C83051
D31341Dimension B
B
D30511D31482
AA
A
A
BA
CC
D30472
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E)
40-13
2528 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
19. INSTALL TORQUE CONVERTER CLUTCH ASSY
(a) Install the torque converter clutch to the automatic trans-
axle.
(b) Using vernier calipers, measure dimension ºAº between
the transaxle fitting part and the converter fitting part of
the drive plate.
(c) Using vernier calipers and a straight edge, measure di-
mension ºBº shown in the illustration and check that ºBº
is greater than ºAº measured in (b).
Standard: A + 1 mm or more
NOTICE:
Do not add the thickness of the straight edge.
20. INSTALL AUTOMATIC TRANSAXLE ASSY
(a) Install the automatic transaxle and 8 bolts to the engine.
Torque:
Bolt A: 64 NVm (653 kgfVcm, 47 ftVlbf)
Bolt B: 46 NVm (470 kgfVcm, 34 ftVlbf)
Bolt C: 37 NVm (377 kgfVcm, 27 ftVlbf)
(b) Apply a few drops of adhesive to each 2 threads on the
tip of the 6 torque converter clutch mounting bolts.
Adhesive: Part No. 08833-00070, THREE BOND 1324
or equivalent
(c) Install the 6 torque converter clutch mounting bolts.
Torque: 41 NVm (418 kgfVcm, 30 ftVlbf)
HINT:
First install green colored bolt, and then install the other 5 bolts.
F41698
Pedal Free play
R00934
Pedal Reserve
Distance
- BRAKEBRAKE PEDAL SUPPORT ASSY
32-9
2443 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
2. CHECK PEDAL FREE PLAY
(a) Stop the engine and depress the brake pedal several
times until there is no more vacuum left in the booster.
(b) Push in the pedal until the beginning of the resistance is
felt. Measure the distance, as shown.
Pedal free play: 1 - 6 mm (0.04 - 0.24 in.)
If incorrect, check the stop lamp switch clearance.
If the clearance is OK, then troubleshoot the brake system.
Stop lamp switch clearance:
0.5 - 2.5 mm (0.020 - 0.098 in.)
3. CHECK PEDAL RESERVE DISTANCE
(a) Release the parking brake pedal.
With engine running, depress the pedal and measure the
pedal reserve distance, as shown.
Pedal reserve distance from asphalt sheet at 490 N
(50 kgf, 110.2 lbf): More than 70 mm (2.76 in.)
If incorrect, troubleshoot the brake system.
F42718
Pedal Free Play
R00934
Pedal Reserve
Distance
- BRAKEACCELERATOR & BRAKE PEDAL ASSY (From August,
2002)32-13
2447 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
2. CHECK PEDAL FREE PLAY
(a) Stop the engine and depress the brake pedal several
times until there is no more vacuum left in the booster.
(b) Push in the pedal until the beginning of the resistance is
felt. Measure the distance, as shown.
Pedal free play: 1 - 6 mm (0.04 - 0.24 in.)
If incorrect, check the stop lamp switch assy clearance.
If the clearance is OK, then troubleshoot the brake system.
Stop lamp switch clearance:
0.5 - 2.5 mm (0.020 - 0.098 in.)
3. CHECK PEDAL RESERVE DISTANCE
(a) Release the parking brake pedal.
With engine running, depress the pedal and measure the
pedal reserve distance, as shown.
Pedal reserve distance from asphalt sheet at 490 N
(50 kgf, 110.2 lbf): More than 63 mm (2.48 in.)
If incorrect, troubleshoot the brake system.
3203F-08
BR2238
GOOD NO GOOD
2nd3rd
1st
BR2237
C16481
Ventilation
No Ventilation 32-26
- BRAKEBRAKE BOOSTER ASSY
2460 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
BRAKE BOOSTER ASSY (From July, 2003)
ON-VEHICLE INSPECTION
1. INSPECT BRAKE BOOSTER
(a) Air tightness check.
(1) Start the engine and stop it after 1 or 2 minutes. De-
press the brake pedal several times slowly.
HINT:
If the pedal goes down farthest the 1st time, but gradually rises
after the 2nd or 3rd time, the booster is air tight.
(2) Depress the brake pedal while the engine is run-
ning, and stop the engine with the pedal depressed.
HINT:
If there is no change in the pedal reserve distance after holding
the pedal for 30 seconds, the booster is air tight.
(b) Operating check.
(1) Depress the brake pedal several times with the igni-
tion switch OFF and check that there is no change
in the pedal reserve distance.
(2) Depress the brake pedal and start the engine.
HINT:
If the pedal goes down slightly, operation is normal.
2. INSPECT VACUUM CHECK VALVE
(a) Check vacuum check valve.
(1) Slide the clip and disconnect the vacuum hose.
(2) Remove the vacuum check valve.
(3) Check that there is ventilation from the booster to
engine, and no ventilation from the engine to the
booster.
(4) If any fault is found, replace the vacuum check
valve.
320E1-02
- BRAKEBRAKE ACTUATOR ASSY (W/O VSC)
32-47
2481 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
BRAKE ACTUATOR ASSY (W/O VSC)
ON-VEHICLE INSPECTION
1. CONNECT HAND-HELD TESTER:
(a) Connect the hand-held tester to the DLC3.
(b) Start the engine and run it at idle.
(c) Select the ACTIVE TEST mode on the hand-held tester.
HINT:
Please refer to the hand-held tester operator's manual for further details.
2. INSPECT ACTUATOR MOTOR OPERATION
(a) With the motor relay ON, check the actuator motor operation noise.
(b) Turn the motor relay OFF.
(c) Depress the brake pedal and hold it for about 15 seconds. Check that the brake pedal cannot be de-
pressed.
(d) With the motor relay ON, check that the pedal does not pulsate.
NOTICE:
Do not keep motor relay ON for more than 5 seconds continuously. When operating it continuously,
set the interval of more than 20 seconds.
(e) Turn the motor relay OFF and release the brake pedal.
3. INSPECT RIGHT FRONT WHEEL OPERATION
NOTICE:
Never turn ON the solenoid which is not described below.
(a) With the brake pedal depressed, perform the following operations.
(b) Turn the SFRH and SFRR solenoid ON simultaneously, and check that the pedal cannot be depressed.
NOTICE:
Do not keep solenoid ON for more than 10 seconds continuously. When operating it continuously,
set the interval of more than 20 seconds.
(c) Turn the SFRH and SFRR solenoid OFF simultaneously, and check that the pedal can be depressed.
(d) Turn the motor relay ON, and check that the pedal returns.
NOTICE:
Do not keep motor relay ON for more than 5 seconds continuously. When operating it continuously,
set the interval of more than 20 seconds.
(e) Turn the motor relay OFF and release the brake pedal.
4. INSPECT OTHER WHEEL OPERATION
(a) As in the same procedure, check the solenoids of other wheels.
HINT:
Left front wheel: SFLH, SFLR
Right rear wheel: SRRH, SRRR
Left rear wheel: SRLH, SRLR
3203J-09
32-50
- BRAKEBRAKE ACTUATOR ASSY (W/VSC)(From July, 2003)
2484 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
BRAKE ACTUATOR ASSY (W/VSC)(From July, 2003)
ON-VEHICLE INSPECTION
1. CONNECT HAND-HELD TESTER:
(a) Connect the hand-held tester to the DLC3.
(b) Start the engine and run it at idle.
(c) Select the ACTIVE TEST mode on the hand-held tester.
HINT:
Please refer to the hand-held tester operator's manual for further details.
2. INSPECT ACTUATOR MOTOR OPERATION
(a) With the motor relay ON, check the actuator motor operation noise.
(b) Turn the motor relay OFF.
(c) Depress the brake pedal and hold it for about 15 seconds. Check that the brake pedal cannot be de-
pressed.
(d) With the motor relay ON, check that the pedal does not pulsate.
NOTICE:
Do not keep motor relay ON for more than 5 seconds continuously. When operating it continuously,
set the interval of more than 20 seconds.
(e) Turn the motor relay OFF and release the brake pedal.
3. INSPECT RIGHT FRONT WHEEL OPERATION
NOTICE:
Never turn ON the solenoid which is not described below.
(a) With the brake pedal depressed, perform the following operations.
(b) Turn the SFRH and SFRR solenoid ON simultaneously, and check that the pedal cannot be depressed.
NOTICE:
Do not keep solenoid ON for more than 10 seconds continuously. When operating it continuously,
set the interval of more than 20 seconds.
(c) Turn the SFRH and SFRR solenoid OFF simultaneously, and check that the pedal can be depressed.
(d) Turn the motor relay ON, and check that the pedal returns.
NOTICE:
Do not keep motor relay ON for more than 5 seconds continuously. When operating it continuously,
set the interval of more than 20 seconds.
(e) Turn the motor relay OFF and release the brake pedal.
4. INSPECT OTHER WHEEL OPERATION
(a) As in the same procedure, check the solenoids of other wheels.
HINT:
Left front wheel: SFLH, SFLR
Right rear wheel: SRRH, SRRR
Left rear wheel: SRLH, SRLR
141C0-02
A82940
Vane Pump
CrankshaftGenerator Measuring Points for Belt Deflection
or Tension
Compressor
- ENGINE MECHANICALENGINE (3MZ-FE)
14-1
2093 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
ENGINE (3MZ-FE)
INSPECTION
1. INSPECT ENGINE COOLANT (See page 16-1)
2. INSPECT ENGINE OIL
3. INSPECT BATTERY
Standard specific gravity: 1.25 to 1.29 at 20C (68F)
4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSY
5. INSPECT SPARK PLUG (See page 18-3)
6. INSPECT V-RIBBED BELT
(a) Belt deflection:
Pressing force: 98 N (10 kgf, 22 lbf)
New Belt
mm (in.)Used Belt
mm (in.)
V-ribbed Belt
(For fan and generator)9.1 to 10.5
(0.358 to 0.413)11 to 13.5
(0.433 to 0.531)
V-ribbed Belt
(For vane pump)8 to 10
(0.315 to 0.394)11 to 14
(0.433 to 0.551)
(b) Belt tension:
New Belt
N (kg , lb)Used Belt
N (kg , lb)
V-ribbed Belt
(For fan and generator)637 to 735
(65 to 75 , 143 to 165)392 to 588
(40 to 60 , 88 to 132)
V-ribbed Belt
(For vane pump)588 to 686
(60 to 70 , 132 to 154)245 to 392
(25 to 40 , 55 to 88)
NOTICE:
Check the drive belt deflection at the specified point.
When installing a new belt, set its tension value as
specified.
When inspecting a belt which is used for over 5 min-
utes, apply the specification of ºUsed beltº.
When reinstalling a belt which is used for over 5 min-
utes, adjust its belt deflection and tension to the inter-
mediate value of each specification in ºUsed beltº.
The V- ribbed belt tension and deflection value
should be checked after 2 revolutions of engine
cranking.
When using a belt tension gauge, confirm the accura-
cy first by using a master gauge.
7. INSPECT IGNITION TIMING
(a) Warm up engine.
(b) When using the hand-held tester or OBD II scan tool:
(1) Connect the hand-held tester or OBD II scan tool
to the DLC3.
(2) Enter DATA LIST MODE on the hand-held tester or
OBD II scan tool.
Ignition timing: 8 to 12 BTDC
HINT:
Refer to the hand-held tester or OBD II scan tool operator's
manual if you need help to select DATA LIST.
A85669
TC
CG
A82935
Tester TerminalEngine Wire 14-2
- ENGINE MECHANICALENGINE (3MZ-FE)
2094 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(c) When not using the hand-held tester or OBD II scan tool:
(1) Using SST, connect terminals 13 (TC) and 4 (CG)
of the DLC3.
SST 09843-18040
NOTICE:
Make sure of the terminal numbers before connecting
them. Connecting wrong terminals can damage the
engine.
Turn OFF all electrical systems before connecting the
terminals.
Perform this inspection after the cooling fan motor is
turned OFF.
(2) Remove the V-bank cover.
(3) Pull out the engine wire colored by black and red as
shown in the illustration.
(4) Connect the tester terminal of the timing light to the
engine.
NOTICE:
Use a timing light which detects the first signal.
(5) Inspect the ignition timing at idle.
Ignition timing: 8 to 12 BTDC
NOTICE:
When checking the ignition timing, the transmission is in
the neutral position.
HINT:
Run the engine at 1,000 to 1,300 rpm for 5 seconds, then check
that the engine speed returns to the idle speed.
(6) Disconnect terminals 13 (TC) and 4 (CG) of the
DLC3.
(7) Inspect the ignition timing at idle.
Ignition timing: 7 to 24 BTDC
(8) Confirm that the ignition timing advances when the
engine speed is increased.
(9) Remove the timing light.
8. INSPECT ENGINE IDLE SPEED
(a) Warm up the engine.
(b) When using the hand-held tester or OBD II scan tool:
(1) Connect the hand-held tester or OBD II scan tool to the DLC3.
(2) Enter DATA LIST MODE on the hand-held tester or OBD II scan tool.
Idle speed: 630 to 730 rpm
NOTICE:
When checking the idle speed, the transmission is in the neutral position.
Check the idle speed with the cooling fan OFF.
Switch OFF all accessories and air conditioning before connecting the hand-held tester or OBD
II scan tool.
HINT:
Refer to the hand-held tester or OBD II scan tool operator's manual for further details.