2004 ISUZU TF SERIES lock

7A2-10 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

Control and Functions
Shift Control
The transmission gear is shifted according to the shift
pattern selected by the driver. In shifting gears, the
gear ratio is controlled by the ON/ OFF signal using the
shift solenoid S1 and the shift solenoid S2.
Band Apply Control
The band apply is controlled when in the 3 –2 downshift
(engine overrun prevention) and the garage shift (shock
control).
The band apply solenoid is controlled by the signal from
the Pulse Width Modulation (PWM) to regulate the flow
of the oil.
Torque Converter Clutch Control
The clutch ON/OFF is controlled by moving the
converter clutch valve through shifting Torque
Converter Clutch (TCC) solenoid using the ON/OFF
signal.
Line Pressure Control
The throttle signal allows the current signal to be sent
to the force motor. After receiving the current signal,
the force motor activates the pressure regulator valve
to regulate the line pressure.
On –Board Diagnostic System
Several malfunction displays can be stored in the
Transmission Control Module (TCM) memory, and read
out of it afterward.
The serial data lines, which are required for the testing
of the final assembly and the coupling to othe
r
electronic modules, can be regulated by this function.
Fail –Safe Mechanism
If there is a problem in the transmission system, the
TCM will go into a “backup" mode.
The vehicle can still be driven, but the driver must use
the select lever to shift gears.
Torque Management Control
The transmission control side sends the absolute spark
advance signal to the engine control side while the
transmission is being shifted. This controls the engine
spark timing in compliance with the vehicle running
condition to reduce the shocks caused by the change o
f
speed.
ATF Warning Control
The oil temperature sensor detects the ATF oil
temperature to control the oil temperature warning,
TCC, and the 3rd start mode.
Reverse Lock Out Control
With the selector lever in reverse position, the TCM will
not close the PWM solenoid until the vehicle is below
15 km/h (9.3 mph), thus preventing reverse
engagement above this speed.

Downhill Control
This mode is automatically activated from NORMAL
mode only when downhill conditions are recognized.
The shift pattern is identical to NORMAL mode except
3-4 and 4-3 shift lines at low throttle modified to get
engine braking on a larger speed range.
Uphill Control
When uphill condition are recognized the 2-3 and 3-4
shift and TCC apply are down only when the engine
torque is sufficient in order to avoid shift hunting.
Gear Shift Control 3rd start


SELECT LEVER RANGE SHIFT PATTERN
D(Drive) 1


2TCC

3TCC

4TCC
3(Third) 1

2TCC

3TCC
2(Second) 1

2(
3)
L(First) 1(
2)
TCC: Torque Converter Clutch
(Notice1): “( )" means over-revving prevention control.
Mode Type


Mode Type Select lever position
Normal drive mode
(NOR) Entire range (excluding “R")
Power drive mode
(PWR) Entire range (excluding “R")

Mode Selection



SWITCH(SW) LAMP
Mode Type PWR/N
OR.S 3RD
START SW POWER
DRIVE LAMP 3RD
START LAMP
Normal
drive mode
(NOR) OFF OFF OFF OFF
Power
drive mod
(PWR) ON OFF ON OFF
3rd Start
mode OFF ON OFF ON
However, the 3rd start switch prevails over the
PWR/NOR switch.
The mode become normal drive mode when the 3rd
start switch is operated from ON to OFF.

7A2-12 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

Functions of Input / Output Components
Component Function
Transfer low signal Detects the transfer High/Low position.
OD Cancel signal Detects whether the cruise control unit is judged OD cancel mode.
Output revolution sensor
(Transmission) Detects the vehicle speed.
Input revolution sensor
(Transmission) Detects the input revolution (OD direct clutch drum revolution).
Engine revolution sensor Detects the engine revolution with CAN.
Throttle position signal Detects the throttle opening rate with CAN.
Neutral start switch Detects the select lever position.
Pattern select switch Detects whether the driver has selected "NORMAL" or "POWER" mode.
Brake lamp switch Detects whether the driver has pressed the brake pedal or not.
Oil temperature sensor Detects the oil temperature.




I
n
p
u t
Diagnostic start switch Starts self-diagnosis and displays a code for faulty part if any.
I
n
p
u t
/
O
u t
p
u t Data link connector When connected with Tech2 or tester, can communicate the data for function
check, etc.
Shift solenoid S1, S2 Selects shift point and gear position suited to the vehicle running condition on the
basis of TCM output.
Lock-up control solenoid SL Control the lock-up clutch suited to the vehicle running condition on the basis of TCM output.
Pressure control solenoid
STH Adjusts throttle pressure by energizing current of linear pressure control solenoid
to prevent the shift shock and to obtain shift smoothly.
"CHECK TRANS" lamp When trouble has occurred to throttle position sensor, vehicle speed sensor, or
solenoid, "CHECK TRANS" lamp is blinked to warn the driver. If also displays the
trouble code.
A/T OIL TEMP warning
lamp Lights when ATF oil temperature rises. (Turned on at greater than 146


C
(295

F). Turned off at less than 132

C (270

F).
POWER lamp Lights when POWER MODE detected.



O
u
t
p
u
t
3rd Start lamp Lights when 3rd Start MODE detected.
C
o
m
p
u t
e r Transmission Control
Module (TCM) Based on the signal from each switch and sensors, judges necessary shift point
and lock-up operation, and send signal to each solenoid.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-37

DTC P0602 (FLASHING CODE 63) Transmission Control Module (TCM)
Programming Error
Circuit Description
The Service Programming System (SPS) updates the
flash calibration files that are stored in a Transmission
Control Module (TCM). The calibration file
custom-tailors a module to a certain vehicle. The
calibration file contains data for things such as spark
curves and fuel control. When troubleshooting a
driveability problem, diagnosis may call fo
r
reprogramming the controller with newer calibration
information to correct a customer concern and Vehicle
Identification Number (VIN).
Condition for setting the DTC
When the TCM is not written VIN No.
Action Taken When The DTC Sets

DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids
DTC P0602 is indicated when the TCM does not written
VIN No. A security lock is performed by SPS. And not
replace the TCM when DTC P0602 can repair by SPS.

7A2-38 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC P0602 (FLASHING CODE 63) Transmission Control Module (TCM)
Programming Error


Step Action Value(s) YES NO
1
Was the “On-Board Diagnostic (OBD) System Check"
performed? — Go to Step 2 Go to OBD
System Check
2

1. Install the scan tool.

2. Key “ON".
3. Check the Vehicle Identification Number (VIN) by
the scan tool.
Is VIN on the scan tool same as VIN of vehicles? — Go to Step 4 Go to Step 3
3 Write a VIN by the scan tool. (Refer to SPS for
procedure.)
Is the action complete? — Go to Step 4 —
4 Clear the DTC P0602 by the scan tool.
Is the action complete? — Go to Step 5 —
5 Perform the SPS and perform security lock. (Refer to
SPS for procedure)
Is the action complete? — Go to Step 6 —
6 Recheck the DTC by the scan tool.

1. Key “OFF".
2. Wait a few seconds.

3. Key “ON".

4. Review and record scan tool data.
5. Operate the vehicle with in scan tool data.
Is the action complete? — Go to Step 7 Verify repair
7 Replace the TCM.
Important:
The replacement TCM must be
programmed. (Refer to SPS for procedure.)
Is the action complete? — Verify repair —

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-49

DTC P0717 (FLASHING CODE 14) Input Speed Sensor Signal Error

MAW060MF001501

Circuit Description
Input revolution information is provided to TCM by the
input revolution sensor. This sensor is located in the
transmission case.
The input revolution sensor is an electromagnetic pulse
pickup type that generates a speed signal according to
the revolution of the transmission OD direct clutch
drum. As a result, the sensor sends a sine wave signal
(AC) to the TCM, which converts this sine wave signal
(pulse voltage) to a RPM signal.
Condition for setting the DTC
The TCM detects following conditions at 1000
times continuously.

When the TCM detects following conditions at the
same time.
 When output speed is over 775 rpm (16 mph) at
gear position is 1st or 2nd or 3rd.

Input speed signal is no pulse while output speed
signal are 12 pulses.

OR

When the TCM output 2nd gear.
 The TCM detects no pulse of input speed senso
r
circuit signal after 3.5 sec.
(detection time: 0.03 sec at vehicle speed is 36 mph)
Action Taken When The DTC Sets

No engine torque control.
 No line pressure control.

No lock-up control.

No slope control.

Check Trans ON.
 DTC stored.

No detect DTC P0722.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

7A2-52 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC P0722 (FLASHING CODE 11) Output Speed Sensor Signal Error


RTW37AMF000501

Circuit Description
Vehicle speed information is provided to the TCM by
the output revolution sensor. This sensor is located in
the transmission adapter housing.
The output revolution sensor is an electromagnetic
pulse pickup type that generates a speed signal
according to the revolution of the transmission output
shaft. As a result, the sensor sends a sine wave signal
(AC) to the TCM, which converts this sine wave signal
(pulse voltage) to a RPM signal.
Condition for setting the DTC
The TCM detects following conditions at 500 times
continuously.
(When gear positions are 1st, 2nd and 3rd.)
When the TCM detects following conditions at the
same time.

Output speed signal is no pulse while input speed
signal are 45 pulses.
(Detection time, 1st: 0.031 sec, 2nd: 0.057 sec, 3rd:
0.087 sec, at vehicle speed is 38 mph.)
Action Taken When The DTC Sets

The TCM uses input speed sensor as a vehicle
speed.

No squat control.

No engine torque control.
 No line pressure control.

No use 4th gear.

No lock-up control.
 No slope control.

Check Trans ON.

DTC stored.
 No reverse lockout control.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-55

DTC P0743 (FLASHING CODE 33) Torque Converter Clutch Electrical


RUW37ALF000601
Circuit Description
The lock-up solenoid SL of the torque converter clutch
(TCC) controls the lock-up clutch by a signal according
to the lock-up range judgment of the TCM when the
vehicle runs.
This function can improve the fuel consumption to
almost the same extent as the manual transmission.
The lock-up solenoid SL is put into B+ by the TCM, so
that the solenoid is actuated with the result of lock-up.
Condition for setting the DTC
The TCM detects following conditions both "Condition
1" and "Condition 2" occur 2 times or more than it.
Condition 1 ("GND short"):

Voltage at connector pin is 0V for 0.3 sec
continuously when solenoid is “ON".
Condition 2 ("Open or IG short"):

Voltage at connector pin is ignition voltage for 0.5
sec continuously when solenoid is “OFF".
Action Taken When The DTC Sets

No lock-up control.
 The TCM fixes to 1st gear when the vehicle speed is
less than 6 mph.

Check Trans ON.

DTC stored.

7A2-58 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC P0748 (FLASHING CODE 35) Pressure Control Solenoid Electrical



RTW37ALF000601
Circuit Description
The pressure control solenoid is a PWM duty control
solenoid located in the valve body.
The pressure control solenoid is a TCM-controled
device used to regulate transmission throttle pressure
by energizing current from the TCM.
Condition for setting the DTC
The TCM detects following "Condition 1" and "Condition
2".
Condition 1("Ignition short"):

When the TCM detects following condition for 0.5
sec continuously.

Monitor A/D value is more than 1000 (1.36A).
Condition 2("Open or GND short"):

When the TCM detects following condition for 70
msec continuously.

Monitor A/D value is less than 15 (20mA).
Action Taken When The DTC Sets

No squat control.
 No line pressure control.

No lock-up control.

No slope control.
 Check Trans ON.