2004 KIA Amanti Owner's Manual

Knowing your vehicle14
3
1
2
3
4
5
6
7
8
9
➀ Driver’s door power window switch
➁ Front passenger’s door power win-
dow switch
➂ Rear door (left) power window
switch
➃ Rear door (right) power window
switch
➄ Window opening and closing
(see page 3-16)
\b Automatic power window
(see page 3-16)
➆ Power window lock switch
(see page 3-17)
 Automatic window reversal (see page 3-16)
 Power window timer (see page 3-17)
WINDOWS
2GHA2300
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 14

315
1
2
3
4
5
6
7
8
9
Knowing your vehicle
Power windows The ignition switch must be in the ON
position for power windows to oper-
ate. Each door has a power window
switch that controls that door’s win-
dow. However, the driver has a power
window lock switch which can block
the operation of passenger windows.
If you notice buffeting and pulsation
(wind shock) with either side window
open, you should open the opposite
window slightly to reduce the condi-
tion.
✽ ✽NOTICETo prevent the power window sys-
tem from the possibility of damage,
do not open or close two windows at
the same time. This will also ensure
the longevity of the fuse.
CAUTION
 Do not allow children to play
with the power windows. Keepthe driver’s door power win-dow lock switch in the LOCKposition (depressed). Seriousinjury can result from uninten-tional window operation bythe child.
 Do not extend face or arms outside through the windowopening while driving.
 Always double check to make sure all arms, hands and otherobstructions are safely out ofthe way before closing a win-dow
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 15

Knowing your vehicle16
3
1
2
3
4
5
6
7
8
9
Window opening and closingThe driver’s door has a master power
window switch that controls all the
windows in the vehicle. To open or
close a window, press down or pull
up the front portion of the correspon-
ding switch.
Automatic power windowDepressing or pulling up the power
window switch momentarily to the
second detent position (
\b) com-
pletely lowers or lifts the window
even when the switch is released. To
stop the window at the desired posi-
tion while the window is in operation,
pull up or depress the switch
momentarily to the opposite direction
of the window movement.
If the battery has been discharged
or disconnected, the automatic
power window system must be reset
as follows:
1. Turn the ignition key to ON posi- tion.
2. Close each window and continue pulling up on each power window
switch for at least 0.5 second after
the window is completely closed. Automatic window reversal (When
window is closed by the automatic
power window)
If the upward movement of the win-
dow is blocked by an object or part of
the body, the window will detect the
resistance and will stop upward
movement. The window will then
lower approximately 15cm to allow
the object to be cleared.
1GHA2301
1GHA2300B1GHA2300A
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 16

317
1
2
3
4
5
6
7
8
9
Knowing your vehicle
Power window lock switch The driver can disable the powerwindow switches on a passenger
door by depressing the power win-
dow lock switch located on the dri-
ver’s door to LOCK (pressed).
 When the power window lock switch is ON, the driver’s master
control cannot operate the passen-
ger door power windows either.
Power window timer
(if equipped)The power windows can be operated
for approximately 30 seconds after
the ignition key is removed or turn to
the ACC or LOCK position. However,
if the front doors are opened, the
power windows cannot be operated
even within the 30 seconds after the
ignition key removal.
WARNING
 The automatic window rever- sal feature (window lowers
150 mm when resistance is
detected) will only operate
when the automatic power
window up operation feature
is used. Automatic window
reverseal will not operate if
the window is raised using the
first detent position (
➄) on the
power window switch. Always
double check to make sure all
faces, arms, hands and other
obstructions are safely out of
the way of before operating
the power window.
 If an object less than 4 mm in diameter is caught between
the window glass and the
upper window channel, the
automatic reversal may not
detect the resistance and will
not operate. Therefore, always
check for any obstructions
before raising any window.
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 17

Knowing your vehicle18
3
1
2
3
4
5
6
7
8
9
Driver’s seat
➀
Seat adjustment, forward / back-
ward/height (see page 3- 20)
➁
Seatback recliner (see page 3- 22)
➂
Seat heater switch (see page 3- 22)
➃
Lumbar support (see page 3- 23)
➄
Driver position memory system
(see page 3- 24)


Headrest adjustment (headrest
can not be adjusted by a switch)(see page 3- 24)
Front passenger seat
\b
Seat adjustment, forward / back-
ward (see page 3- 25)
➆
Seatback recliner (see page 3- 26)
➇
Seat heater switch (see page 3- 27)


Headrest adjustment (headrest
can not be adjusted by a switch)(see page 3- 28)
Rear seat
\f
Seat heater switch (left) (see page 3- 31)
➉
Seat heater switch (right)(see page 3- 31)


Headrest adjustment (see page 3- 32)
SEAT
ESP
2GHN2025
No Function
No Function
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 18

319
1
2
3
4
5
6
7
8
9
Knowing your vehicle
WARNING
- Driver’s seat
 Never attempt to adjust seat
while the vehicle is moving.
This could result in loss of
control, and an accident caus-
ing death, serious injury, or
property damage.
 Do not allow anything to inter- fere with the normal position
of the seatback. Storing items
against a seatback or in any
other way interfering with
proper locking of a seatback
could result in serious or fatal
injury in a sudden stop or col-
lision.
(Continued)
For a seating position more comfort-
able to the driver and front passen-
ger, adjust the seat forward, back-
ward, up and down.✽ ✽NOTICE• Power seats are driven by the elec-
tric motor. Stop operating if the
adjustment is completed. Excessive
operation may damage the electri-
cal equipment.
• When in operation, the power seats consume large amounts of
electrical power. To prevent unnec-
essary charging system drain,
don’t adjust the power seats longer
than necessary while the engine is
not running.
• Do not operate two or more power seat control buttons at the same
time. Doing so may result in power
seat motor or electrical component
malfunction.
WARNING
 Loose objects in the driver ’s
foot area could interfere with
the operation of the foot ped-
als, possibly causing an acci-
dent. Loose objects might
interfere with the seat slide
mechanism. Do not place any-
thing under the front seats.
 The power seats are operable
with the ignition OFF.
Therefore, children should
never be left unattended in the
car.
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 19

Knowing your vehicle20
3
1
2
3
4
5
6
7
8
9
Driver’ s seat adjustmentForward/backward position and
height adjustmentAdjusting the seat forward and back-
ward
Push the control button forward or
backward to move the seat to the
desired position. Release the knob
and the seat will lock in the selected
position. Adjust the seat before driving, and
make sure the seat is locked secure-
ly by trying to move forward and
backward without using the control
knob. If the seat moves, it is not
locked properly.
(Continued)
 Always drive and ride with
your seatback upright and the
lap portion of the safety belt,
or lap belt, snug and low
across the hips. This position
puts your safety belts in the
best position to protect you in
case of an accident.
 In order to avoid unnecessary
airbag injuries including the
possibility of severe injury or
death, always sit as far back
as possible from the steering
wheel while still being able to
maintain comfortable control
of your vehicle.
 The Canadian Motor Vehicle
Safety Standards (CMVSS)
recommends that the driver
sit at least 10 inches (250 mm)
away from the steering wheel
to avoid the risk of serious
injury or death due to the
deployment of the driver’ s
airbag.
2GHA2238
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 20

321
1
2
3
4
5
6
7
8
9
Knowing your vehicle
Adjusting front height of seat cushion
Move the front portion of the control
knob up to raise or down to lower the
front part of the seat cushion.Adjusting rear height of seat cushion
Move the rear portion of the control
knob up to raise or down to lower the
rear part of the seat cushion.Adjusting the height of seat cushion
To raise or lower the seat cushion,
pull up or push down on the center of
the corresponding switch. Release
the knob once the seat reaches to
the desired position.
2GHA2239
2GHA2240
2GHA2241
Opirus-ENG (CAN) 3.qxd 7/8/03 1:56 PM Page 21