . 14-18
SENSOR - REMOVAL, CAMSHAFT
POSITION............................14-19
SENSOR - REMOVAL, COOLANT LEVEL....7-13
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-20
SENSOR - REMOVAL, DOME LAMP/
INTRUSION.........................8L-31
SENSOR - REMOVAL, ENGINE COOLANT
TEMP...............................7-14
SENSOR - REMOVAL, EVAPORATOR
TEMPERATURE.................24-18,24-26
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-30
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT......................14-15
SENSOR - REMOVAL, FUEL
TEMPERATURE......................14-29
SENSOR - REMOVAL, IN-CAR
TEMPERATURE......................24-19
SENSOR - REMOVAL, INLET AIR
TEMPERATURE......................14-30
SENSOR - REMOVAL, INTRUSION........8Q-2
SENSOR - REMOVAL, MANIFOLD AIR
FLOW (MAF)........................14-31
SENSOR - REMOVAL, OIL
TEMPERATURE.......................9-57
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-30
SENSOR - REMOVAL, TEMPERATURE....24-30
SENSOR BULB - INSTALLATION, DOME
LAMP/INTRUSION....................8L-30
SENSOR BULB - REMOVAL, DOME
LAMP/INTRUSION....................8L-30
SENSORS - DESCRIPTION, INPUT SPEED . 21-119
SENSORS - OPERATION, INPUT SPEED . . 21-119
SENTRY KEY REMOTE ENTRY MODULE -
DESCRIPTION........................8Q-2
SENTRY KEY REMOTE ENTRY MODULE -
INSTALLATION.......................8Q-4
SENTRY KEY REMOTE ENTRY MODULE -
OPERATION..........................8Q-3
SENTRY KEY REMOTE ENTRY MODULE -
REMOVAL...........................8Q-3
SEPARATOR - INSTALLATION, OIL........9-50
SEPARATOR - REMOVAL, OIL............9-50
SERVO - DESCRIPTION.................8P-3
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-8
SHACKLE - INSTALLATION, SPRING.......2-15
SHACKLE - REMOVAL, SPRING..........2-15
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER
...........................3-1
SHAFT - INSTALLATION, INTERMEDIATE
. . . 19-5
SHAFT - INSTALLATION, PROPELLER
.......3-6
SHAFT - REMOVAL, INTERMEDIATE
.......19-5
SHAFT - REMOVAL, PROPELLER
..........3-6SHAFT - SPECIAL TOOLS, PROPELLER.....3-5
SHAFT - SPECIFICATIONS, PROPELLER.....3-5
SHAFT - STANDARD PROCEDURE,
PROPELLER...........................3-3
SHAFT BEARING - INSTALLATION,
OUTPUT...........................21-122
SHAFT BEARING - REMOVAL, OUTPUT . . . 21-122
SHAFT SEAL - INSTALLATION, OUTPUT . . 21-125
SHAFT SEAL - REMOVAL, OUTPUT......21-125
SHAFTS - DUAL REAR WHEELS -
INSTALLATION, AXLE..................3-19
SHAFTS - DUAL REAR WHEELS -
REMOVAL, AXLE......................3-19
SHAFTS - INSTALLATION, AXLE..........3-15
SHAFTS - REMOVAL, AXLE..............3-15
SHIELD - INSTALLATION, REAR SEAT
BACK..............................23-79
SHIELD - REMOVAL, REAR SEAT BACK . . . 23-79
SHIFT MECHANISM - DESCRIPTION.....21-133
SHIFT MECHANISM - INSTALLATION....21-135
SHIFT MECHANISM - OPERATION......21-133
SHIFT MECHANISM - REMOVAL........21-134
SHOCK - DIAGNOSIS AND TESTING.......2-13
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-11
SHOCK - INSTALLATION................2-13
SHOCK - REMOVAL....................2-13
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A..........8W-01-8
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A ...........................8W-01-8
SHUTOFF SOL - DESCRIPTION, HI
PRESSURE FUEL.....................14-16
SHUTOFF SOL - OPERATION, HI
PRESSURE FUEL.....................14-16
SIDE MARKER LAMP BULB -
INSTALLATION, REAR.................8L-21
SIDE MARKER LAMP BULB - REMOVAL,
REAR..............................8L-21
SIDE VIEW MIRROR - GLASS -
INSTALLATION.......................23-49
SIDE VIEW MIRROR - GLASS -
REMOVAL..........................23-49
SIDE VIEW MIRROR - INSTALLATION.....23-48
SIDE VIEW MIRROR - REMOVAL........23-48
SIGNAL INDICATOR - DESCRIPTION,
TURN..............................8J-25
SIGNAL INDICATOR - OPERATION, TURN . . 8J-25
SIGNAL RELAY - INSTALLATION, TURN . . . 8L-24
SIGNAL RELAY - REMOVAL, TURN.......8L-24
SIREN - INSTALLATION................8Q-4
SIREN - REMOVAL....................8Q-4
SLIDE RAIL - INSTALLATION,
TENSIONING.........................9-66
SLIDE RAILS - REMOVAL, TENSIONING....9-61
SLIDING DOOR - ASSEMBLY...........23-43
SLIDING DOOR - DISASSEMBLY.........23-42
SLIDING DOOR - INSTALLATION.........23-44
SLIDING DOOR - REMOVAL............23-41
SOL - DESCRIPTION, HI PRESSURE
FUEL SHUTOFF......................14-16
SOL - OPERATION, HI PRESSURE FUEL
SHUTOFF...........................14-16
SOLENOID - DESCRIPTION............21-136
SOLENOID - DESCRIPTION, FUEL
PRESSURE.........................14-27
SOLENOID - INSTALLATION, FUEL
PRESSURE.........................14-28
SOLENOID - OPERATION..............21-138
SOLENOID - OPERATION, FUEL
PRESSURE.........................14-27
SOLENOID - REMOVAL, FUEL PRESSURE . 14-28
SOLENOID VALVE - DESCRIPTION.......24-27
SOLENOID VALVE - DIAGNOSIS AND
TESTING...........................24-27
SOLENOID VALVE - INSTALLATION.......24-28
SOLENOID VALVE - OPERATION.........24-27
SOLENOID VALVE - REMOVAL..........24-27
SPARE TIRE CARRIER - INSTALLATION . . . 22-10
SPARE TIRE CARRIER - REMOVAL.......22-10
SPEAKER - INSTALLATION
..............8A-2
SPEAKER - REMOVAL
..................8A-2
SPEED CONTROL - DESCRIPTION
........8P-1
SPEED CONTROL - OPERATION
..........8P-1
SPEED SENSOR - INSTALLATION, FRONT
WHEEL
.............................5-30
VAINDEX 15
Description Group-Page Description Group-Page Description Group-Page