2005 CITROEN C6 suspension

Downloaded from www.Manualslib.com manuals search engine 31
ENGINE
TIGHTENING TORQUES: POWER UNIT SUSPENSION
Gearbox impact absorber
18 Screws 4 ± 0,6
Driveshaft bearing
19 Screws 6 ± 0,6Engine: DT17BTED4
B2CP45ECB2CP45DC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 31

Downloaded from www.Manualslib.com manuals search engine 114
CLUTCH
GEARBOX
TRANSMISSION
DRAINING, FILLING AND TOPPING UP THE AM6 AUTOMATIC GEARBOX
Tool.
[1] Filling cylinder: (-).0340
Respect the safety and cleanliness requirements.
Draining.
IMPERATIVE: Draining of the gearbox must be done with the oil hot (60°C minimum), in order to
ensure that the impurities in suspension in the oil are eliminated.
NOTE:Drainage is only partial, as the torque converter cannot be drained totally.
Raise the vehicle.
Remove:
- The oil level plug (2)by means of the Torx spanner.
- The drain plug (1)using a hexagonalspanner.
NOTE :Around 3 litresof oil should flow out.
Filling.
Fit the drain plug (1)(with a new seal).
Tighten the plug (1)to: 5 ± 1 mdaN.
Remove:
- The air filter housing.
- The oil filler plug (3).
Use tool [1].
B2CP3WZCB1BP317C
Angl-C6-page101-120-2005 4/02/05 17:25 Page 114

Downloaded from www.Manualslib.com manuals search engine 121
AXLES
SUSPENSION
STEERING
WHEEL AND TYRES
Engine plate
Tyre/circumference S
Type
WheelT
A
Name of rim
Normal operating pressure:
front/rear
Pressure for maximum load :
front/rear
Pressure: loaded, high speed:
front/rear
Tyre S
Spare wheel T
Normal operating pressure
Pressure for maximum load
Pressure: loaded, high speed 3.0i 24S 2,7 24V
XFV UHZ
225/55 R17 97W/2,071 m 245/45 R18 100W/2,065m 245/45 R18 100W/2,065m
Michelin PRIMACY
7 J17-CH5-32 8 J18-CH5-33 8 J18-CH5-33
SATURNE SAN MARIN 2 SAN MARIN 2
2,4/2,4 2,4/2,4 2,4/2,4
2,6/2,6 2,4/2,4 2,6/2,6
2,4/2,4 2,4/2,4 2,6/2,6
225/55 R17 97W
7 J17-5-32
2,6 2,4 2,6
2,6 2,4 2,6S =Standard fitting.T =Steel wheel.A=Alloy wheel.
NOTE:The label indicating the recommended tyre pressures is affixed to the front LH door pillar.
Angl-C6-page121-169-2005 4/02/05 17:31 Page 121

Downloaded from www.Manualslib.com manuals search engine 122
AXLES
SUSPENSION
STEERING
WHEEL AND TYRESNOTE:The label indicating the recommended tyre pressures is affixed to the front
LH door pillar.
«a»Recommended tyre inflation pressures (empty and under load)
«b»Tyre specifications
«c»Type of tyres
«d»Recommended inflation pressure for the spare wheel
B2GP01FD
Identification of inflation pressures
Angl-C6-page121-169-2005 4/02/05 17:31 Page 122

Downloaded from www.Manualslib.com manuals search engine 123
AXLES
SUSPENSION
STEERING
WHEEL AND TYRES(1)Wheel bolt (all rim types)
(2)Light alloy wheel
(3)Steel aluminium wheel
NOTE:If mixed fixing bolts are fitted on steel wheels, the shoulders of the bolts
remain free.
Tightening torques for the wheel bolts.
9 ± 1 m.daN
B2GP00JD
Identification of the wheel bolts
Angl-C6-page121-169-2005 4/02/05 17:31 Page 123

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
124
WHEEL AND TYRES(4)Valve(8)Seal
(5)Antenna(9)Cap
(6)HF transmitter unit(10)Nut
(7)Washer
Composition.
A SIEMENS HFtransmitter module (6) integral to each wheel in the place of the
valve, each including a lithium battery.
An HFreceiver in the communication module under the dashboard.
WARNING: Each time a tyre is replaced, it is necessary to replace the valve (4).
WARNING: Each time a wheel rim is replaced, it is necessary to replace the
seal (8).
WARNING: Each time a transmitter module is changed, it is necessary to have
the replacement recognised by the deflation detection ECU, using a diagnostic
tool.
B2GP01ND
Deflation detection system
Angl-C6-page121-169-2005 4/02/05 17:31 Page 124

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
125
CHECKING AND ADJUSTING VEHICLE HEIGHT
IMPERATIVE: Respect the safety and cleanliness requirements.
Tools.
[1]Gauge for measuring radius of wheels (5 bolts): 9801-T
[2]Gauge for height under bodyshell: 2305-T
[3] LEXIAstation: 4171-T
[4] PROXIAstation: 4165-T
Preliminary operations.
Check the tyre pressures.
Place the vehicle on a 4 column lift.
Switch on the ignition.
Release the parking brake.
Put the vehicle in the high position.
Put the vehicle in the normal height position (driving height).
During:During the measuring, do not move the vehicle.
Reference heights: REFERENCE = Ignition switched on
Angl-C6-page121-169-2005 4/02/05 17:31 Page 125

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
126 Place the tool [1]on the wheel
fixing bolts.
Measure the wheel radiuses
using tool [2].
Measure, using tool [2].
The front LHheight H1M: Measure between the ground and zone Aunder the front subframe.
The front RHheight H2M: Measure between the ground and zone Bunder the front subframe.
CHECKING AND ADJUSTING VEHICLE HEIGHT
Warning: During measurement of reference heights: Do not switch off the ignition
Measuring the front heights
Measuring the front wheel radiusesB3CP0AQD
B3CP0ARD
B3CP0ASD
Reference heights: REFERENCE = Ignition switched on
Angl-C6-page121-169-2005 4/02/05 17:31 Page 126