2005 LEXUS ES300 brake rotor

F40303
SST
Bolt
SST
F40302
LHRH
F40304
SST
- BRAKESKID CONTROL SENSOR
32-57
2491 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
6. REMOVE SKID CONTROL SENSOR
(a) Mount the rear axle hub in a soft jaw vise.
NOTICE:
Replace the axle hub assembly if it is dropped or a strong
shock is given to it.
(b) Using a pin punch and hammer, drive out the 2 pins and
remove the 2 attachments from SST.
(c) Using SST and 2 bolts (Diameter: 12 mm, pitch: 1.5 mm),
remove the skid control sensor from the rear axle hub.
SST 09520- 00031 (09520- 00040), 09521- 00020,
09950-00020
NOTICE:

If a damage is inflicted to the sensor rotor, replace the
axle hub assembly.

Do not scratch the contacting surface of axle hub and
speed sensor.
7. INSTALL SKID CONTROL SENSOR
(a) Clean the contacting surface of the axle hub and a new
skid control sensor.
NOTICE:
Make sure the sensor rotor is clean.
(b) Place the speed sensor on the axle hub so that the con-
nector is positioned, as shown in the illustration.
(c) Using SST and a press, install the skid control sensor to
the axle hub.
NOTICE:

Do not tap the skid control sensor with a hammer di-
rectly.

Check that the skid control sensor detection part is
clean.

Press in the skid control sensor straight and slowly.
SST 09830- 36010, 09950- 60010 (09951- 00650),
09950-70010 (09951-07100)

300M6-02
C91612
C83023
F40153
SST
- DRIVE SHAFT / PROPELLER SHAFTFRONT AXLE HUB SUB-ASSY LH (From July, 2003)
30-19
2422 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
FRONT AXLE HUB SUB-ASSY LH (From July, 2003)
REPLACEMENT
HINT:

Replace the RH side using the same procedures as for the LH side.
1. REMOVE FRONT WHEEL
2. REMOVE FRONT AXLE HUB LH NUT (SEE PAGE 30-8)
SST 09930-00010
3. DISCONNECT SPEED SENSOR FRONT LH (SEE PAGE 30-8)
4. SEPARATE FRONT DISC BRAKE CALIPER ASSY LH
(a) Remove the 2 bolts and separate the front disc brake cali-
per assy LH from the steering knuckle LH.
NOTICE:
Use a string or other device to keep the brake caliper from
hanging down by the flexible hose.
5. REMOVE FRONT DISC
6. SEPARATE TIE ROD ASSY LH (SEE PAGE 30-8)
SST 09628-6201 1
7. SEPARATE FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 LH (SEE PAGE 30-8)
8. REMOVE FRONT AXLE ASSY LH
(a) Using a plastic hammer, separate the front drive shaft
assy LH from the front axle hub sub-assy LH.
NOTICE:
Be careful not to damage the boot and speed sensor rotor.
(b) Remove the 2 bolts, nuts and steering knuckle with the
axle hub.
9. REMOVE LOWER BALL JOINT ASSY FRONT LH
(a) Remove the cotter pin and nut.
(b) Using SST, remove the lower ball joint assy front LH.
SST 09628-6201 1

Lexus Supports ASE CertificationPage 1 of 2
Title:
WHEEL FILM FOR BRAKE ROTOR
RUST PREVENTION
Models:
All Models with Wheel Film
Technical Service
Information Bulletin
July 16, 2004
PD001-04
To prevent brake rotor rust from forming during transportation and storage, wheel film will
be adopted instead of using a cardboard type anti±rust cover.
The purpose of the wheel film is to protect the disc brake rotor from weather elements
and initial rust before the vehicle is delivered to the customer. Consequently, the film
should remain on the wheel as long as possible.
NOTE:
Retain the wheel film on the disc wheel during vehicle display and storage.
Do not remove the wheel film right away at Pre±Delivery Service (PDS) if the vehicle
will be stored after PDS.
Remove the wheel film just prior to delivery to customers.
Wheel FilmFeatures of Wheel Film:
Material: Polyethylene
Color: Transparent
All Models with wheel film.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
PRE±DELIVERY SERVICE
Introduction
Applicable
Vehicles
Warranty
Information

WHEEL FILM FOR BRAKE ROTOR RUST PREVENTION ± PD001-04 July 16, 2004
Page 2 of 2
Firmly hold the outer end of the wheel film to pull it off.
NOTE:
If film adhesive residue is found on the disc wheel, remove it with a soft
cloth dipped in ethyl alcohol (ethanol). Do not use thinner to remove the
adhesive residue.
When the wheel film is removed below an ambient temperature of 0
C (32
F), it is
possible that the film may tear. For ease of film removal in cold conditions, please
warm the film above 0
C (32
F) using one of the following methods:
± Splash (hot) water on the wheel film.
± Warm wheel film with cotton cloth soaked in hot water.
± Warm wheel film with heat gun. Be sure not to overheat the film and wheel.
± Warm wheel film by infrared heater (lamp) for paint. Be sure not to overheat
the film and wheel.
± Warm wheel film by steam car wash.
± Park vehicle indoors (e.g. garage, etc.) for an extended period of time.
Please follow local laws for disposal. Polyethylene film will not generate harmful gasses
when it is burned.
MODEL(FRONT &PLANT20032004(FRONT &REAR)PLANT123456789101112123456789101112
GS 430/300Beginning January 2005
GX 470JAPANBeginning January 2005
LX 470Beginning January 2005
RX 330TMMCRX 330
JAPANSC 430JAPAN
This is a tentative schedule. There is a possibility that the introduction timing may be delayed on some models.
Removal
Procedure
Disposal
Procedure
Introduction
Schedule