2005 CITROEN C6 suspension

Downloaded from www.Manualslib.com manuals search engine 151
AXLES
SUSPENSION
STEERING
SUSPENSION: TIGHTENING TORQUES10 Front pivot lower balljoint on Pivot support 6,5 ± 0,911 Front pivot lower balljoint on Pivot support 17 ± 1,712 Steering rack balljoint on Front pivot 3,5 ± 0,313 Rear fixing of suspension lower arm on Front subframe 11 ± 1,114 Rear fixing of suspension lower arm on Front subframe 6,5 ± 0,615 Fixing of front anti-roll bar bearing on Front subframe 4,5 ± 0,4
B3CP09WDB3CP09FC
Angl-C6-page121-169-2005 4/02/05 17:31 Page 151

Downloaded from www.Manualslib.com manuals search engine 152
AXLES
SUSPENSION
STEERING
SUSPENSION: TIGHTENING TORQUES16 Fixing of suspension lower arm support on Front subframe 8 ± 0,817 Front fixing of suspension lower arm on Front subframe 12,3 ± 1,2
B3CP09XD
Angl-C6-page121-169-2005 4/02/05 17:31 Page 152

Downloaded from www.Manualslib.com manuals search engine 153
AXLES
SUSPENSION
STEERING
SUSPENSION: TIGHTENING TORQUES
Rear suspension
18 Tracking adjustment rod on Rear pivot
19 Lower fixing of rear suspension cylinder on Rear pivot
7 ± 0,7
20 Suspension longitudinal arm on Rear pivot
21 Suspension lower arm on Rear pivot22 Rear anti-roll bar bearing on Body 7,5 ± 0,7
23 Suspension lower arm on Rear axle crossmember
7 ± 0,724 Tracking adjustment rod on Rear axle crossmember25 Screw for locking of tracking adjustment rod 1 ± 0,2
Suspension longitudinal arm on Body
26Pre-tightening3,3 ± 0,3
Angular tightening 150° ± 5°
27 Suspension upper arm on Rear pivot
28 Suspension upper arm on Rear axle crossmember 7 ± 0,7
29 Upper fixing of rear suspension cylinder on Rear axle crossmember
B3DP0CQDB3DP0CPD
Angl-C6-page121-169-2005 4/02/05 17:31 Page 153

Downloaded from www.Manualslib.com manuals search engine 154
AXLES
SUSPENSION
STEERING
SUSPENSION: TIGHTENING TORQUES
Rear suspension
30 Upper fixing of rear anti-roll bar rod on Rear pivot
31 Lower fixing of rear anti-roll bar rod on Rear anti-roll bar 4 ± 0,632 Fixing of rear anti-roll bar half-bearing 1,8 ± 0,4
B3DP0CRD
Angl-C6-page121-169-2005 4/02/05 17:31 Page 154

Downloaded from www.Manualslib.com manuals search engine 155
AXLES
SUSPENSION
STEERING
Tools.
[1]Pliers for clic clips: 4121-T
[2] LEXIAdiagnostic tool: 4171-T
[3] PROXIAdiagnostic tool: 4165-T
Draining.
Start the engine.
Place the vehicle in the low position.
Stop the engine.
Raise and support the vehicle, wheels hanging.
WARNING: The LDS fluid reservoir is pressurised.
Open the cap of the LDSfluid reservoir.
Remove:
- The front RH wheel.
- The front RH splash-shield.
Remove the clip (1) using tool [1].
Uncouple the hose (2)from the LDSfluid reservoir.
Drain the LDSfluid reservoir.
IMPERATIVE: Any LDS fluid recovered must not be re-used.
B3FP7HED
DRAINING, FILLING AND BLEEDING THE HYDRAULIC SUSPENSION/STEERING CIRCUIT
Angl-C6-page121-169-2005 4/02/05 17:31 Page 155

Downloaded from www.Manualslib.com manuals search engine 156
AXLES
SUSPENSION
STEERING
Filling.
Couple the hose (2)on the LDSfluid reservoir.
Refit:
- The clip (1).
- The front RH splash-shield.
- The front RH wheel.
Lower the vehicle.
"a"maximum level for the LDSfluid
Fill the LDSfluid reservoir up to the maximum level for the LDSfluid "a".
B3FP7HFD
DRAINING, FILLING AND BLEEDING THE HYDRAULIC SUSPENSION/STEERING CIRCUIT
Angl-C6-page121-169-2005 4/02/05 17:31 Page 156

Downloaded from www.Manualslib.com manuals search engine 157
AXLES
SUSPENSION
STEERING
Bleeding.
Connect tool [2]or [3]to the vehicle's diagnostic socket.
Switch on the ignition.
Perform a global test.
Go into the menu:
- Variable damping.
- Bleeding the suspension circuit.
Follow the instructions on the screen.
Apply a pressure of 0.5 barin the LDSfluid reservoir (using a tool FACOM 920).
Start the engine.
Wait for the vehicle height to stabilise.
Place the vehicle in the high position.
Place the vehicle in the low position.
Move the steering in each direction, from lock to lock.
Stop the engine.
Check the LDSfluid level.
B3FP7HGD
DRAINING, FILLING AND BLEEDING THE HYDRAULIC SUSPENSION/STEERING CIRCUIT
Angl-C6-page121-169-2005 4/02/05 17:31 Page 157

Downloaded from www.Manualslib.com manuals search engine 158
AXLES
SUSPENSION
STEERING
Checking and topping up the LDS fluid level.
NOTE:Checking the LDSfluid level is done with the vehicle in the forced low position
(hydraulic suspension circuit depressurised).
"a"Maximum level for the LDSfluid
"b"Minimum level for the LDSfluid
Open the cap (3).
If necessary, add LDSfluid up to the maximum level "a".
IMPERATIVE: A container of LDS that has been opened must be sealed and kept in a
clean place. A container of LDS has to be used up within two weeks of opening, after
which any unused LDS fluid must be disposed of.
B3FP7HGD
DRAINING, FILLING AND BLEEDING THE HYDRAULIC SUSPENSION/STEERING CIRCUIT
Angl-C6-page121-169-2005 4/02/05 17:31 Page 158