2004 ISUZU TF SERIES reverse switch

DIAGNOSIS (JR405E) 7A2-101
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4

If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Terminal
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressu re SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VGo to Step 6
Repair the defect or
replace.

7A2-106 DIAGNOSIS (JR405E)
No. B6: Engine Starter Does Not Run in P or N Range
No. B7: Engine Starter Runs Except in P or N Range

Description:

The engine starter does not run though the P or N range is selected.

The engine starter runs though the R or D, 3, 2or L range is selected.

Possible Cause:

Disordered select cable.

Disordered Inhibitor switch, disconnection or short-circuit of inhibitor switch.


No. B8: Extended Time Lag When Shift Lever is Changed to N to D

Description:

The shift time lag is longer than standard value when shift lever is changed to N to D.

Possible Cause:

Forward range line pressure is low.

Slip of low & reverse clutch.

Slip of low one-way clutch.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Faulty low clutch duty solenoid operation.

Shortage or faulty quality of ATF.


No. B9: Extended Time Lag When Shift Lever is Changed to N to R

Description:

The shift time lag is longer than standard value when shift lever is changed to N to R.

Possible Cause:

Reverse range line pressure is low.

Slip of low & reverse brake.

Slip of reverse clutch.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Faulty low & reverse brake duty solenoid operation.

Shortage or faulty quality of ATF.

DIAGNOSIS (JR405E) 7A2-109
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Terminal
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressu re SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10V
Go to Step 6
Repair the defect or
replace.

7A2-112 DIAGNOSIS (JR405E)
Step Action Yes No
1
Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Te r m i n a l
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressure SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VGo to Step 6
Repair the defect or
replace.

DIAGNOSIS (JR405E) 7A2-117
Step Action Yes No
5 Inspection of electrical or mechanical fault
Is signal to each solenoid and pressure switch changed
synchronously to the faulty gear shift?

Control Valve


TCM


B1





B12





B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW

Terminal
Assembly
YEL
E54

(7)





(12)





(1) H23

(12)





(10)C95

(1)





(12)





(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW

High Clutch Pressure SW

H22

(8)
Control Valve

TCM
B6
B7
B8
B9
B22 (GND) BLU/BLK
WHT/BLU L&R Brake Solen oid

Te r m i n a l
Assembly
BLK/YEL
RED
2-4 Brake Solenoid

High Clutch Solenoid

Low Clu tch S olen oid

E54
(5)
(9)
(10)
(3)
(11)H23
(11)
(5)
(7)
(2)
(1)
GRY/REDC95
(6)
(7)
(8)
(9)
(22) BLU/BLK
BLK/YEL
RED
WHT/BLU
GRY/RED
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressure SW)P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10V
Range TCM terminal
GearB8
(High clutch
solenoid)B9
(Low clutch
solenoid)B7
(2 -4 b rake
solenoid)B6
(Lo w & reve rs e
brake solenoid)P - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.2V
(AC ra ng e)
R Reverse Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)-
N - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
D, 3, 2 1st Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
2nd Approx. 6.8V
(AC range)- - Approx. 6.8V
(AC ra ng e)
3rd - - Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
4th - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC ra ng e)
L 1st Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)-
2nd Approx. 6.8V
(AC range)- - Approx. 6.8V
(AC ra ng e)
3rd - - Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
4th - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC ra ng e)
Go to Step 6
In case of fault in
the machine
system, repair that
portion or replace
the unit.
Slip of clutch or fault
of control valve.

DIAGNOSIS (JR405E) 7A2-139
No. Z11: Abnormal Oil Pressure

Description:

Oil pressure is low or high.

Possible Cause:

Basically, the same cause as "No. C1 - C8: Engine races up (slip) by shift up or shift down" is considered.

In case of oil pressure is low, faulty oil pump is considered.




No. Z12: Reverse Buzzer Does Not Ring

Description:

Reverse buzzer does not ring in R range.

Possible Cause:

Disordered select cable.

Disordered select lever.

Disordered inhibitor switch.

7A2-140 DIAGNOSIS (JR405E)
STALL TEST
CAUTION:
Because A/T may break down, do not perform the stall test continuously.

Procedure
1. Chock the four wheels.
2. Warm up the engine.
3. Apply the parking brake.
4. Step on the foot brake fully.
5. Set the select lever to either D, 3, 2, L or R range.
6. Step on the accelerator pedal fully.
7. When the engine speed becomes constant, record tha
t
value quickly.

Stall Speed
Standard: 2600±150 rpm

Evaluation
1. If the stall speed is higher than standard value in all
ranges.

Low line pressure.

Abraded oil pump.

Faulty operation of low clutch.

Adjustment error of or faulty inhibitor switch.


ATF leaking from oil pump, control valve, or
transmission case.

Fixed pressure regulator valve and pilot valve.
2. If the stall speed is higher than standard value in D, 3, 2
and L ranges.

Slip of low clutch.

Slip of low one-way clutch.
3. If the stall speed is higher than standard value in
R
range.

Slip of low & reverse brake.

Slip of reverse clutch.
4. If the stall speed is lower than standard value in all
ranges.

Slip of one-way clutch (in torque converter).

Faulty engine.

7A2-156 DIAGNOSIS (JR405E)
No. Wire
Color Pin Name Input /
OutputConnected toMeasurement
Item Measurement
Condition StandardInspection
Point at
Trouble
At lamp OFF 10 – 14.5V Related
harness A24 GRN/
YEL Power Drive Select Switch InputPower drive
switch Voltage
At lamp ON Less than 2V Lamp
At other than
2nd or 4th
gear More than 10
V Related
harness
B1 RED/
YEL 2-4 Brake Pressure Switch Input2-4 brake
pressure switch Voltage
At 2nd or 4th
gear Less than 2VPressure
switch
At 2 range 10 – 14.5V Related
harness
B2 PNK/
BLK 2 Range Switch Input Inhibitor switch Voltage
At other than
2 range Less than 2VInhibitor
switch
InputRelated
harness
B3 BRN/
RED Turbine Sensor

Turbine sensor Voltage (Wave
form) At run in L
range in 1st
gear 20 km/h.
Circuit tester
(+) to B3 pin,
(-) to B5 pin. Pulse
generated (At
AC range
approx. 6.5V)Turbine
sensor
ATF temp.
20
C Approx. 1.55
V Related
harness
B4 BLU ATF Thermo Sensor InputATF thermo
sensor Voltage
ATF temp.
60
C Approx. 0.7VThermo
sensor
B5 BLK Ground - Ground Voltage Normally Less than 2VRelated
harness
Related
harness
B6 BLU/
BLK Low & Reverse Brake Duty Solenoid OutputLow & reverse
brake duty
solenoid Voltage (Wave
form) P, N range.
Circuit tester
(+) to B6 pin,
(-) to B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
Related
harness
B7 BLK/
YEL 2-4 Brake Duty Solenoid Output2-4 brake duty
solenoid Voltage (Wave
form) P, N range.
Circuit tester
(+) to B7 pin,
(-) to B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
Related
harness
B8 RED High Clutch Duty Solenoid OutputHigh clutch duty
solenoid Voltage (Wave
form) P, N range.
Circuit tester
(+) to B8 pin,
(-) to B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
Related
harness
B9 WHT/
RED Low Clutch Duty Solenoid OutputLow clutch duty
solenoid Voltage (Wave
form) 4th gear in D
range. Circuit
tester (+) to
B9 pin, (-) to
B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
At N range 10 – 14.5V Related
harness
B10 RED/
BLK N Range Switch Input Inhibitor switch Voltage
At other than
N range Less than 2VInhibitor
switch
At D range 10 – 14.5V Related
harness
B11 BLU D Range Switch Input Inhibitor switch Voltage
At other than
D range Less than 2VInhibitor
switch