2004 INFINITI FX35 Lock

TROUBLE DIAGNOSIS
AT-73
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
23
Slips/Will
Not
EngageVehicle cannot be
started from D
1 .
Refer to AT-203,
"Vehicle Cannot Be
Started From D1" .ON vehicle1. Fluid level and stateAT- 5 1
2. Accelerator pedal position sensorAT-136
3. Line pressure testAT- 5 2
4. CAN communication lineAT-105
5. Control valve with TCMAT-242
OFF vehicle6. Torque converterAT-286
7. Oil pump assemblyAT-303
8. 3rd one-way clutchAT-306
9. 1st one-way clutch AT-314
10. Gear systemAT-274
11. Reverse brakeAT-286
12. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 7 , "
Cross-Sectional View (2WD Models)" or AT- 1 8 ,
"Cross-Sectional View (AWD Models)" )AT-286
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17,
"Cross-Sectional View (2WD Models)" or AT-18, "Cross-
Sectional View (AWD Models)" )AT-286
24Does not lock-up.
Refer to AT-216, "A/T
Does Not Perform
Lock-up" .ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Engine speed signalAT-121
4. Turbine revolution sensorAT-143
5. Torque converter clutch solenoid valveAT-123
6. CAN communication lineAT-105
7. Control valve with TCMAT-242
OFF vehicle8. Torque converterAT-2869. Oil pump assemblyAT-303
25Does not hold lock-up
condition.
Refer to AT-218, "A/T
Does Not Hold Lock-
up Condition" .ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Engine speed signalAT-121
4. Turbine revolution sensorAT-143
5. Torque converter clutch solenoid valveAT-123
6. CAN communication lineAT-105
7. Control valve with TCMAT-242
OFF vehicle8. Torque converterAT-2869. Oil pump assemblyAT-303
No. Items Symptom Condition Diagnostic ItemReference
page

AT-74
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
26
Slips/Will
Not
engageLock-up is not
released.
Refer to AT-220,
"Lock-up Is Not
Released" .ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Engine speed signalAT- 1 2 1
4. Turbine revolution sensorAT- 1 4 3
5. Torque converter clutch solenoid valveAT- 1 2 3
6. CAN communication lineAT- 1 0 5
7. Control valve with TCMAT- 2 4 2
OFF vehicle8. Torque converterAT- 2 8 69. Oil pump assemblyAT- 3 0 3
27No shock at all or the
clutch slips when
vehicle changes
speed D
1 → D2 or
M
1 → M2 . ON vehicle1. Fluid level and stateAT- 5 1
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT- 1 4 5
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 2,
AT- 1 6 0
4. CAN communication lineAT- 1 0 5
5. Line pressure testAT- 5 2
6. Control valve with TCMAT- 2 4 2
OFF vehicle7. Torque converterAT- 2 8 6
8. Oil pump assemblyAT- 3 0 3
9. 3rd one-way clutchAT- 3 0 6
10. Gear systemAT- 2 7 4
11. Direct clutchAT- 3 2 3
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17,
"Cross-Sectional View (2WD Models)" or AT- 1 8 , "Cross-
Sectional View (AWD Models)" )AT- 2 8 6
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-81
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
40
Slips/Will
Not
EngageWhile accelerating in
4th, engine races or
slippage occurs.ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Accelerator pedal position sensorAT-136
4. CAN communication lineAT-105
5. ATF pressure switch 3 and input clutch solenoid valveAT-180,
AT-152
6. Control valve with TCMAT-242
OFF vehicle7. Torque converterAT-286
8. Oil pump assemblyAT-303
9. Input clutchAT-308
10. Gear systemAT-274
11. High and low reverse clutchAT-320
12. Direct clutchAT-323
41 While accelerating in
5th, engine races or
slippage occurs.ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Accelerator pedal position sensorAT-136
4. CAN communication lineAT-105
5. ATF pressure switch 1 and front brake solenoid valveAT-178,
AT-156
6. Control valve with TCMAT-242
OFF vehicle7. Torque converterAT-286
8. Oil pump assembly AT-303
9. Front brake (brake band)AT-286
10. Input clutchAT-308
11. Gear systemAT-274
12. High and low reverse clutchAT-320
42 Slips at lock-up.ON vehicle1. Fluid level and stateAT- 5 1
2. Line pressure testAT- 5 2
3. Engine speed signalAT-121
4. Turbine revolution sensorAT-143
5. Torque converter clutch solenoid valveAT-123
6. CAN communication lineAT-105
7. Control valve with TCMAT-242
OFF vehicle8. Torque converterAT-2869. Oil pump assemblyAT-303
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-85
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
53
OthersShift point is low in D
position.ON vehicle1. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6
,
AT-145
2. Accelerator pedal position sensorAT-136
3. CAN communication lineAT-105
4. Control valve with TCMAT-242
54Judder occurs during
lock-up.ON vehicle1. Fluid level and stateAT- 5 1
2. Engine speed signalAT-121
3. Turbine revolution sensorAT-143
4. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 6,
AT-145
5. Accelerator pedal position sensorAT-136
6. CAN communication lineAT-105
7. Torque converter clutch solenoid valveAT-123
8. Control valve with TCMAT-242
OFF vehicle 9. Torque converterAT-286
55Strange noise in R
position.ON vehicle1. Fluid level and stateAT- 5 1
2. Engine speed signalAT-121
3. CAN communication lineAT-105
4. Control valve with TCMAT-242
OFF vehicle5. Torque converterAT-286
6. Oil pump assemblyAT-303
7. Gear systemAT-274
8. High and low reverse clutchAT-320
9. Reverse brakeAT-286
56Strange noise in N
position.ON vehicle1. Fluid level and stateAT- 5 1
2. Engine speed signalAT-121
3. CAN communication lineAT-105
4. Control valve with TCMAT-242
OFF vehicle5. Torque converterAT-2866. Oil pump assemblyAT-303
7. Gear systemAT-274
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-91
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
CONSULT-IIACS007AI
After performing AT- 1 0 3 , "Diagnostic Procedure Without CONSULT-II" , place check marks for results on the
AT- 4 6 , "
DIAGNOSTIC WORKSHEET" . Reference pages are provided following the items.
NOTICE:
1. The CONSULT-II electrically displays shift timing and lock-up timing (that is operation timing of each sole-
noid).
Check for time difference between actual shift timing and the CONSULT-II display. If the difference is
noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical
parts using applicable diagnostic procedures.
2. Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Man-
ual may differ slightly. This occurs because of the following reasons:
–Actual shift schedule has more or less tolerance or allowance,
–Shift schedule indicated in Service Manual refers to the point where shifts start, and
–Gear position displayed on CONSULT-II indicates the point where shifts are completed.
3. Display of solenoid valves on CONSULT-II changes at the start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
4. Additional CONSULT-II information can be found in the Operation Manual supplied with the CONSULT-II
unit.
FUNCTION
CONSULT-II REFERENCE VALUE
Diagnostic test mode Function Reference page
Self-diagnostic results Self-diagnostic results can be read and erased quickly.AT- 9 4
Data monitor Input/Output data in the ECU can be read.AT- 9 7
CAN diagnostic support
monitorThe results of transmit/receive diagnosis of CAN communication can be read. —
Function testConducted by CONSULT-II instead of a technician to determine whether each system
is “OK” or “NG”.—
DTC work support Select the operating condition to confirm Diagnosis Trouble Codes.AT-100
ECU part number ECU part number can be read. —
Item name Condition Display value (Approx.)
ATF TEMP SE 1
0°C (32° F) - 20°C (68°F) - 80°C (176°F)2.2 - 1.8 - 0.6 V
ATF TEMP SE 22.2 - 1.7 - 0.45 V
TCC SOLENOIDWhen perform slip lock-up 0.2 - 0.4 A
When perform lock-up 0.4 - 0.6 A
SLCT LVR POSISelector lever in “N”,“P” position. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
VHCL/S SE·A/T During drivingApproximately matches the speedome-
ter reading.
ENGINE SPEED Engine runningClosely matches the tachometer read-
ing.
LINE PRES SOL During driving 0.2 - 0.6 A
TURBINE REV During driving (lock-up ON)Approximately matches the engine
speed.
VHCL/S SE·MTR During drivingApproximately matches the speedome-
ter reading.
ATF PRES SW 1Front brake engaged. Refer to AT- 2 0
.ON
Front brake disengaged. Refer to AT- 2 0
.OFF

AT-94
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
SELF-DIAGNOSTIC RESULT MODE
Operation Procedure
1. Perform “CONSULT-II SETTING PROCEDURE” Refer to AT- 9 3 ,
"CONSULT-II SETTING PROCEDURE" .
2. Touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing
operation.
Display Items List
X: Applicable, —: Not applicable
SCIA5304E
Items (CONSULT-
II screen terms)Malfunction is detected when...TCM self-diagnosis OBD-II (DTC)
A/T CHECK
indicator
lamp “A/T” with
CONSULT-IIMIL indicator
lamp*1,
“ENGINE” with
CONSULT-II or
GST
CAN COMM CIR-
CUIT

When a malfunction is detected in CAN communications X U1000 U1000
STARTER RELAY/
CIRC

If this signal is ON other than in P or N position, this is
judged to be a malfunction.
(And if it is OFF in P or N position, this too is judged to be a
malfunction.)X P0615 —
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern

P position is detected from N position without any other
position being detected in between.X P0705 P0705
VEH SPD SEN/
CIR AT (Revolution
sensor)

Signal from vehicle speed sensor A/T (Revolution sensor)
not input due to cut line or the like

Unexpected signal input during running

After ignition switch is turned ON, unexpected signal input
from vehicle speed sensor MTR before the vehicle starts
movingX P0720 P0720
ENGINE SPEED
SIG

TCM does not receive the CAN communication signal from
the ECM.X P0725 P0725*3
TCC SOLENOID/
CIRC

Normal voltage not applied to solenoid due to cut line,
short, or the likeX P0740 P0740
A/T TCC S/V
FNCTN

A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value
with slip rotation.X P0744 P0744*2
L/PRESS SOL/
CIRC

Normal voltage not applied to solenoid due to cut line,
short, or the like

TCM detects as irregular by comparing target value with
monitor value.X P0745 P0745
TCM-POWER
SUPPLY

When the power supply to the TCM is cut “OFF”, for exam-
ple because the battery is removed, and the self-diagnos-
tics memory function stops

This is not a malfunction message (Whenever shutting
“OFF” a power supply to the TCM, this message appears
on the screen.)— P1701 —
TCM·RAM

TCM memory (RAM) is malfunctioning. — P1702 —
TCM·ROM

TCM memory (ROM) is malfunctioning. — P1703 —

TROUBLE DIAGNOSIS
AT-95
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
TCM·EEPROM
TCM memory (EEP ROM) is malfunctioning. — P1704 —
TP SEN/CIRC A/T

TCM does not receive the proper accelerator pedal position
signals (input by CAN communication) from ECM.X P1705 P1705*3
ATF TEMP SEN/
CIRC

During running, the ATF temperature sensor signal voltage
is excessively high or lowX P1710 P0710
TURBINE REV S/
CIRC

TCM does not receive the proper voltage signal from the
sensor.

TCM detects an irregularity only at position of 4th gear for
turbine revolution sensor 2.X P1716 P1716
VEH SPD SE/
CIR·MTR

Signal (CAN communication) from vehicle speed sensor
MTR not input due to cut line or the like

Unexpected signal input during running— P1721 —
A/T INTERLOCK

Except during shift change, the gear position and ATF pres-
sure switch states are monitored and comparative judge-
ment made.X P1730 P1730
A/T 1ST E/BRAK-
ING

Each ATF pressure switch and solenoid current is moni-
tored and if a pattern is detected having engine braking 1st
gear other than in the M1 position, a malfunction is
detected.X P1731 —
I/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional
malfunction, cut line, short, or the like

TCM detects as irregular by comparing target value with
monitor value.X P1752 P1752
I/C SOLENOID
FNCTN

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure
switch 3 is irregular during depressing accelerator pedal.
(Other than during shift change)

TCM detects that relation between gear position and condi-
tion of ATF pressure switch 3 is irregular during releasing
accelerator pedal. (Other than during shift change)X P1754 P1754*2
FR/B SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional
malfunction, cut line, short, or the like

TCM detects as irregular by comparing target value with
monitor value.X P1757 P1757
FR/B SOLENOID
FNCT

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure
switch 1 is irregular during depressing accelerator pedal.
(Other than during shift change)

TCM detects that relation between gear position and condi-
tion of ATF pressure switch 1 is irregular during releasing
accelerator pedal. (Other than during shift change)X P1759 P1759*2
D/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to cut line,
short, or the like

TCM detects as irregular by comparing target value with
monitor value.X P1762 P1762 Items (CONSULT-
II screen terms)Malfunction is detected when...TCM self-diagnosis OBD-II (DTC)
A/T CHECK
indicator
lamp “A/T” with
CONSULT-IIMIL indicator
lamp*1,
“ENGINE” with
CONSULT-II or
GST

AT-102
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
7. Perform test drive to check gear shift feeling in accordance with
instructions displayed.
8. Touch “YES” or “NO”.
9. CONSULT-II procedure ended.

If “NG” appears on the scene, a malfunction may exist.
Go to “Diagnostic Procedure”.
Display Items List
*: Do not use, but displayed.
SCIA5163E
SCIA5162E
DTC work support item Description Check item
I/C SOL FUNCTN CHECK* — —
FR/B SOL FUNCTN CHECK* — —
D/C SOL FUNCTN CHECK* — —
HLR/C SOL FUNCTN CHECK* — —
LC/B SOL FUNCTN CHECK* — —
TCC SOL FUNCTN CHECKFollowing items for “TCC solenoid function (lock-up) ” can be con-
firmed.

Self-diagnosis status (whether the diagnosis is being performed
or not)

Self-diagnosis result (OK or NG)

TCC solenoid valve

Hydraulic control circuit