2004 MITSUBISHI ENDEAVOR solenoid

YES: Repair or replace the damaged component(s). Then go to Step 8 .
NO: An open or short circuit may be present in the solenoid valve power
supply circuit. Repair the wiring harness between ABS-ECU connector A-
02 terminal 1 and fusible link No.3. Then go to Step 8 .
STEP 5. Measure the resistance at ABS-ECU connector A-02.
1. Disconnect the connector A-02, and connect special tool ABS Check
Harness (MB991970) to the wiring harness-side connector.
2. Measure the resistance between terminal 2 and ground. It should be 2
ohms or less. NOTE: Do not connect special tool ABS Check Harness
(MB991970) to the ABS-ECU.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

2004 TRANSMISSION
Automatic Transaxle Overhaul - Endeavor
GENERAL INFORMATION This automatic transaxle is made up of the following main parts.
The gear train is made up of 3 multi-plate clutches, 2 multi-plate brakes and 2
planetary gears made up of a sun gear, carrier, pinion gear and annulus gear.
The torque converter employs a 3 element, 1 step, 2 phase lock-up clutch.
The cases consist of a converter housing, transaxle case, rear cover and a valve
body cover.
Parts related to oil pressure regulation are the oil pump, which pressurizes the oil;
the regulator, which controls the pressure setting; the solenoid valves, which
changes the oil pressure with electrical signals; the pressure control valve, which
controls the oil pressure coming from the solenoid valve that effects each clutch and
brake; each kind of valve, which carry out the retention of the oil pressure through
the lines; and finally the valve body, which houses all the valves. SECTIONAL VIEW < F4A5A >
2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor


2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor

Fig. 18: Identifying Manual Control Shaft Detent

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
12. Disconnect the solenoid valve harness from the valve by undoing the fluid
tem
perature sensor and all the connectors.

2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor

Fig. 19: Identifying Solenoid Valve Harness From Valve Body

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
13. Remove the valve bod
y mountin
g blots
(twent
y seven
places
).
CAUTION:
Make sure that the manual control lever and
the park/neutral position switch are removed.
See step 8. Do not remove the bolts (four pieces) shown
in the illustration.

2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor

Fig. 21: Removing Valve Body Gasket And Two Steel Balls

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
15. Remove the snap ring from the connector and then push the connector into the
transaxle case and remove the solenoid valve harness.

2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor

90. Install the strainer and second brake retainer oil seal.
Fig. 133: Installing Strainer And Second Brake Retainer Oil Seal

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
91. Insert a new O-ring to the groove of the solenoid valve harness connector.
92. Insert the solenoid valve harness connector into the hole from the inside of the
transaxle case so it is oriented as shown in the illustration. Then secure the
sna
p rin
g to the connector
groove.

2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor

Fig. 136: Installing Valve Body Mounting Bolts

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
96. Attach the solenoid valve harness to the valve body by connecting the fluid
tem
perature sensor and all the connectors.

2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor

Fig. 137: Attaching Solenoid Valve Harness To Valve Body

Courtes
y of MITSUBISHI MOTOR SALES OF AMERICA
.

2004 Mitsubishi Endeavor XLS
2004 TRANSMISSION Automatic Transaxle Overhaul - Endeavor