2005 Acura RSX Owner's Manual

Vents, Heating, and A/C
88
TEMPERATURE CONTROL DIALMODE CONTROL DIAL
REAR WINDOW DEFOGGER BUTTON
RECIRCULATION BUTTON AIR CONDITIONING BUTTON FAN CONTROL DIAL

To use the heating and cooling
system in automatic mode, set the
system as f ollows.Set the f an control dial to AUTO.
Set the mode control dial to AUTO.
Turn the temperature control dial
to the desired temperature.
Select Fresh Air mode by pressing
the Recirculation button. The
indicator in the switch should be
off.
Turn on the A/C by pressing the
button. Pressing the A/C button turns the
air conditioning ON and OFF. The
indicator in the button comes on
when the A/C is ON.
When you turn the A/C of f , the
system cannot regulate the inside
temperature if you set the dial below
the outside air temperature.
With A/C on, use the temperature
control dial to adjust the temperature
of the air f low to a comf ortable
setting.
Air conditioning also removes mois-
ture from the air as it operates. You
canuseittodefogthewindows
quickly in cool or damp weather.
Used in combination with the heater,
it also makes the interior warm and
dry.
To heat or cool the interior f aster,
select Recirculation mode and set
the temperature control dial to the
upper or lower limit. The system
runs on f ull cooling or heating only.
It does not regulate the interior temperature. When the temperature
is set between the lower and upper
limits, the system regulates the
interior temperature to the set value.
TurningthefancontroldialtoOFF
shuts the heating and cooling system
completely off. Keep the system
completely of f only f or short periods.
To keep stale air and mustiness from
collecting, you should have the f an
running at all times.
You can manually set the system
controls f or ventilation, air
conditioning, heating, air f low
direction, and fan speed in various
combinations.
1.
2.
3.
4.
5.
CONT INUED
Vents, Heating, and A/C
Automatic Operation
Manual OperationA ir Condit ioning But t on
Features
89

Air conditioning places an extra load
on the engine. Watch the engine
coolant temperature gauge (see page) when using the A/C in heavy
traf f ic or driving up long hills. If it
moves near the red zone, turn of f the
air conditioning until the gauge
reads normally.
This button controls the source of air
going into the system. When the
indicator in this button is on, the
system is recirculating the interior
air (Recirculation mode). When the
indicator is of f , f resh air is brought
in f rom outside the vehicle (Fresh
Air mode). Push the button to
change between recirculated and
f resh air. Use Recirculation mode to heat or
cool the interior more quickly, or to
keep out smoke and dust. Leaving
the system in the Recirculation mode
with the A/C off can cause the
windows to fog up. Switch to Fresh
Air mode as soon as the interior
reaches a comf ortable temperature
or the outside smoky, dusty condi-
tion clears.
You can manually select the f an
speed by turning the f an speed
control dial. Turning this dial
clockwise increases the f an speed,
which increases air flow.
When the dial is set to AUTO, the
system controls the f an speed
automatically.
Use this dial to select the direction of
airf low coming out of the system.
Some air will come out of the side
vents in all modes.
In AUTO mode, the system controls
the air f low direction automatically
between the dashboard vents and
the f loor vents.
The main air flow comes out
of the dashboard vents.
The main air flow is directed
to the floor vents. Airf low is divided between
the vents in the dashboard and the
f loor vents.
The main air flow is divided
between the floor vents and
defroster vents at the base of the
windshield.
58
Vents, Heating, and A/C
Recirculat ion But t on
Fan SpeedMode Cont rol Dial
90

Theheatingandcoolingsystemhas
temperature sensors next to the
steering column and in the top of the
dashboard. Do not cover the sensors
or spill any liquid on them.
If there is actual frost on the win-
dows, f irst select the Recirculation
mode. If the windows are f ogged,
select the Fresh Air mode. Warmed
air will then flow from the wind-
shield and side def roster vents. The main air f low is directed
to the windshield for faster defrost-
ing or def ogging. To def rost or def og
more quickly, turn the temperature
control dial to maximum. Select , and set the f an speed to
high.
When you select or ,
the A/C turns on automatically to
help dehumidif y the air and def og
the windshield. When you select
another mode, the A/C stays on. If
you do not want to use the A/C in
that mode, press the button to turn it
off.
Vents, Heating, and A/C
T emperature Sensors
Features
91

Playing the Radio
T ype-S
A ll models except T ype-S
92
AM/FM BUTTON
SEEK/SKIP BAR PRESET BUTTONS TUNE/MODE KNOB STEREO INDICATOR
SCAN INDICATOR
SCAN BUTTON
AUTO SELECT BUTTON
TUNE/MODE KNOB
PRESET BUTTONS SCAN INDICATOR
STEREO INDICATOR
SCAN BUTTON
AUTO SELECT BUTTON FM BUTTON
SEEK BUTTONS
AM BUTTON
POWER/VOLUME KNOB
POWER/VOLUME KNOB

µ
µ µ´ µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pressing the
PWR/VOL knob, or the AM or FM
button. Adjust the volume by turning
the knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is broad-
castinginstereo.Stereo
reproduction on AM is not available.
You can use these five methods to
find radio stations on a selected
band: the
preset buttons, and .Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The SEEK f unction
searches up and down f rom the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
bar or ( )/( ) buttons, then
release it. The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds. If you do
nothing, the system will then scan
f or the next strong station and play it
f or 5 seconds. When it plays a station
that you want to listen to, press the
SCAN button again.
CONT INUED
Playing the Radio
To Play the Radio
To Select a Station
TUNE,SEEK,SCAN, AUTO SELECT TUNE
SEEK
SCAN
Features
93

µµEach preset button can
store one f requency on AM, and two
f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick a preset button, and hold it
until you hear a beep.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. If you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
Press the A. SEL button. ‘‘A.SEL’’
will f lash in the display, and the
system will go into scan mode f or
several seconds. It stores the
f requencies of six AM stations and
twelve FM stations in the preset
buttons.
You will see a ‘‘0’’ displayed af ter
pressing a preset button if Auto
Select cannot f ind a strong station
f or every preset button. If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind stations, then
store them in the preset buttons as
described previously.
press the
A. SEL button. This restores the
presets you originally set.
1.
2.
3.
4.
To turn of f Auto Select,
Playing the Radio
Preset
A UT O SEL ECT
94

µµ
Press the MODE (TUNE) knob
repeatedly to display the Bass (BAS),
Treble (TRE), Balance (BAL), and
Fader (FAD) setting.
Eachmodeisshowninthedisplayas
it changes. Turn the MODE (TUNE)
knob to adjust the setting to your
liking. When the level reaches the
center, you will see ‘‘C’’ in the display.
The system will automatically return
the display to the selected audio
mode about 5 seconds af ter you stop
adjusting a mode.
Use the TRE/BAS
modes to adjust the tone to your
liking. These two
modes adjust the strength of the
sound coming f rom each speaker.
BAL adjusts the side-to-side strength,
while FAD adjusts the f ront-to-back
strength.
You can use the instrument panel
brightness control knob to adjust the
illumination of the audio system (see
page ). The audio system
illuminates when the parking lights
are on, even if the radio is of f . 62
Playing the Radio
Adjusting the Sound
Treble/Bass Balance/Fader
A udio System L ighting
Features
95