2004 MITSUBISHI ENDEAVOR wiring

Q: Is the wiring harness between rear blower motor connector C-20
(terminal 1) and floor console rear A/C switch assembly connector C-19
(terminal 5) in good condition?

YES:
It can be assumed that this malfunction is intermittent.
Refer to
HOW TO USE TROUBLESHOOTING/INSPECTION
SERVICE POINTS
.
NO:
Repair the wiring harness. The rear blower motor should operate
normall
y.

2004 Mitsubishi Endeavor LS
2004 HVAC Automatic Air Conditioning - Endeavor

The rear blower motor should operate normally. NO:
Go to Step 5.
STEP 5. Check the wiring harness between resistor connector C-21
(terminal 1, 3 and 6) and floor console rear A/C switch assembl
y connector
C-19 (terminal 5, 1 and 6).

Q: Is the wiring harness between resistor connector C-21 (terminal 1, 3
and 6) and floor console rear A/C switch assembly connector C-19
(terminal 5, 1 and 6) in good condition?

2004 Mitsubishi Endeavor LS
2004 HVAC Automatic Air Conditioning - Endeavor

YES:
It can be assumed that this malfunction is intermittent.
Refer to
HOW TO USE TROUBLESHOOTING/INSPECTION
SERVICE POINTS
.
NO:
Repair the wiring harness. The rear blower motor should operate
normally.
DATA LIST REFERENCE TABLE DATA LIST REFERENCE

CHECK AT A/C-ECU TERMINAL SCAN TOOL
(MUT-III)
DISPLAY
ITEM NO.
INSPECTION
ITEM
INSPECTION
REQUIREMENT
NORMAL
VALUE
Inside
temperature
sensor
01
Interior
temperature
sensor
Ignition switch:
ON
Inside air
temperature
and
temperature
displayed on
the scan tool
are identical.
Photo sensor
06
Photo sensor
Ignition switch:
ON
Amount o
f
light is
proportional to
voltage
displayed on
the scan tool.
NOTE: For the data list items other than above, refer to DATA LIST REFERENCE TABLE
.

2004 Mitsubishi Endeavor LS
2004 HVAC Automatic Air Conditioning - Endeavor

2004 BODY & ACCESSORIES
Ignition Switch - Endeavor
IGNITION SWITCH GENERAL DESCRIPTION < UP TO DECEMBER 2003 > IGNITION KEY REMINDER TONE ALARM The ignition key reminder tone alarm will sound under the following condition, and
warn the driver to remove the ignition key.
The driver's door is opened when the ignition switch is at "LOCK" (OFF) or
"ACC" position without removing the ignition key.
However, the light reminder tone alarm will take precedence over this function.
DOOR LOCK PREVENTION FUNCTION If the key is left in the ignition switch while the driver's door opened or the assistant
door opened, all door are automatically unlock to prevent locking the ignition key
in the vehicle after door is locked. IMMOBILIZER SYSTEM The immobilizer system consists of the ignition key, the immobilizer-ECU with key
ring antenna, and the PCM. The ignition key has a built-in transponder. Only the
registered ignition key permits the engine to start, therefore, the engine can never be
started by means of a forged key or by connecting the ignition wiring directly. The
system is significantly safe and reliable against theft. In addition, the driver has only
to turn the ignition switch to the "ON" position to activate the immobilizer system.
If the requirements for starting the engine are not satisfied, the engine will be
immobilized. If a registered ignition key is lost, all your ignition keys need to be
registered again using scan tool MB991958 (MUT-III Sub Assembly) to ensure
security (Refer to ON
-VEHICLE SERVICE
). An additional ignition key can be
registered as follows (only if no ignition keys are lost):
Using scan tool MB991958 (MUT-III Sub Assembly) (Refer to ON
-
VEHICLE SERVICE
).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor


2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

means of a forged key or by connecting the ignition wiring directly. The system is
significantly safe and reliable against theft. In addition, the driver has only to turn
the ignition switch to the "ON" position to activate the immobilizer system. If the
requirements for starting the engine are not satisfied, the engine will be
immobilized. If a registered ignition key is lost, all your ignition keys need to be
registered again using scan tool MB991958 (MUT-III Sub Assembly) to ensure
security (Refer to ON
-VEHICLE SERVICE
). An additional ignition key can be
registered as follows (only if no ignition keys are lost):
Using scan tool MB991958 (MUT-III Sub Assembly) (Refer to ON
-
VEHICLE SERVICE
).
By operating two ignition keys that have been already registered (Refer toON
-
VEHICLE SERVICE
).
OPERATION 1. When the ignition switch is turned to "ON" position, the PCM sends a
requirement for the encrypted code to the immobilizer-ECU (at this time, the
engine is remobilized).
2. When the immobilizer-ECU receives the requirement from the PCM, the
immobilizer-ECU supplies power to the transponder inside the ignition key via
the antenna. The energized transponder sends the encrypted code back to the
immobilizer-ECU via the antenna.
3. The immobilizer-ECU judges the encrypted code with its code logic in itself. If
they are identical, the immobilizer-ECU sends the encrypted code to the PCM.
4. If the PCM can not receive the encrypted code, the engine will be immobilized.
Fig. 3: Identifying Immobilizer System Operation Diagram
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
CAUTION WHEN REPLACING IMMOBILIZER SYSTEM RELATED PARTS To replace immobilizer system related parts, refer to the table below. When the
ignition key is re-registered with scan tool MB991958, the originally registered
ignition key registration information will be lost.
Fig. 4: Identifying PCM Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
IGNITION KEY REMINDER TONE ALARM AND DOOR LOCK PREVENTION FUNCTION
DIAGNOSIS The Ignition key reminder tone alarms and door lock prevention function are
controlled by the Simplified Wiring System (SWS). For troubleshooting, refer to
SIMPLIFIED WIRING SYSTEM (SWS)
- ENDEAVOR
.
IMMOBILIZER SYSTEM DIAGNOSIS INTRODUCTION TO IMMOBILIZER SYSTEM DIAGNOSIS < UP TO DECEMBER 2003 > The immobilizer system consists of the immobilizer-ECU, PCM and ignition key. I
f
the engine cannot be sta
rted
by using a registe
red ignition k
ey,
one of these

CAUTION: The encrypted code should always be re-registered
when replacing the immobilizer-ECU.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 17: Identifying Connector C
-310

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are immobilizer-ECU connector C-39 and key reminder switch
connector C-310 in good condition?
YES: Go to Step 6.
NO: Repair or replace the damage component(s). Confirm that scan tool
MB991958 communicates normally.
STEP 6. Check the wiring harness between immobilizer-ECU connector
C-39 (terminal 7 and 8) and key reminder switch connector C-310
(terminal 7 and 3).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 19: Identifying Connector C310

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are the wiring harness between immobilizer-ECU connector C-39
(terminal 7 and 8) and key reminder switch connector C-312 (terminal 7
and 3) in good condition?
YES: Replace the immobilizer-ECU and then register the password
(secret code) and encrypted code (Refer to ON
-VEHICLE SERVICE
).
Retest the system.
NO: Repair or replace the damaged component(s). Confirm that scan tool
MB991958 communicates normally.
DTC 12: ENCRYPTED CODES ARE NOT THE SAME OR NOT REGISTERED DTC SET CONDITION The encr
ypted code sent b
y the trans
ponder is not the same encr
ypted code which is

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor