2005 LEXUS ES300 license plate

Lexus Supports ASE CertificationPage 1 of 9
Title:
PRE-DELIVERY SERVICE (PDS)
INFORMATION FOR ES 330
Models:
'04 ES 330
Technical Service
Information Bulletin
August 26, 2003
PD002-03
The following items need to be performed during Pre±Delivery Service (PDS) on
2004 model year ES 330 vehicles.
2004 model year ES 330 vehicles.
ITEM NO.SUBJECTPAGE
1D.C.C. Fuse Installation During PDS2
2Removal of Front Emergency Towing Eyelet and Installation
of Towing Eyelet Hole Cover (Performed at Port)3
3Front License Plate Mounting Bracket Installation4
4Initialization of Moon Roof5
5Initial Calibration of Compass6
6Installation of Rubber Body Plugs9
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
PRE±DELIVERY SERVICE
Introduction
Applicable
Vehicles
Contents
Warranty
Information

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 4 of 9
FRONT LICENSE PLATE MOUNTING BRACKET INSTALLATION
The front license plate bracket and two self tapping screws are included in the
luggage compartment.
1. Aligning the holes ªAº of the mounting
bracket with the dimples on the front
bumper cover, mark the location of the
holes ªBº on the front bumper cover.
NOTE:
Holes ªAº are used for installation
of the mounting bracket to the
bumper cover.
Holes ªBº are used for installation
of the front license plate to the
mounting bracket.
2. Drill two relief holes with a diameter of
12 mm (0.47 in.) at the marks on the
front bumper cover to prevent the
license plate retaining bolt end from
contacting the cover.
NOTE:
Do not drill the dimples on the front
bumper cover.
3. Install the mounting bracket to the
front bumper cover using the two self
tapping screws.
Install the front license plate to the
mounting bracket using bolts of the
following dimensions:
Length: less than 25 mm (0.98 in.)
Diameter: 6.0 mm (0.24 in.)
Pitch: 1.0 mm (0.04 in.) ITEM NO. 3:
Introduction
Installation
Procedure
Mark And Drill Holes
Dimples
Mounting Bracket
AA B B
Tapping Screws

Lexus Supports ASE CertificationPage 1 of 2
Title:
FRONT LICENSE PLATE MOUNTING
BRACKET INSTALLATION
Models:
'05 ± '06 ES 330
Technical Service
Information Bulletin
August 25, 2005
PD036-05
The ES 330 front license plate mounting bracket and two self-tapping screws are
placed in the luggage compartment of the vehicle at the assembly plant. For states
that require a front license plate, install the bracket and bolts on the bumper cover
during Pre-Delivery Service (PDS) according to the following procedure.
2005 ± 2006 model year ES 330 vehicles.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
1. Aligning the holes ªAº of the mounting
bracket with the dimples on the front
bumper cover, mark the location of the
holes ªBº on the front bumper cover.
NOTE:
Holes ªAº are used for installation
of the mounting bracket to the
bumper cover.
Holes ªBº are used for installation
of the front license plate to the
mounting bracket.
2. Drill two relief holes with a diameter of
12 mm (0.47 in.) at the marks on the
front bumper cover to prevent the
license plate retaining bolt end from
contacting the cover.
NOTE:
Do not drill the dimples on the front
bumper cover.
PRE-DELIVERY SERVICE
Introduction
Applicable
Vehicles
Warranty
Information
Installation
Procedure
Mark and Drill Holes
Dimples
Mounting Bracket
AA B B

FRONT LICENSE PLATE MOUNTING BRACKET INSTALLATION ± PD036-05 August 25, 2005
Page 2 of 2
3. Install the mounting bracket to the
front bumper cover using the two
self-tapping screws.
4. Install the front license plate to the
mounting bracket using bolts of the
following dimensions:
Length: Less than 25 mm (0.98 in.)
Diameter: 6.0 mm (0.24 in.)
Pitch: 1.0 mm (0.04 in.) Installation
Procedure
(Continued)
Tapping Screws