2004 INFINITI QX56 Revers

DTC P1846 ATF PRESSURE SWITCH 6
AT-185
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Diagnostic ProcedureUCS002IB
1. CHECK INPUT SIGNAL
With CONSULT-II
1. Start the engine.
2. Select “ECU INPUT SIGNALS” or “MAIN SIGNALS” in “DATA
MONITOR” mode for “A/T” with CONSULT-II.
3. Drive vehicle in the “D” position (2nd

3rd gear), and confirm
the ON/OFF actuation of the “ATF PRES SW 6”.
OK or NG
OK >> GO TO 6.
NG >> GO TO 2.
2. CHECK TCM
Perform TCM input/output signals inspection. Refer to AT-90, "
TCM Input/Output Signal Reference Values" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 5.
3. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 1 8 4 , "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector pin terminals for damage or loose connection with harness connec-
tor.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT - 2 4 1 , "Control Valve With TCM and A/T Fluid
Temperature Sensor 2" .
NG >> Repair or replace damaged parts.
5. DETECT MALFUNCTIONING ITEM
Check the following items:

Power supply and ground circuit for TCM.

The A/T assembly harness connector pin terminals for damage or loose connection with harness connec-
tor.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
Item name Condition Display value (ON-
OFF display)
ATF PRES
SW 6High and low reverse clutch engaged.
Refer to AT-2 1
.ON
High and low reverse clutch disengaged.
Refer to AT-2 1
.OFF
PCIA0067E

AT-198
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
Vehicle Does Not Creep Backward In “R” PositionUCS002IN
SYMPTOM:
The vehicle does not creep in the “R” position. Or an extreme lack of acceleration is observed.
DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" .
Do the self-diagnostic results indicate accelerator pedal position sensor, ATF pressure switch 6, high and low
reverse clutch solenoid valve, CAN communication line, PNP switch?
YES >> Check the malfunctioning system. Refer to AT - 1 2 9 , "DTC P1705 THROTTLE POSITION SEN-
SOR" , AT - 1 8 4 , "DTC P1846 ATF PRESSURE SWITCH 6" , AT-163, "DTC P1767 HIGH AND
LOW REVERSE CLUTCH SOLENOID VALVE" , AT-103, "DTC U1000 CAN COMMUNICATION
LINE" , AT-109, "DTC P0705 PARK/NEUTRAL POSITION SWITCH" .
NO >> GO TO 2.
2. CHECK CONTROL CABLE
Check the control cable.

Refer to AT-234, "Checking of A/T Position" .
OK or NG
OK >> GO TO 3.
NG >> Adjust control cable. Refer to AT-234, "
Adjustment of A/
T Position" .
3. CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to AT-13, "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.
4. CHECK STALL TEST
Check stall revolution with selector lever in “1” and “R” positions.
Refer to AT-58, "
STALL TEST" .
OK or NG
OK >> GO TO 6.
OK in “1” position, NG in “R” position>>GO TO 5.
NG in both “1” and “R” positions>>GO TO 8.
LCIA0324E
SAT6 3 8A
SAT4 9 3G

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-199
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
5. DETECT MALFUNCTIONING ITEM
1. Disassemble A/T. Refer to AT- 2 7 3 , "
Disassembly" .
2. Check the following items:
–Reverse brake. Refer to AT-273, "Disassembly" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
6. CHECK LINE PRESSURE
Check the line pressure with the engine idling. Refer to AT-59, "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 9.
NG - 1 >> Line pressure high. GO TO 7.
NG - 2 >> Line pressure low. GO TO 8.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-241, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 7 3 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
8. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-241, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 7 3 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
–Power train system. Refer to AT- 2 7 3 , "Disassembly" .
–Transmission case. Refer to AT - 2 7 3 , "Disassembly" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
SAT4 9 4G

AT-208
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
10. PERFORM TCM INSPECTION
1. Perform TCM input/output signals inspection. Refer to AT- 9 0 , "
TCM Input/Output Signal Reference Val-
ues" .
2. If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK >>INSPECTION END
NG >> Repair or replace damaged parts.
11 . DETECT MALFUNCTIONING ITEM

Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-68,
"Symptom Chart" (Symptom No.10).
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
A/T Does Not Shift: D2 → D3UCS002IR
SYMPTOM:
The vehicle does not shift-up from D2 to D3 gear at the specified speed.
DIAGNOSTIC PROCEDURE
1. CONFIRM THE SYMPTOM
Check if vehicle creeps forward in “D” position and vehicle can be started from D
1.
OK or NG
OK >> GO TO 2.
NG >> Refer to AT-201, "
Vehicle Does Not Creep Forward In “D” Position" , AT - 2 0 3 , "Vehicle Cannot Be
Started From D1" .
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" .
Do the self-diagnostic results indicate ATF pressure switch 6, high and low reverse clutch solenoid valve,
accelerator pedal position sensor, vehicle speed sensor A/T (revolution sensor) and vehicle speed sensor
MTR?
YES >> Check the malfunctioning system. Refer to AT-184, "DTC P1846 ATF PRESSURE SWITCH 6" ,
AT-163, "
DTC P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID VALVE" , AT-129, "DTC
P1705 THROTTLE POSITION SENSOR" , AT- 11 2 , "DTC P0720 VEHICLE SPEED SENSOR A/T
(REVOLUTION SENSOR)" , AT-136, "DTC P1721 VEHICLE SPEED SENSOR MTR" .
NO >> GO TO 3.
3. CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to AT-13, "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.
SAT6 3 8A

AT-234
SHIFT CONTROL SYSTEM
Revision: August 20072004 QX56
REMOVAL
1. Remove the select lever knob.
2. Remove console finisher.

Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
3. Remove center console.

Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
4. Disconnect selector control cable.
5. Disconnect A/T device harness connector.
6. Remove control device assembly.
INSTALLATION
Installation is in reverse order of removal.
NOTE:


: Vehicle front
Apply adhesive, Cemedyne 3000 or equivalent, to thread of select
lever knob before installation. Rotate knob clockwise through com-
plete thread range (A) at low torque. When knob rotation is finished
through complete thread range, rotation torque will sunddenly
increase. Continue knob rotation in incomplete thread range (B), not
more than 360°, until knob rotational position is as shown.

After installation is completed, adjust and check A/T position.
Adjustment of A/T PositionECS0090O
1. Loosen nut of control cable.
2. Place PNP switch and selector lever in “P” position.
3. After pushing the control cable in the direction shown with a
force of 9.8 N·m (1kg-m, 2.2 lb-ft), release it. This is in the natu-
ral state, tighten control cable nut to specifications.
Checking of A/T PositionECS0090P
1. Place selector lever in “P” position, and turn ignition switch ON
(engine stop).
2. Make sure selector lever can be shifted to other than “P” posi-
tion when brake pedal is depressed. Also make sure selector
lever can be shifted from “P” position only when brake pedal is
depressed.
3. Move the selector lever and check for excessive effort, sticking,
noise or rattle.
4. Confirm the selector lever stops at each position with the feel of
engagement when it is moved through all the positions. Check
whether or not the actual position the selector lever is in
matches the position shown by the shift position indicator and
the transmission body.
5. The method of operating the lever to individual positions correctly should be as shown.
6. Confirm the back-up lamps illuminate only when lever is placed in the “R” position. Confirm the back-up
lamps does not illuminate when selector lever is pushed against “R” position in the “P” or “N” position.
LCIA0323E
LCIA0397E
Control cable nut : 14.5 N·m (1.5 kg-m, 11 ft-lb)
LCIA0345E
LCIA0325E

TRANSMISSION ASSEMBLY
AT-257
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
INSTALLATION
Installation of the remaining components is in the reverse order of
the removal, while paying attention to the following work.

If removed install drive plate.
–Align dowel pin of crankshaft rear end with pin holes of each
parts to install.
–Install drive plate, reinforcement plate and pilot converter as
shown.
–Face chamfered or rounded edge side to crankshaft.
CAUTION:

When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.

Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.

When installing transmission to the engine, attach the bolts in
accordance with the following standard.
*: No.2 bolt also secures air breather vent.
–Align the positions of tightening bolts for drive plate with those of
the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.
CAUTION:

When turning crankshaft, turn it clockwise as viewed from the front of the engine.

After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that
transmission rotates freely without binding.

After completing installation, check fluid leakage, fluid level, and the positions of A/T. Refer to AT-13,
"Checking A/T Fluid" , AT-234, "Checking of A/T Position" , AT-234, "Adjustment of A/T Position" .
KBIA2494E
KBIA2537E
Bolt No. 1 2* 3
Number of bolts 4 1 4
Bolt length
“”mm (in)70 (2.76) 70 (2.76) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb)11 3
(12, 83)11 3
(12, 83)
LCIA0371E
LCIA0335E

AT-260
TRANSMISSION ASSEMBLY
Revision: August 20072004 QX56
INSTALLATION
Installation of the remaining components is in the reverse order of
the removal, while paying attention to the following work.

If removed, install drive plate.
–Align dowel pin of crankshaft rear end with pin holes of each
parts to install.
–Install drive plate, reinforcement plate and pilot converter as
shown.
–Face chamfered or rounded edge side to crankshaft.
CAUTION:

When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.

Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.

When installing transmission to the engine, attach the bolts in
accordance with the following standard.
*: No.2 bolt also secures air breather vent.
–Align the positions of tightening bolts for drive plate with those of
the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.
CAUTION:

When turning crankshaft, turn it clockwise as viewed from the front of the engine.

After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that
transmission rotates freely without binding.

After completing installation, check fluid leakage, fluid level, and the positions of A/T. Refer to AT-13,
"Checking A/T Fluid" , AT-234, "Checking of A/T Position" , AT-234, "Adjustment of A/T Position" .
KBIA2494E
KBIA2537E
Bolt No. 1 2* 3
Number of bolts 4 1 4
Bolt length
“”mm (in)70 (2.76) 70 (2.76) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb)11 3
(12, 83)11 3
(12, 83)
LCIA0371E
LCIA0335E

AT-262
OVERHAUL
Revision: August 20072004 QX56
1. O-ring 2. Oil pump cover 3. O-ring
4. Oil pump housing 5. Self-sealing bolt 6. Torque converter
7. Converter housing 8. Oil pump housing oil seal 9. Bearing race
10. Needle bearing 11. O-ring 12. Front carrier assembly
13. Needle bearing 14. Snap ring 15. Front sun gear
16. 3rd one-way clutch 17. Snap ring 18. Bearing race
19. Needle bearing 20. Seal ring 21. Input clutch assembly
22. Needle bearing 23. Rear internal gear 24. Brake band
25. Mid carrier assembly 26. Needle bearing 27. Bearing race
28. Rear carrier assembly 29. Needle bearing 30. Mid sun gear
31. Seal ring 32. Rear sun gear 33. 1st one-way clutch
34. Snap ring 35. Needle bearing 36. High and low reverse clutch hub
37. Snap ring 38. Bearing race 39. Needle bearing