2004 ISUZU TF SERIES transmission oil

CONSTRUCTION AND FUNCTION 7A1-27
Item Description
- 4L mode -
4L mode setting condition
4L switch: On
Vehicle speed: More than 5km/h
Above conditions are met at the same time.
4L mode reset condition
4L switch: Off
Vehicle speed: Less than 4km/h
Above conditions are met at the same time.

- Down slope mode -
Down slope mode setting condition
Brake switch: On
Engine idle condition: More than 2.5 seconds
Select lever position: D or 3 range
Vehicle speed: More than 55km/h
Vehicle speed change: More than 1km/h
Above conditions are met at the same time.
Down slope mode reset condition
Engine idle condition: Not idle condition
Select lever position: Other than D or 3 range
At least, one of above conditions is met.

- Power Mode -
When power drive switch is On at only D range or 3 range, the shift change is performed by
1 – 4 speed based on shift diagram set as power pattern.

- Up slope mode -
Up-slope reasoning value is calculated from the average throttle angle and the average
acceleration. Otherwise, up-slope reasoning value is calculated from the vehicle speed.
TCM judges as up-slope mode when the former is bigger than latter.


Lock-up control The lock-up solenoid adjusts the pressure based on the signal from the TCM according to
the vehicle speed, throttle opening and other input signals based on the pre-set lock-up
point to control the lock-up.
Smooth lock-up control engages and disengages the clutch smoothly at the time of lock-up.
When the oil temperature is low (below 20
C) or high (above 128
C), lock-up is prohibited
even when the vehicle is at a lock-up speed.
The lock-up is disengaged also when the throttle is closed.
Direct electronic shift
control (DESC)
The duty cycle type solenoid is used for each clutch and brake. The solenoid adjusts the
clutch pressure to be suited to the engine load and vehicle traveling condition based on the
signal from the TCM. The pressure switch provided in the control valve oil passage sends
the oil pressure condition to the TCM to control the disengagement and engagement of the
clutch and brake directly and finely.
Learning control Learning is controlled to correct the oil pressure control timing to engage or disengage the
clutch optimally in order to compensate changes of the engine performance and changes
of the transmission with time. It is controlled to bring the speed-change time closer to the
value pre-set to the TCM.

CONSTRUCTION AND FUNCTION 7A1-33
LEARNING CONTROL

Oil pressure control timing is optimally corrected at the time of clutch engagement and disengagement
and controlled to bring the speed-change time to the value preset to the TCM and compensate the
changes of the engine performance and changes of the transmission with time.

When the gear is shifted, the clutch pressure 2 is optimally corrected so that the speed-change time is as
near as the target value
1 preset to the TCM and the changes in the engine performance and the
changes of the transmission with time can be compensated based on the past speed-change results.

When the clutch is operated to shift the gear, the time of the clutch oil pressure release timing 4 on the
disengagement side is optimally corrected so that the changes of the engine rpm
3 is optimum.


Note:

When the battery terminal is disconnected, contents of learning are cleared and resultantly the speed
change shock may increase. After the vehicle has traveled, learning is repeated and the shock
decreases gradually.





Figure 53. Learning Control

CONSTRUCTION AND FUNCTION 7A1-35
CONTROL CIRCUIT BLOCK DIAGRAM



Speed sensor
Turbine sensor
Brake switch
Inhibitor switch
Power drive, 3rd start
switch
ATF oil thermo sensor
High clutch oil pressure
switch
2-4 brake oil pressure
switch
Low & reverse brake oil
pressure switch
Transfer control module
(4WD Only)



Engine Control Module
(ECM)
Line pressure solenoid
Low clutch solenoid
High clutch solenoid
2-4 brake solenoid
Low & reverse brake
solenoid
Lock-up solenoid
ATF temperature
indicator lamp
Speed meter (2WD
Only)
Power, 3rd start indicator
lamp
Check trans indicator
lamp
Data link connector Self-diagnosis
function



Transmission
Control
Module
(TCM)
4L mode
Engine
speed
Throttle
angle
Figure 54. Control Circuit Block Diagram

7A1-36 CONSTRUCTION AND FUNCTION
GEAR TRAIN (TRANSMISSION MECHANISM) OPERATION AND
HYDRAULIC CIRCUIT
CONSTRUCTION AND OPERATION
The JR405E consists of two sets of planetary gears, three multiple plate clutches, two multiple plate brakes
and one one-way clutch.





COMPONENT NAME AND FUNCTION
Component Name Symbol Function
Low Clutch L/C Connects the front planetary carrier to the rear
internal gear.
Engaged at 1st, 2nd and 3rd gear.
High Clutch H/C Connects the input shaft to the front planetary
carrier.
Engaged at 3rd and 4th (O/D) gear.
Reverse Clutch R/C Connects the input shaft to the front sun gear.
Engaged at Reverse gear.
Low & Reverse Brake L&R/B Locks the front planetary carrier.
Engaged at L range and Reverse gear.
2-4 Brake 2-4/B Locks the front sun gear.
Engaged at 2nd and 4th (O/D) gear.
Low One-way Clutch L/O.C Allows the front planetary carrier to turn forward
(clockwise) but locks to opposite direction
(counterclockwise).
Operative when accelerating.
Low Clutch Solenoid L/C.S Regulates low clutch pressure.
High Clutch Solenoid H/C.S Regulates high clutch pressure.
Low & Reverse Brake Solenoid L&R/B.S Regulates low & reverse brake pressure.
2-4 Brake Solenoid 2-4/B.S Regulates 2-4 brake pressure.
Lock-up Solenoid L/U.S Regulates lock-up clutch pressure.
High Clutch Oil Pressure SW H/C.P/SW Detects high clutch supply oil pressure.
Low & Reverse Brake Oil Pressure SW L&R/B.P/SWDetects low & reverse brake supply oil pressure.
2-4 Brake Oil Pressure SW 2-4/B.P/SWDetects 2-4 brake supply oil pressure.

7A2-4 DIAGNOSIS (JR405E)
PAGE
NO. D3: GEAR SHIFT POINT IS LOW OR HIGH AT ALL POINT................................. 7A2-120
NO. D4: GEAR SHIFT POINT IS LOW OR HIGH AT LIMITED POINT ......................... 7A2-120
NO. D5: NO KICK-DOWN .............................................................................................. 7A2-120
NO. E1: NO GEAR SHIFT .............................................................................................. 7A2-121
NO. E2: ONLY 4TH GEAR (O/D) IS NOT SELECTABLE ............................................. 7A2-124
NO. E3: GEAR IS SHIFTED 2ND TO 3RD IN 2 RANGE ............................................... 7A2-126
NO. E4: GEAR IS SHIFTED 1ST TO 2ND IN L RANGE................................................ 7A2-126
NO. E5: GEAR IS SHIFTED 3RD TO 4TH IN 3 RANGE................................................ 7A2-126
NO. F1: LOW MAXIMUM SPEED OR POOR ACCELERATION ................................... 7A2-127
NO. F2: ENGINE RACES UP DURING ACCELERATION (SLIP) ................................. 7A2-130
NO. F3: NOISE OR VIBRATION DURING THE RUNNING IN R, D, 3, 2 OR L
RANGE .......................................................................................................................... 7A2-130
NO. F4: ENGINE BRAKE DOES NOT APPLY IN L RANGE......................................... 7A2-130
NO. F5: ENGINE STALLS BEFORE VEHICLE STOPS FROM RUNNING ................... 7A2-131
NO. G1: VEHICLE MOVES IN P RANGE OR PARKING GEAR IS NOT
DISENGAGED OTHER THAN P RANGE ..................................................................... 7A2-131
NO. G2: CREEP FORCE IS LARGE.............................................................................. 7A2-131
NO. G3: CREEP FORCE IS SMALL .............................................................................. 7A2-132
NO. G4: LARGE NOISE DURING IDLING WITH THE VEHICLE IN STOP STATE ...... 7A2-133
NO. H1: JUDDER OCCURS AT THE LOCK-UP ........................................................... 7A2-133
NO. H2: LARGE LOCK-UP SHOCK .............................................................................. 7A2-133
NO. H3: LOCK-UP POINT IS HIGH OR LOW ............................................................... 7A2-133
NO. I1: NO LOCK-UP .................................................................................................... 7A2-134
NO. J1: OIL LEAKS FROM BREATHER ....................................................................... 7A2-136
NO. J2: OIL LEAKS BETWEEN ENGINE AND CONVERTER HOUSING .................... 7A2-136
NO. J3: OIL LEAKS BETWEEN MAIN CASE AND CONVERTER HOUSING.............. 7A2-136
NO. J4: OIL LEAKS BETWEEN MAIN CASE AND REAR HOUSING .......................... 7A2-136
NO. J5: OIL LEAKS FROM OIL PAN ............................................................................ 7A2-136
NO. J6: OIL LEAKS FROM MANUAL SHAFT OIL SEAL ............................................. 7A2-136
NO. J7: OIL LEAKS FROM OIL COOLER PIPE JOINT................................................ 7A2-136
NO. Z1: TRANSMISSION OVERHEAT .......................................................................... 7A2-136
NO. Z2: MODE LAMP (POWER DRIVE OR 3RD START) DOES NOT LIGHT UP
WHEN THE POWER MODE OR 3RD START MODE IS TURNED ON........................ 7A2-137

7A2-12 DIAGNOSIS (JR405E)
F0: Diagnostic Trouble Code
F0: Read DTC Infor As Stored By ECU
F1: Clear DTC Information
F1: Data Display
F2: Snapshot
F3: Miscellaneous Test
F0: Lamp
F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmission Check Light Test
F1: Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid
F4: Programming
F0: Program VIN
F1: Lock ECU

F0: Diagnostic Trouble Code
The purpose of the "Diagnostic Trouble Codes" mode is to
display stored trouble code in the TCM.
When "Clear DTC Information" is selected, a "Clear DTC
Information", warning screen appears. This screen informs you
that by cleaning DTC's "all stored DTC information in the TCM
will be erased".
After clearing codes, confirm system operation by test driving
the vehicle.

F1: Data Display
The purpose of the "Data Display" mode is to continuously
monitor data parameters.
The current actual values of all important sensors and signals
in the system are display through F1mode.
See the "Typical Scan Data" section.

F2: Snapshot
"Snapshot" allows you to focus on making the condition occur,
rather than trying to view all of the data in anticipation of the
fault. The snapshot will collect parameter information around a
trigger point that you select.

F3: Miscellaneous Test:
The purpose of "Miscellaneous Test" mode is to check for
correct operation of electronic system actuators.

F4: Programming (Factory Use Only):
The purpose of "Programming" is to program VIN in the ECM
and lock the programmed data.

7A2-14 DIAGNOSIS (JR405E)
MISCELLANEOUS TEST
The state of each circuit can be tested by using miscellaneous test menus. Especially when DTC cannot be
detected, a faulty circuit can be diagnosed by testing each circuit by means of these menus.
Even DTC has been detected, the circuit tests using these menus could help discriminate between a mechanical
trouble and an electrical trouble.

Connect Tech 2 and select "Powertrain", "JR 405E" & "Miscellaneous Test".
F0: Lamps
The circuit is normal if the warning light in the meter panel comes on and goes out in accordance with Tech 2
instruction.

Lamps

F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Tempeature Lamp Test
F3: Transmission Check Light Test


F0: Power Lamp Test


Power Lamp Test

Power Lamp Off



 Press "Active" key.
Then, "POWER DRIVE" indicator lamp is turned on in the meter panel.
 Press "Inactive" key.
Then, "POWER DRIVE" indicator lamp is turned off in the
meter panel.
 Press "Quit" Key to cancel the test.
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmisstion Check Light Test
Test procedure is same as "F0: Power Lamp Test".
The circuit is normal if the warning light in the meter panel
comes on and goes out in accordance with Tech 2 instruction.

F1: Solenoids
The circuit is normal if clicking sound is generated in accordance with Tech 2 instruction.

Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid

DIAGNOSIS (JR405E) 7A2-77
Step Action Yes No
6 Is the quantity of ATF correct?
Go to Step 7
Correct the quantity of
ATF.
Go to Step 9
7 Connect the Tech 2 and test the solenoids of respective
solenoids for low & reverse brake, 2-4 brake, high clutch and
low clutch. Is operation sound heard from each solenoid?
Go to Step 8
Replace the solenoid
that does not generate
the operation sound.
Go to Step 9
8 Check the line pressure during the idling and at the engine stall
speed. Is the line pressure correct?
Go to Step 10
Either control valve, oil
pump or power train
parts (clutch, brake)
will be faulty. Replace
or overhaul the
transmission unit.
Go to step 10
9 Run the vehicle, and is the gear shifted from 1st to 4th
correctly?
Go to Step 10
Either control valve, oil
pump or power train
parts (clutch, brake)
will be faulty. Replace
or overhaul the
transmission unit.
Go to step 10
10 Clear the DTC from the memory and perform the work after
repair. Is the same DTC code outputted again in the
subsequent DTC check?
Replace the TCM Go to Step 11
11 Are the other DTCs outputted?
Go to Other DTC
Section Action is completed