2004 ISUZU TF SERIES fuel pump

4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS 6E–115
34 P0105 7 ON Vacuum Pressure Sensor
Voltage Supply Circuit High
InputVacuum sensor power
supply voltage is more than
5.2V.1. Fuel injection quantity is
r e d u c e d .
2. ECM use vacuum sensor
output voltage 5.0V
condition as substitute.Vacuum sensor power
supply voltage is below 5.2V.1. Sensor power supply
circuit short to battery
voltage circuit.
2. Vacuum sensor
m a l f u n c t i o n .
3. ECM malfunction.82 — —
9 ON Vacuum Pressure Sensor
Voltage Supply Circuit Low
InputVacuum sensor power
supply voltage is below 4.5V.Vacuum sensor power
supply voltage is more than
4.5V.1. Sensor power supply
circuit short to ground
c i r c u i t .
2. Vacuum sensor
m a l f u n c t i o n .
3. ECM malfunction.82 — —
23 P0110 1 ON Intake Air Temperature (IAT)
Sensor Circuit High InputIAT sensor output voltage is
more than 4.7V.ECM use 0 deg. C conditions
as substitute.IAT sensor output voltage is
below 4.7V.1. Sensor signal circuit
open or short to voltage
c i r c u i t .
2. Sensor ground circuit
open or short to voltage
c i r c u i t .
3. Poor connector
c o n n e c t i o n
4. IAT sensor malfunction.
5. ECM malfunction.8 4 /
92P0100(B)/







P0100(C)
2 ON Intake Air Temperature (IAT)
Sensor Circuit Low InputIAT sensor output voltage is
below 0.3V.IAT sensor output voltage is
more than 0.3V.1. Sensor signal circuit
short to ground circuit.
2. IAT sensor malfunction.
3. ECM malfunction.84 —
14 P0115 1 ON Engine Coolant Temperature
(ECT) Sensor Circuit High
InputECT sensor output voltage is
more than 4.7V.1. ECM uses fuel
temperature as
s u b s t i t u t e .
2. ECM uses 60 deg. C
condition for injection
t i m i n g c o n t r o l .
3. ECM uses -25 deg. C
condition (4JA1-TC) or -
15 deg. C condition
(4JH1-TC) for glow time
control.ECT sensor output voltage is
below 4.7V.1. Sensor signal circuit
open or short to voltage
c i r c u i t .
2. Sensor ground circuit
open or short to voltage
c i r c u i t .
3. Poor connector
c o n n e c t i o n
4. ECT sensor malfunction.
5. ECM malfunction.8 9 /
93P0105(1)
2 ON Engine Coolant Temperature
(ECT) Sensor Circuit Low
InputECT sensor output voltage is
below 0.3V.ECT sensor output voltage is
more than 0.3V.1. Sensor signal circuit
short to ground circuit.
2. ECT sensor malfunction.
3. ECM malfunction.89 —
15 P0180 B ON Fuel Temperature Sensor
Circuit Range/PerformanceFT sensor output is high
temperature (more than 150
deg. C) or low temperature
(below -40 deg. C).The ECM use 75 deg. C
conditions as substitute.FT sensor output is correct
temperature range between
150 deg. C and -40 deg. C.1 . E C M m a l f u n c t i o n .
2. PSG (pump control unit)
malfunction.—— Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)

6E–116 4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS
52 P0215 A ON Fuel Cutoff Solenoid Valve
Malfunction1. Ignition key switch off.
2. Engine speed is below
1 5 0 0 r p m .
3. Vehicle speed is below
1 . 5 k m / h .
4. PSG (pump control unit)
recognizes MAB (fuel
cutoff solenoid valve)
signal from the ECM, but
the MAB could not
operate. 1. MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d .
2. Desired injection quantity
becomes 0mg/strk.No recovery until condition
match in the next ignition key
cycle.1. PSG (pump control unit)
m a l f u n c t i o n .
2. MAB (fuel cutoff solenoid
valve) malfunction.
——
B ON Fuel Cutoff Solenoid Valve
Circuit High InputECM does not command
MAB (fuel cutoff solenoid
valve) signal to the PSG
(pump control unit), but PSG
detected MAB signal line
circuit is high level.Engine does not start. No recovery. 1. MAB (fuel cutoff solenoid
valve) signal circuit short
t o v o l t a g e c i r c u i t .
2. PSG (pump control unit)
malfunction.105 —
C ON Fuel Cutoff Solenoid Valve
Always Active1. Ignition key switch off.
2. Engine speed is below
1 5 0 0 r p m .
3. Vehicle speed is below
1 . 5 k m / h .
4. PSG (pump control unit)
does not recognize MAB
(fuel cutoff solenoid
valve) signal from the
ECM. 1. MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d .
2. Desired injection quantity
becomes 0mg/strk.No recovery until condition
match in the next ignition key
cycle.1. MAB (fuel cutoff solenoid
valve) signal circuit open
or short to ground circuit.
2. PSG (pump control unit)
malfunction.
105 —
D ON Fuel Cutoff Solenoid Valve
Malfunction1. Ignition key switch off.
2. CAN controller does not
operate Bus-off.N o f a i l - s a f e f u n c t i o n . 1 . E C M m a l f u n c t i o n .
2. PSG (pump control unit)
malfunction.——
54 P0216 A ON Injection Timing Control
Circuit Malfunction1. Engine speed is more
t h a n 7 0 0 r p m .
2. Fuel injection quantity is
more than 4mg/stk.
3. Deviation of actual
injection timing and
desired injection timing is
more than +3 deg. CA or
-6 deg. CA for 8 seconds.Fuel injection quantity is
reduced.Deviation of actual injection
timing and desired injection
timing is more than +3 deg.
CA or -6 deg. CA for 8
seconds.1. Timing control valve
m a l f u n c t i o n .
2 . T i m e r p i s t o n s t i c k i n g .
3. Pump camshaft speed
sensor malfunction.——
B ON Injection Timing Control
Circuit Malfunction 1. Engine speed is more
t h a n 2 0 1 4 r p m .
2. Fluctuation of actual
injection timing is more
than +-5.2 deg. CA.1. Engine speed is more
than 2014rpm.
2. Fluctuation of actual
injection timing is more
than +-5.2 deg. CA.1. Insufficient air bleeding of
f u e l l i n e .
2. Fuel filter clogging.
3. Timing control valve
m a l f u n c t i o n .
4. Pump camshaft speed
sensor malfunction. —— Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)

4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS 6E–117
64 P0243 3 ON Turbocharger Wastegate
Solenoid "A" Range/
Performance1. Intake air temperature is
between -50 deg. C and
2 0 0 d e g . C .
2. Engine coolant
temperature is between -
50 deg. C and 150 deg.
C .
3. Barometric pressure is
between 0hpa and
3 5 0 0 h p a .
4. Low vacuum pressure
condition. (Desired
vacuum pressure - actual
vacuum pressure is more
than 50hpa.)1. Fuel injection quantity is
r e d u c e d .
2. EGR EVRV becomes
1 0 % c o n d i t i o n . 1. Engine speed is between
500rpm and 6000rpm.
2. Correct vacuum pressure
condition. (Desired
vacuum pressure - actual
vacuum pressure is less
than 50hpa.)1. Turbocharger wastegate
control EVRV
m a l f u n c t i o n .
2. Vacuum line is
o b s t r u c t e d .
3. Vacuum is leaking.
4. Vacuum pump
m a l f u n c t i o n .
5. Vacuum sensor
m a l f u n c t i o n .
6. Turbocahrger wastegate
v a l v e m a l f u n c t i o n .
7. ECM malfunction.8 5 /
96——
4 ON Turbocharger Wastegate
Solenoid "A" Low Wastegate control EVRV
circuit open or short to
ground circuit.1. Fuel injection quantity is
r e d u c e d .
2. EGR EVRV becomes
1 0 % c o n d i t i o n .
3. Wastegate control EVRV
becomes 32% condition.Wastegate control EVRV
circuit is correct condition.1. Wastegate control EVRV
circuit open or short to
g r o u n d c i r c u i t .
2. Wastegate control EVRV
m a l f u n c t i o n .
3. ECM malfunction.96 — —
5 ON Turbocharger Wastegate
Solenoid "A" Range/
Performance1. Intake air temperature is
between -50 deg. C and
2 0 0 d e g . C .
2. Engine coolant
temperature is between -
50 deg. C and 150 deg.
C .
3. Barometric pressure is
between 0hpa and
3 5 0 0 h p a .
4. High vacuum pressure
condition. (Desired
vacuum pressure - actual
vacuum pressure is less
than -50hpa.)1. Fuel injection quantity is
r e d u c e d .
2. EGR EVRV becomes
1 0 % c o n d i t i o n . 1. Engine speed is between
500rpm and 6000rpm.
2. Correct vacuum pressure
condition. (Desired
vacuum pressure - actual
vacuum pressure is more
than -50hpa.)1. Turbocharger wastegate
control EVRV
m a l f u n c t i o n .
2. Vacuum regulating valve
m a l f u n c t i o n .
3. Vacuum pump
m a l f u n c t i o n .
4. Vacuum sensor
m a l f u n c t i o n .
5. ECM malfunction.8 5 /
96——
6 ON Turbocharger Wastegate
Solenoid "A" Malfunction1. Engine coolant
temperature is between -
50 deg. C and 150 deg.
C .
2. EGR control EVRV 0%
c o n d i t i o n .
3. No DTC relating to MAF
sensor, vacuum sensor &
I A T s e n s o r .
4. Large amount of mass air
flow. (= Incorrect boost
pressure condition)
(Desired mass air flow -
actual mass air flow is
less than -56mg/strk.)1. Correct amount of mass
air flow. (= Correct boost
pressure condition)
(Desired mass air flow -
actual mass air flow is
more than -56mg/strk.)1. Turbocharger wastegate
a c t u a t o r m a l f u n c t i o n .
2. Vacuum line malfunction.

































3. ECM malfunction.
——— Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)

6E–118 4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS
64 P0243 8 ON Turbocharger Wastegate
Solenoid "A" HighWastegate control EVRV
circuit short to voltage circuit.1. Fuel injection quantity is
r e d u c e d .
2. EGR EVRV becomes
1 0 % c o n d i t i o n .
3. Wastegate control EVRV
becomes 32% condition.Wastegate control EVRV
circuit is correct condition.1. Wastegate control EVRV
circuit short to voltage
c i r c u i t .
2. Wastegate control EVRV
m a l f u n c t i o n .
3. ECM malfunction.96 — —
53 P0251 6 ON Injection Pump Malfunction 1. No pump camshaft
s p e e d s e n s o r e r r o r .
2. High pressure solenoid
valve control pulse width
does not match with
desired fuel injection
quantity. 1. MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d .
2. Desired injection quantity
becomes 0mg/strk.No recovery until condition
match in the next ignition key
cycle.1. PSG (pump control unit)
m a l f u n c t i o n .
2. Pump camshaft speed
sensor malfunction.——
7 ON Injection Pump Malfunction 1. No pump camshaft
s p e e d s e n s o r e r r o r .
2 . N o C K P s e n s o r e r r o r .
3. Difference of engine
speed and doubled pump
camshaft speed is more
than 720rpm (4JA1-TC)
or 690rpm (4JH1-TC). 1. No pump camshaft
s p e e d s e n s o r e r r o r .
2 . N o C K P s e n s o r e r r o r .
3. Difference of engine
speed and doubled pump
camshaft speed is below
800rpm (4JA1-TC) or
6 9 0 r p m ( 4 J H 1 - T C ) .
No recovery until in the
next ignition key cycle. 1. Missing CKP sensor
p u l s e s .
2. Electrical interference.
3. Magnetic interference.
4. PSG (pump control unit)
malfunction.91 —
9 ON Injection Pump Malfunction No pump map programmed
in the PSG (pump control
unit) or PSG malfunction.No recovery until condition
match in the next ignition key
cycle.PSG (pump control unit)
malfunction. — —
A ON Injection Pump Malfunction EEPROM or A/D converter
malfunction in the PSG
(pump control unit).Fuel injection quantity is
reduced.EEPROM or A/D converter
no malfunction in the PSG
( p u m p c o n t r o l u n i t ) .
No recovery until in the next
ignition key cycle.PSG (pump control unit)
malfunction.
——
B ON Injection Pump Malfunction PSG (pump control unit)
recognized high pressure
solenoid valve drive circuit
error.No fail-safe function. No recovery until condition
match in the next ignition key
cycle.PSG (pump control unit)
malfunction.
——
D ON Injection Pump Malfunction PSG (pump control unit)
could not measure the high
pressure solenoid valve drive
voltage.PSG (pump control unit)
malfunction.
——
E ON Injection Pump Malfunction ECM could not accept PSG
(pump control unit) message.1. MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d .
2. Desired injection quantity
becomes 0mg/strk.ECM accepts PSG (pump
control unit) message.1. CAN high circuit open,
short to ground or short
t o v o l t a g e c i r c u i t .
2. CAN low circuit open,
short to ground or short
t o v o l t a g e c i r c u i t .
3 . E C M m a l f u n c t i o n .
4. PSG (pump control unit)
malfunction.9 9 /
100P1650(A)/











P1651(B) Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)

4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS 6E–119
43 P0335 B ON Crankshaft Position Sensor
Circuit Malfunction1. Engine speed is more
t h a n 6 6 5 r p m .
2. CKP sensor pulse width
error.When pump camshaft speed
sensor is OK:
ECM uses doubled pump
camshaft speed as substitute
engine speed.
When pump camshaft speed
s e n s o r i s n o t O K :
1. MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d .
2. Desired injection quantity
becomes 0mg/strk. ECM detects correct CKP
pulse width.1 . D u r i n g e n g i n e r u n :
1. CKP sensor harness
open circuit, short to
ground or short to
voltage circuit.
2. Poor connector
c o n n e c t i o n .
3. CKP sensor malfunction.
4. Pulse sensing gap
i n c o r r e c t .
5 . P u l s e r m a l f u n c t i o n .
6. Electrical interference.
7. Magnetic interference.
8. ECM malfunction.9 0 /
9 8 /
101P1335 (A)
D ON Crankshaft Position Sensor
Circuit Malfunction1. No pump camshaft
s p e e d s e n s o r e r r o r .
2. "Crankshaft Position
Sensor Circuit
Malfunction (Symptom
Code B)" is not stored.
3 . E n g i n e s p e e d i s 0 r p m .
4. Doubled pump camshaft
speed is more than
50rpm.When pump camshaft speed
s e n s o r i s O K :
ECM uses doubled pump
camshaft speed as substitute
engine speed.
Other than pump camshaft
s p e e d s e n s o r i s O K :
Fuel injection quantity is
reduced.1. Engine speed is more
than 0rpm.
2. Doubled pump camshaft
speed is below 100rpm.During engine crank:
1. CKP sensor harness
open circuit, short to
ground or short to
voltage circuit.
2. Poor connector
c o n n e c t i o n .
3. CKP sensor malfunction.
4. Pulse sensing gap
i n c o r r e c t .
5 . P u l s e r m a l f u n c t i o n .
6. Electrical interference.
7. Magnetic interference.
8. ECM malfunction.9 0 /
9 8 /
101P1135 (A)
E ON Engine Speed Input Circuit
Range/PerformanceEngine speed is more than
5700rpm.When intermittent
malfunction:
1. MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d .
2. Desired injection quantity
b e c o m e s 0 m g / s t r k .
When preliminary
malfunction:
ECM uses doubled pump
camshaft speed as substitute
engine speed.Engine speed is below
5700rpm.1. Engine over-running.
2. CKP sensor malfunction.























3 . P u l s e r m a l f u n c t i o n .
4. ECM malfunction.
9 0 /
9 8 /
101—
66 P0380 4 ON Glow Relay Circuit Voltage
LowGlow relay circuit open or
short to ground circuit.No fail-safe function. Glow relay circuit is correct
condition.1. Glow relay circuit open or
short to ground circuit.
2. Glow relay malfunction.
3. ECM malfunction.94 —
8 ON Glow Relay Circuit Voltage
HighGlow relay circuit short to
voltage circuit.ECM malfunction.
—— Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)

6E–122 4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS
35 P0560 A OFF System Voltage Malfunction System voltage of PSG
(pump control unit) is below
4.5V or more than 27V.PSG uses default voltage as
substitute.System voltage of PSG is
between 4.5V and 27V.1. Battery power feed
harness open circuit or
short to ground circuit.
2. PSG (pump control unit)
ground harness open or
p o o r c o n n e c t i o n .
3. Poor connector
c o n n e c t i o n .
4 . B a t t e r y m a l f u n c t i o n .
5. Charge system
m a l f u n c t i o n .
6. Battery jump start cable
misconnect.
7. PSG (pump control unit)
malfunction.——
18 P0561 A OFF Ignition Switch Circuit
MalfunctionThe ECM recognized ignition
switch turn off signal during
ECM is activated.ECM stops engine. No recovery until condition
match in the next ignition key
cycle.1. Ignition switch circuit
open or short to ground
c i r c u i t .
2. Poor connector
c o n n e c t i o n .
3. Ignition switch
m a l f u n c t i o n .
4. ECM malfunction.39 —
B OFF Ignition Switch Circuit
MalfunctionIgnition switch circuit is
malfunction.1. Ignition switch circuit
open or short to ground
c i r c u i t .
2. Poor connector
c o n n e c t i o n .
3. Ignition switch
m a l f u n c t i o n .
4. ECM malfunction.39 —
- P0602 - Control Module
Programming ErrorECM memory area error. Engine control disabled. Memory are is OK. ECM is not programmed.
——
28 P0606 A ON ECU Malfunction Gate Array communication
error.1. MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d .
2. Desired injection quantity
becomes 0mg/strk.No recovery. ECM malfunction.
——
B ON ECU Malfunction 1. Throttle position is below
1 % .
2. Desired injection quantity
is more than 0mg/strk.
3. Engine speed is more
t h a n 2 0 0 0 r p m . MAB (fuel cutoff solenoid
v a l v e ) i s o p e r a t e d . Desired injection quantity is
b e l o w 0 m g / s t r k . 1 . E C M m a l f u n c t i o n .
2. PSG (pump control unit)
malfunction.
—— Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)

6E–124 4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS
21 P1120 1 ON Pedal/Throttle Position
Sensor Circuit High InputThrottle position sensor
output voltage is more than
4.5V.ECM increases idle speed up
to 1400rpm.Throttle position sensor
output voltage is below 4.5V.1. Sensor power supply
circuit short to voltage
c i r c u i t .
2. Sensor signal circuit
short to voltage circuit.
3. Sensor ground circuit
open or short to voltage
c i r c u i t .
4. Poor connector
c o n n e c t i o n .
5 . T P S m a l f u n c t i o n .
6. ECM malfunction.3 8 /
4 9 /
57—
7 ON Pedal/Throttle Position
Sensor Voltage Supply
Circuit High InputThrottle position sensor
power supply voltage is more
than 5.2V.Throttle position sensor
power supply voltage is
below 5.2V.1. Sensor power supply
circuit short to battery
voltage circuit.
2 . T P S m a l f u n c t i o n .
3. ECM malfunction.57 —
9 ON Pedal/Throttle Position
Sensor Voltage Supply
Circuit Low InputThrottle position sensor
power supply voltage is
below 4.6V.Throttle position sensor
power supply voltage is more
than 4.6V.1. Sensor power supply
circuit short to ground
c i r c u i t .
2 . T P S m a l f u n c t i o n .
3. ECM malfunction.57 —
D ON Pedal/Throttle Position
Sensor Brake Switch Error1. Engine speed is more
t h a n 1 7 0 0 r p m .
2. Vehicle speed is more
t h a n 1 . 5 k m / h .
3. When brake pedal is
depressed during
accelerator pedal is
d e p r e s s i n g . Throttle position is more than
20% or brake pedal is
released (switch is inactive). 1 . T h r o t t l e s t i c k i n g .
2. TPS incorrect adjusting.
3 . T P S m a l f u n c t i o n .
4. Brake switch
m a l f u n c t i o n .
5. ECM malfunction.3 0 /
3 8 /
65—
E ON Pedal/Throttle Position
Sensor Idle Position Switch
Error1. When idle switch is
turned off, throttle
position sensor was
b e l o w 0 . 3 5 % .
o r
2. When idle switch is tuned
on, throttle position
sensor was more than
7.8%.1. When throttle position
sensor is 100%, idle
s w i t c h t u r n s o f f .
2. When throttle position
sensor is 0%, idle switch
turns on.1 . T P S m a l f u n c t i o n .
2. Idle switch malfunction.
3. ECM malfunction.
3 8 /
69—
22 P1173 3 OFF Fuel Reduction Caused By
High Coolant TemperatureExcessive high engine
coolant temperature is
detected.No fail-safe function. Engine coolant temperature
is normal range.1 . E n g i n e o v e r h e a t .
2. ECT sensor malfunction.








3. ECM malfunction.89 —
7 OFF Fuel Reduction Caused By
High Fuel TemperatureFuel temperature is more
than 100 deg. C.PSG (pump control unit)
controls fuel injection
quantity based on engine
speed and fuel temperature.Fuel temperature is below
100 deg. C.1 . E C M m a l f u n c t i o n .
2. PSG (pump control unit)
malfunction.——
A OFF Fuel Reduction Caused By
Low Fuel TemperatureExcessive low fuel
temperature is detected.No fail-safe function. Fuel temperature is normal
range.1 . E C M m a l f u n c t i o n .
2. PSG (pump control unit)
malfunction.——— Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)

4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS 6E–125
43 P1335 A ON Engine Speed Output Circuit
MalfunctionThe PSG (pump control unit)
is recognized defective
engine speed signal form the
ECM.Fuel injection quantity is
reduced.Correct engine speed signal. 1. CKP sensor harness
open circuit, short to
ground or short to
voltage.
2. CKP sensor output
harness open circuit,
short to ground or short
t o v o l t a g e .
3. Poor connector
c o n n e c t i o n .
4. CKP sensor malfunction.
5. Pulse sensing gap
i n c o r r e c t .
6 . P u l s e r m a l f u n c t i o n .
7. Electrical interference.
8. Magnetic interference.
9. ECM malfunction.
10. PSG (pump control unit)
malfunction.9 0 /
9 1 /
9 8 /
101P0335(B)/











P0335(D)
45 P1345 A ON Camshaft Speed Malfunction The PSG (pump control unit)
is recognized incorrect
camshaft speed signal.No fail-safe function. Correct camshaft speed. 1. Pump camshaft speed
s e n s o r m a l f u n c t i o n .
2. Pulse sensing gap
i n c o r r e c t .
3 . P u l s e r m a l f u n c t i o n .
4. Electrical interference.
5. Magnetic interference.
6. ECM malfunction.
7. PSG (pump control unit)
malfunction.——
47 P1520 A ON Neutral Switch ON Error Neutral switch signal is
inputted "On" three times
consecutively under driving
conditions.No fail-safe function. Correct neutral switch signal
is inputted two times
consecutively under driving
conditions.1. Neutral switch circuit
short to voltage circuit.
2. Neutral switch
m a l f u n c t i o n .
3. ECM malfunction.87 —
B ON Neutral Switch OFF Error Neutral switch signal is
inputted "Off" three times
consecutively under driving
conditions.1. Neutral switch circuit
open, short to ground
c i r c u i t .
2. Poor connector
c o n n e c t i o n .
3. Neutral switch
m a l f u n c t i o n .
4. ECM malfunction.87 — —
55 P1605 C ON Seed and Key File Destroyed Seed or key file in EEPROM
is destroyed.No fail-safe function. No recovery. ECM malfunction.
——
D ON EEPROM Defect Write and read from the
EEPROM are failed during
initialization of the ECM.ECM uses default values
from the EPROM.Write and read from the
EEPROM are correct during
initialization of the ECM.ECM malfunction.
—— Flash
CodeCodeSymptom
CodeMILDTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure PartsRelated
ECM Pin
No.Related
Multiple
DTC4JA1-TC
(MT)4JH1-TC
(MT)4JH1-TC
(AT)