2004 ISUZU TF SERIES oil

4C1-18 FRONT WHEEL DRIVE
FRONT AXLE DRIVE SHAFT
Front Axle Drive Shaft and Associated Parts
RTW34CLF000401
Legend
1. Axle Case and Differential
2. Snap Ring
3. Bearing
4. Snap Ring
5. Oil Seal
6. Bracket
7. DOJ Case
8. Circlip
9. Bolt
10. Drive shaft Joint Assembly
11. Ball


12. Snap Ring
13. Ball Retainer
14. Ball Guide
15. Band
16. Bellows
17. Band
18. Band
19. Bellows
20. Band
21. UJ Shaft
22. Dust Seal

4C1-20 FRONT WHEEL DRIVE
6. Using snap ring pliers, remove the snap ring (1) fastening
the ball retainer to the center shaft.
7. Remove ball retainer, ball guide and bellows.



8. Use a hammer and chisel to remove the 3 pawls (above
the large and small boot bands on the UJ side).
CAUTION :
Take care not to damage the bellows during band removal.

9. Remove band (1).
10. Remove bellows.
11. Remove dust seal from UJ.
12. Remove UJ shaft assembly.
13. Remove the mounting bracket fixing bolts, and then
remove DOJ case assembly from the axle case.
14. Remove snap ring and bearing.
15. Remove snap ring and oil seal.
16. Remove bracket.


Inspection And Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are found
through inspection.
Check the following parts.
1. Drive shaft joint assembly
2. DOJ case, ball, ball guide, ball retainer
3. Bellows
4. Bearing
5. Dust seal, oil seal

FRONT WHEEL DRIVE 4C1-21

Bushing Replacement
 Remove the bushings using a remover 5-8840-2309-0 and
hammer.




By using installer and base 5-8840-2309-0, press fit the
bushings into the bracket.

Reassembly
1. Install DOJ case to bracket.
2. Install oil seal and fix snap ring.
Discard the used oil seal, snap ring and install a new one.
3. Install bearing and fix snap ring.
Discard the used snap ring and install a new one.
4. Install bracket to axle case. Tighten the bracket bolt to the
specified torque.
Torque : 116 N·m (11.8kg·m/85 lb ft)
5. Apply 135g of the specified grease in UJ.
6. Install dust seal for UJ.
Discard the used dust seal and install a new one.

Legend
1. Bellows
2. Shaft
7.
Apply a thin coat of grease to the shaft for smooth
installation then install bellows.
CAUTION :
During bellows assembly, be sure to insert both ends of
the bellows into the case and shaft grooves.

4C1-24 FRONT WHEEL DRIVE
DIFFERENTIAL
DISASSEMBLY
MAJOR COMPONENTS
RTW34CLF000501
Disassembly Steps
1. Bolt
2. Differential assembly
3. Axle case
4. Bolt


5. Bearing cap
6. Diff. cage assembly


7. Side bearing outer race


8. Side bearing


9. Adjust shims


10. Flange nut
11. Flange


12. Dust cover


13. Pinion gear


14. Inner bearing
15. Adjust shim
16. Collapsible spacer


17. Inner bearing outer race
18. Oil seal
19. Outer bearing


20. Outer bearing outer race
21. Diff. carrier

FRONT WHEEL DRIVE 4C1-29
INSPECTION AND REPAIR
Make all necessary adjustments, repairs, and part replacements if wear, damage, or other problems are discovered
during inspection.



Ring gear, pinion gear

Bearing


Side gear, pinion gear, cross pin


Differential cage, carrier


Thrust washer


Oil seal


Visual Check
Inspect the following parts for wear, damage, or other
abnormal conditions.



Ring Gear Replacement
(1) The ring gear should always be replaced with the drive
pinion as a set.
(2) When installing the ring gear, apply LOCTITE 271 o
r
equivalent to the threaded hole and bolt.
(3) Tighten the fixing bolts in a diagonal sequence as
illustrated.
(4) Discard used bolts and install new ones.
Bolt Torque N
m (kgf
m/lb
ft)

107.9
9.8 (11
1/79.6
7.2)




Clearance Between the Differential Pinion
and the Cross Pin
mm(in)

Standard Limit
0.05 - 0.10 (0.002 - 0.004) 0.2 (0.008)



Clearance Between the Side Gear and the
Differential Box
mm(in)

Standard Limit
0.03 - 0.10 (0.001 - 0.004) 0.15 (0.006)

FRONT WHEEL DRIVE 4C1-33
MAJOR COMPONENTS


Reassembly Steps
1. Diff. carrier


2. Outer bearing outer race


3. Inner bearing outer race


4. Adjust shim


5. Inner bearing


6. Collapsible spacer
7. Pinion gear
8. Outer bearing


9. Oil seal
10. Dust cover


11. Flange


12. Flange nut and washer


13. Adjust shim


14. Side bearing
15. Bearing outer race
16. Diff. cage assembly


17. Bearing cap


18. Bolt
19. Axle case


20. Differential assembly
21. Bolt

4C1-34 FRONT WHEEL DRIVE




Important Operations
2. Outer Bearing Outer Race
Installer : 9-8522-1141-0
(J-24256)
Grip : 5-8840-0007-0
(J-8092)


3. Inner Bearing Outer Race
Installer : 9-8522-1274-0
Grip : 5-8840-0007-0
(J-8092)







4. Adjust Shim
Adjustment of drive pinion mounting distance
(1) Apply gear oil to the inner and outer drive pinion bearing.
Clean the pinion setting gage set.
Then install the gage set together with the inner and oute
r
bearings.

1. Pilot : 5-8840-2085-0
(J-21777-42)
2. Nut and bolt : 5-8840-2089-0
(J-23597-9)
3. Gage plate : 5-8840-2087-0
(J-23597-7)

FRONT WHEEL DRIVE 4C1-37
(7) Select the shim using the chart;

mm(i n)
Pi ni on
marki ng

+10 +8 +6 +4 +2 0 -2 -4 -6 -8 -10 Dial indicator
reading (inches)
0.081 2.18 (0.0858)0.082 2.18 (0.0858) 2.20 (0.0866)0.083 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882)0.084 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890)0.085 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898)0.086 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914)0.087 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921)0.088 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929)0.089 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937)0.090 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937)2.42 (0.0953)0.091 2.18 (0.0858) 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961)0.092 2.20 (0.0866) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969)0.093 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977)0.094 2.26 (0.0890) 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992)0.095 2.28 (0.0898) 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000)0.096 2.32 (0.0914) 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008)0.097 2.34 (0.0921) 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0.098 2.36 (0.0929) 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0.099 2.38 (0.0937) 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0 2.42 (0.0953) 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0.001 2.44 (0.0961) 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0.002 2.46 (0.0969) 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0.003 2.48 (0.0977) 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0.004 2.52 (0.0992) 2.54 (0.1000) 2.56 (0.1008) 0.005 2.54 (0.1000) 2.56 (0.1008) 0.006 2.56 (0.1008)
Note :
When ordering shims, find the part number in the Parts Catalog by using the thickness of the shims listed
in the above table.







5. Inner Bearing
Place the shim on the drive pinion, with the chamfered side
turned towards the pinion head then install the inner bearing on
to the pinion using an installer and a press.
Installer : 9-8522-1165-0 (J-6133-01)
Note:
Do not apply pressure to the roller cage.
Apply pressure only to the inner race.



6. Collapsible Spacer
Discard the used collapsible spacer and install a new one.







9. Oil Seal
Use oil seal installer to install a new oil seal that has been
soaked in rear axle lubricant.
Installer : 9-8522-1275-0 (J-24250)
Note :
Take care not to use a rear differential oil seal instead of
the front differential oil seal.