2004 ISUZU TF SERIES Transmission

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-43

DTC P0712 (FLASHING CODE 15) Transmission Oil Temperature Sensor
Circuit Low Input

RTW37AMF000201
Circuit Description
The oil temperature sensor is a thermistor sensor that
is installed in the transmission case and converts
temperature changes into continuous electric signals,
then outputs them to the Transmission Control Module
(TCM). When the ATF temperature is low, the
resistance of the sensor (thermistor) goes up, so that
the voltage of the TCM signal becomes high.
As the ATF is gradually warmed, the resistance of the
sensor goes down and the voltage becomes low. At the
normal operating ATF temperature (80

C/176

F) of the
transmission, the voltage of the TCM is about 3.7V.
Condition for setting the DTC

The TCM detects following "Condition" for 5 min
continuously.
Condition ("Short"):

Oil temperature is more than 220

C (428

F).

Action Taken When The DTC Sets

The TCM judges oil temperature is 100

C (212

F).
 Check Trans ON.

DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.

7A2-44 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.
 Check oil temperature sensor for proper mounting
and adjustment.



DTC P0712 (FLASHING CODE 15) Transmission Oil Temperature Sensor
Circuit Low Input


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2 Perform the transmission fluid checking procedure.
Refer to checking Transmission Fluid level and
Condition in Automatic Transmission 7A section.
Was the fluid checking procedure performed ? — Go to Step 3 Refer to
Checking
Transmission
Fluid level and
Condition in
Automatic
Transmission
(AW30-40LE)
section
3

1. Install the scan tool.

2. Key “ON"
3. Review and record scan tool data.

4. Operate the vehicle with in scan tool data.
Does the scan tool indicate DTC P0712 ? — Go to Step 4 Refer to
Diagnostic Aids
4 Measure the voltage of the transmission fluid
temperature sensor by the J39200 DMM.

1. Key “OFF".
2. Disconnect the oil temperature sensor connector.

3. Key “ON".

4. Connect the J39200 DMM to the each terminal of
the oil temperature sensor connector E83-2 and
E83-1.
Does the scan tool indicate less than specified
value ? 5V Go to Step 5 Go to Step 6
5 Replace the transmission fluid temperature sensor.
Is the action complete ? — Verify repair —

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-45

Step Action Value(s) YES NO
6 Measure the resistance of the wire by the J39200
DMM.

1. Key “OFF".
2. Disconnect the TCM connector.

3. Install a jumper wire from terminal E83-1 and E83-
2 on the mission harness.

4. Connect the j39200 DMM to the each terminal of
the TCM connector C94-11 and C94-12.
If a problem is found, repair as necessary.
Was the problem found ? less than 1
Verify repair Go to Step 7
7 Replace the TCM.
Important:
The replacement TCM must be
programmed.
(Refer to SPS for procedure.)
Is the action complete ? — Verify repair —

7A2-46 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

DTC P0713 (FLASHING CODE 16) Transmission Oil Temperature Sensor
Circuit Hight Input

RTW37AMF000201
Circuit Description
The oil temperature sensor is a thermistor sensor that
is installed in the transmission case and converts
temperature changes into continuous electric signals,
then outputs them to the Transmission Control Module
(TCM). When the ATF temperature is low, the
resistance of the sensor (thermistor) goes up, so that
the voltage of the TCM signal becomes high.
As the ATF is gradually warmed, the resistance of the
sensor goes down and the voltage becomes low. At the
normal operating ATF temperature (80

C/176

F) of the
transmission, the voltage of the TCM is about 3.7V.
Condition for setting the DTC

The TCM detects following "Condition" for 15 min
from ignition ON.
Condition ("Open"):

Fluctuation of high temperature fixed value is
2.3

C (36

F).
 Fluctuation of low temperature fixed value is -10

C
(14
F).
Action Taken When The DTC Sets

The TCM judges oil temperature is 100

C (212

F).

Check Trans ON.
 DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4  (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-47

Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.

Check oil temperature sensor for proper mounting
and adjustment.

DTC P0713 (FLASHING CODE 16) Transmission Oil Temperature Sensor
Circuit Hight Input


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System Check performed ? — Go to Step 2 Go to OBD
System check
2 Perform the transmission fluid checking procedure.
Refer to Checking Transmission Fluid Level and
condition Automatic Transmission7A section.
Was the fluid checking procedure performed ? — Go to Step 3 Refer to
checking
Transmission
Fluid Level and
Condition
Automatic
Transmission
(AW30-40LE)
section
3

1. Install the scan tool ?

2. Key “ON"
3. Review and record scan tool date.

4. Operate the vehicle with in scan tool data.
Does the scan tool indicator DTC P0713 ? — Go to Step 4 Go to
Diagnostic Aids
4 Observe the voltage of the transmission fluid
temperature sensor on the TECH2 data.

1. Key “OFF".

2. Disconnect the transmission fluid temperature
sensor connector E-83
3. Install a fused jumper wire from terminal E83-2 to
E83-1 on the mission harness.

4. Key “ON".
Does the scan tool indicate more than specified
value ? 0.4V Go to Step 5 Go to Step 6
5 Replace the transmission fluid temperature sensor .
If the action complete ? — Verify repair —

7A2-48 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Step Action Value(s) YES NO
6 Measure the resistance of wire by the J39200 DMM.

1. Key “OFF".
2. Disconnect the TCM connector

3. Install a fused jumper wire from terminal E83-1
and E83-2 on the mission harness.
Does the scan tool indicate less than specified
value ? less than 1
Go to Step 8 Go to Step 7
7 Repair an open circuit.
Was the problem found ? — Verify repair —
8 Replace the TCM
IMPORTANT ; The replacement TCM must be
programmed. (Refer to SPS for procedure.)
Is the action complete ? — Verify repair —

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-49

DTC P0717 (FLASHING CODE 14) Input Speed Sensor Signal Error

MAW060MF001501

Circuit Description
Input revolution information is provided to TCM by the
input revolution sensor. This sensor is located in the
transmission case.
The input revolution sensor is an electromagnetic pulse
pickup type that generates a speed signal according to
the revolution of the transmission OD direct clutch
drum. As a result, the sensor sends a sine wave signal
(AC) to the TCM, which converts this sine wave signal
(pulse voltage) to a RPM signal.
Condition for setting the DTC
The TCM detects following conditions at 1000
times continuously.

When the TCM detects following conditions at the
same time.
 When output speed is over 775 rpm (16 mph) at
gear position is 1st or 2nd or 3rd.

Input speed signal is no pulse while output speed
signal are 12 pulses.

OR

When the TCM output 2nd gear.
 The TCM detects no pulse of input speed senso
r
circuit signal after 3.5 sec.
(detection time: 0.03 sec at vehicle speed is 36 mph)
Action Taken When The DTC Sets

No engine torque control.
 No line pressure control.

No lock-up control.

No slope control.

Check Trans ON.
 DTC stored.

No detect DTC P0722.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

7A2-50 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent shorto
r
open condition, move the wiring harness while
observing test equipment for a change.
 Check input speed sensor for proper mounting and
adjustment.


DTC P0717 (FLASHING CODE 14) Input Speed Sensor Signal Error


Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System check performed ? — Go to Step 2 Go to OBD
system check
2

1. Install the scan tool.

2. Key “ON".
3. Review and record scan tool data

4. Operate the vehicle with in scan tool data.
Does the scan tool indicator DTC0717 ? — Go to Step 3 Refer to
Diagnostic Aids
3 Measure voltage of the input revolution sensor by the
J39200 DMM.

1. Key “ON".
2. Engine run.

3. Disconnect the input revolution sensor connector .

4. Measure the voltage between terminal the input
revolution sensor connector E80-1 and E80-2.
Does the scan tool indicate less than specified
value ? 3V Refer to
Diagnostic Aids Go to Step 4