2004 INFINITI QX56 Revers

ASSEMBLY
AT-313
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
22. Measure clearance between retaining plate and snap ring. If not
within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:

Take care with the direction of needle baering. Refer to
AT-271, "
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings" .

Apply petroleum jelly to needle bearing.
SCIA5249E
SCIA2439E
Specified clearance “A”:
Standard: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate:
Refer to AT-333, "
Reverse brake" .
SCIA5341E
SCIA5213E

AT-318
ASSEMBLY
Revision: August 20072004 QX56
36. Install direct clutch assembly in reverse brake.
37. Install high and low reverse clutch assembly in direct clutch
assembly.
38. Using a flat-bladed screwdriver, range the drive plate.
39. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
SCIA5019E
SCIA2306E
SCIA3169E
SCIA5018E

ASSEMBLY
AT-319
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
CAUTION:
Check that portion A of high and low reverse clutch drum
protrudes approximately 2 mm (0.08 in) beyond portion B of
rear sun gear.
40. Install needle bearing in rear carrier assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
41. Install bearing race in rear carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
42. Install rear carrier assembly in direct clutch drum.
SCIA3130E
SCIA5179E
SCIA5178E
SCIA2462E

SERVICE DATA AND SPECIFICATIONS (SDS)
AT-331
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsUCS002J T
*1: Refer to MA-10, "Fluids and Lubricants" .
Vehicle Speed When Shifting GearsUCS002JU
NORMAL MODE

At half throttle, the accelerator opening is 4/8 of the full opening.
TOW MODE

At half throttle, the accelerator opening is 4/8 of the full opening. Applied model 4x2 4x4
Automatic transmission model RE5R05A
Transmission model code number 95X13 95X14
Stall torque ratio2.0: 1
Transmission gear ratio1st 3.827
2nd 2.368
3rd 1.519
4th 1.000
5th 0.834
Reverse 2.613
Recommended fluid NISSAN Matic Fluid J*1
Fluid capacity 10.6 liter (11-1/4 US qt, 9-3/8 Imp qt)
CAUTION:

Use only Genuine NISSAN ATF Matic Fluid J. Do not mix with other fluid.

Using automatic transmission fluid other than Genuine NISSAN an ATF Matic Fluid J will deteriorate in driveability and
automatic transmission durability, and may damage the automatic transmission, which is not covered by the warranty.
Final
gear
ratioThrottle positionVehicle speed km/h (MPH)
D
1 →D2D2 →D3D3 →D4D4 →D5D5 →D4D4 →D3D3 →D2D2 →D1
2.937Full throttle 70 - 74
(44 - 46)112 - 120
(70 - 75)176 - 186
(110 - 116)249 - 259
(155 - 161)245 - 255
(152 - 159)166 - 176
(103 - 110)100 - 108
(62 - 67)43 - 47
(27 - 30)
Half throttle 46 - 50
(28 - 31)74 - 82
(46 - 51)103 - 113
(64 - 70)135 - 145
(84 - 90)109 - 119
(68 - 74)69 - 79
(43 - 49)44 - 52
(27 - 32)11 - 1 5
(7 - 10)
3.357Full throttle 61 - 65
(38 - 41)97 - 105
(61 - 66)153 - 163
(95 - 102)236 - 246
(147 - 153)232 - 242
(144 - 151)143 - 153
(89 - 95)87 - 95
(54 - 59)43 - 47
(27 - 29)
Half throttle 41 - 45
(26 - 28)66 - 74
(41 - 46)89 - 99
(56 - 62)117 - 127
(73 - 79)95 - 105
(59 - 65)59 - 69
(37 - 43)38 - 46
(24 - 29)11 - 1 5
(7 - 10)
Final
gear
ratioThrottle positionVehicle speed km/h (MPH)
D
1 →D2D2 →D3D3 →D4D4 →D5D5 →D4D4 →D3D3 →D2D2 →D1
2.937Full throttle 70 - 74
(44 - 46)112 - 120
(70 - 75)176 - 186
(110 - 116)249 - 259
(155 - 161)245 - 255
(152 - 159)166 - 176
(103 - 110)100 - 108
(62 - 67)43 - 47
(27 - 30)
Half throttle 50 - 54
(31 - 34)81 - 89
(50 - 55)113 - 123
(70 - 76)135 - 145
(84 - 90)109 - 119
(68 - 74)68 - 78
(42 - 48)44 - 52
(27 - 32)11 - 1 5
(7 - 10)
3.357Full throttle 61 - 65
(38 - 41)97 - 105
(61 - 66)153 - 163
(95 - 102)236 - 246
(147 - 153)232 - 242
(144 - 151)143 - 153
(89 - 95)87 - 95
(54 - 59)43 - 47
(27 - 29)
Half throttle 43 - 47
(27 - 29)72 - 80
(45 - 50)98 - 108
(61 - 67)117 - 127
(73 - 79)95 - 105
(59 - 65)59 - 69
(37 - 43)37 - 45
(23 - 28)11 - 1 5
(7 - 10)

SERVICE DATA AND SPECIFICATIONS (SDS)
AT-333
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Reverse brakeUCS002K2
*: Always check with the Parts Department for the latest parts information.
Total End PlayUCS002K3
BEARING RACE FOR ADJUSTING TOTAL END PLAY
*: Always check with the Parts Department for the latest parts information.Thickness of retaining platesThickness mm (in) Part number*
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205) 31667 90X14
31667 90X15
31667 90X16
31667 90X17
31667 90X18
31667 90X19
Total end play mm (in) 0.25 - 0.55 (0.0098 - 0.0217)
Thickness mm (in) Part number*
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.4 (0.055)
1.6 (0.063)
1.8 (0.071)31435 95X00
31435 95X01
31435 95X02
31435 95X03
31435 95X04
31435 95X05

CONTROL UNIT
ATC-135
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
CONTROL UNITPFP:27500
Removal and InstallationEJS002CW
FRONT AIR CONTROL
Removal
1. Remove the five control knobs from the front air control unit.
2. Remove the cluster lid C. Refer to IP-12, "
Cluster Lid C" .
3. Remove the four screws securing the front air control unit to
cluster lid C.
4. Remove the front air control unit.
Installation
Installation is in the reverse order of removal.
REAR AIR CONTROL
Removal
1. Remove the overhead console from the headliner. Refer to EI-37, "HEADLINING" .
2. Remove the four screws and remove the rear air control.
Installation
Installation is in the reverse order of removal.
LJIA0130E
LJIA0131E

ATC-136
AMBIENT SENSOR
Revision: August 20072004 QX56
AMBIENT SENSORPFP:27722
Removal and InstallationEJS002CX
REMOVAL
1. Disconnect the ambient sensor electrical connector.
NOTE:
The ambient sensor is located behind the front bumper, in front
of the condenser.
2. Release the ambient sensor clip and then remove the ambient
sensor.
INSTALLATION
Installation is in the reverse order of removal.
WJIA0819E

IN-VEHICLE SENSOR
ATC-137
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
IN-VEHICLE SENSORPFP:27720
Removal and InstallationEJS002CY
REMOVAL
1. Remove the cluster lid D. Refer to IP-12, "Cluster Lid D" .
2. Remove the two screws and remove the in-vehicle sensor.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0132E