2004 INFINITI FX35 ignition

QUICK REFERENCE CHART FX35/FX45
QUICK REFERENCE CHART FX35/FX45PFP:00000
ENGINE TUNE-UP DATA (VQ35DE)ELS0003W
Engine modelVQ35DE
Firing order1-2-3-4-5-6
Idle speed
A/T (In “P” or “N” position)rpm
650±50
Ignition timing (BTDC at idle speed)
A/T (In “P” or “N” position)15°± 5°
CO% at idle 0.7 - 9.9 % and engine runs smoothly
Drive BeltDeflection adjustment Unit: mm (in) Tension adjustment Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
Limit After adjustment Limit After adjustment
Alternator and power
steering oil pump7 (0.28)4 - 5
(0.16 - 0.20)3.5 - 4.5
(0.138 - 0.177)294 (30, 66)730 - 818
(74.5 - 83.5,
164 - 184)838 - 926
(85.5 - 94.5,
188 - 208)
Air conditioner com-
pressor belt12 (0.47)9 - 10
(0.35 - 0.39)8 - 9
(0.31 - 0.35)196 (20, 44)348 - 436
(35.5 - 44.5,
78 - 98)470 - 559
( 4 8 - 5 7 ,
106 - 126)
Applied pushing force 98N (10kg, 22lb) —
Radiater cap relief pressure
kPa (kg/cm
2 , psi)
Standard 78 - 98 (0.8 - 1.0, 11 - 14)
Limit 59 (0.6, 9)
Cooling system leakage testing pres-
surekPa (kg/cm
2 , psi)157(1.6, 23)
Compression pressure
kPa (kg/cm
2 , psi)/rpm
Standard 1,275 (13.0, 185) /300
Minimum 981 (10.0, 142)/300
Spark plug Standard type PLFR5A - 11
Hot type PLFR4A - 11
Cold type PLFR6A - 11
2004

QUICK REFERENCE CHART FX35/FX45
ENGINE TUNE-UP DATA (VK45DE)
FRONT WHEEL ALIGNMENT (Unladen* )
ELS0003X
* : Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.Engine modelVK45DE
Firing order1-8-7-3-6-5-4-2
Idle speed
A/T (In “P” or “N” position) rpm650±50
Ignition timing
(BTDC at idle speed)12°±5°
CO% at idle 0.7 - 9.9 % and engine runs smoothly
Tensions of drive belts Auto adjustment by auto tensioner
Radiater cap relief pressure
kPa (kg/cm
2 , psi)
Standard 78 - 98 (0.8 - 1.0 , 11 - 14 )
Limit 59 (0.6, 9)
Cooling system leakage testing pressure
157(1.6, 23)
kPa (kg/cm
2 , psi)
Compression pressure
kPa (kg/cm
2 , psi)/rpm
Standard 1,320 (13.5, 191) /300
Minimum 1,130 (11.5, 164)/300
Spark plug Standard type PLFR5A - 11
Hot type PLFR4A - 11
Cold type PLFR6A - 11
Camber Degree minute (Decimal degree) Minimum – 1° 29′ ( – 1.48° )
Nominal – 0° 44′ ( – 0.73° )
Maximum 0° 01′ ( 0.02° )
Left and right difference 45′ ( 0.75° ) or less
Caster Degree minute (Decimal degree) Minimum 3° 02′ ( 3.03° )
Nominal 3° 47′ ( 3.78° )
Maximum 4° 32′ ( 4.53° )
Left and right difference 45′ ( 0.75° ) or less
Kingpin inclination Degree minute (Decimal degree) Minimum 12° 20′ ( 12.33° )
Nominal 13° 05′ ( 13.08° )
Maximum 13 50′ ( 13.83° )
Total toe-in Distance (A – B) Minimum 0.6 mm ( 0.024 in )
Nominal 1.6 mm ( 0.063 in )
Maximum 2.6 mm ( 0.102 in )
Angle (left plus right)
Degree minute (Degree)Minimum –
Nominal 6′ ( 0.1° )
Maximum –
Wheel turning angle (Full turn) Inside MInimum 32° 00′ ( 32.0° )
Degree minute (Decimal degree) Nominal 35° 00′ ( 35.0° )
Maximum 36° 00′ ( 36.0° )
Outside
Nominal 30° 00′ ( 30.0° )
Degree minute (Decimal degree)
2004

ACS-14
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2004 November 2004 FX35/FX45
5. Pivot the edge of the target board 20° to either side.
NOTE:
Approx. 50 mm (1.97 in) shift rates the 20° movement.
6. Do not place anything in the space shown in the figure (view from top).
NOTE:
In case the space shown in the illustration is not available, make space by covering the side of the target
board with a 400 mm (15.75 in)-size frosted black board or black cloth.
Aiming AdjustmentAKS006YM
CAUTION:

Complete all necessary work for laser beam adjustment until the adjustment completes as shown
in the procedure. If the procedure does not complete, the ICC system is inoperable.

If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Turn ignition switch OFF.
2. Connect CONSULT-II and CONSULT-II CONVERTER on the
data link connector.
PKIA2589E
SKIA5976E
SKIA1216E
PBIB1503E

TERMINALS AND REFERENCE VALUE
ACS-27
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
TERMINALS AND REFERENCE VALUEPFP:00000
Terminals and Reference Value for ICC UnitAKS006YQ
terminals
(wire color)
itemcondition
voltage (V)
+-ignition
switchoperation
1 (R/W)
2 (R/W)
GroundBattery power supply OFF —Power supply voltage
(Approx. 12)
5 (R) CAN L ON — —
6 (GY/L)Release switch power sup-
plyON — Approx. 10
7 (GY/R) NEUT-SW — — —
8 (Y/G)24
(Y/R)Brake pressure sensor
power supplyON — Approx. 5
10 (B/R)
GroundBrake booster solenoid
(+) sideON —
12 (L/W)Brake booster solenoid
(–) sideON —
14 (L) CAN H ON — —
15
(LG/R)Brake release switch
(normal closed)ONDepress the brake pedal. Approx. 0
Release the brake pedal. Approx. 10
17 (BR)24
(Y/R)Brake pressure sensor sig-
nalONRelease the brake pedal. Approx. 0.5
Depress the brake pedal.Approx. 0.5 - 5
(Note) Voltage becomes higher
depending on effectiveness of
depressing brakes.
19 (B)
20 (B)
46 (B)
GroundGround ON — Approx. 0
22 (G/Y)Brake release switch
(normally open)ONDepress the brake pedal. Approx. 10
Release the brake pedal. Approx. 0
29 (SB)ICC brake switch
(normal closed)ONSelector
lever: Not in
“N” or “P”
positionDepress the brake
pedal.Approx. 0
Release the brake
pedal.Power supply voltage
(Approx. 12)
30 (Y) DDL-TX — — —
SKIA1243E
SKIA1243E

ACS-28
[ICC]
TERMINALS AND REFERENCE VALUE
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for ICC SensorAKS006YR
33 (G/R)
42 (G/R)
GroundIgnition switch ON or
STARTON — Battery voltage (Approx.12)
38 (P/G)Stop lamp switch
(normally open) ONDepress the brake pedal. Battery voltage (Approx.12)
Release the brake pedal. Approx. 0
39
(G/OR)DDL-RX — — —
40
(PU/W)parking brake signal ONParking brake is ONPower supply voltage
(Approx. 12)
Parking brake is OFF Approx. 0
47 (W/R)Stop lamp drive output sig-
nalONBrake operating with ICC system Battery voltage (Approx.12)
Brake not operating with ICC sys-
temApprox. 0 terminals
(wire color)
itemcondition
voltage (V)
+-ignition
switchoperation
terminals
(wire color)
itemcondition
voltage (V)
+–ignition
switchoperation
1 (Y)
GroundICC sensor power ON — Battery voltage (Approx.12)
3 (L) CAN H ON — —
6 (R) CAN L ON — —
4 (B) Ground ON — Approx. 0

ACS-30
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
CONSULT-II FunctionAKS006YU
DESCRIPTION
CONSULT-II executes following functions by combining data reception and command transmission via com-
munication line from ICC unit.
CONSULT-II INSPECTION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Turn ignition switch OFF.
2. Connect “CONSULT-II” and “CONSULT-II CONVERTER” to
data link connector, which is located under LH dash panel near
the hood opener handle.
3. Turn ignition switch ON.
4. Touch “START (NISSAN BASED VHCL)”.
5. Touch “ICC” on the selection screen.
If “ICC” is not indicated, go to GI-40, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
Test mode Function
WORK SUPPORT

Monitors aiming direction to facilitate laser beam aiming operation.

Indicates causes of automatic cancellation of the ICC system.
SELF-DIAGNOSTIC RESULTS Displays malfunctioning system memorized in ICC unit.
DATA MONITOR Displays real-time input/output data of ICC unit.
CAN DIAG SUPPORT MNTR The results of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Enables operation check of electrical loads by sending driving signal to them.
ECU PART NUMBER Displays part number of ICC unit.
PBIB1503E
SKIA3098E
SKIA6193E

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-35
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
METER LAMP

Start engine.

Touch “ON” and “OFF” to check that ICC system display oper-
ates as in the following chart.
STOP LAMP

Touch “ON” and “OFF” to check that stop lamp operates as in
the following chart.
BOOSTER SOL/V 3

Touch any of “MODE 1”, “MODE 2”, “MODE 3” to check that fol-
lowing operation condition is caused by operating monitor and
brake pedal.

“START” is displayed 10 seconds after operation start. (Active
test is completed.)
Self-Diagnostic FunctionAKS006YV
WITH CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop vehicle, turn ignition switch OFF, then connect CONSULT-II and CONSULT-II CONVERTER to data
link connector.
3. With engine started, touch “START”, “ICC”, “SELF-DIAG RESULTS” on CONSULT-II screen in this order.
METER LAMP ON OFF
ICC system display Full illumination OFF
SKIA1231E
STP LMP DRIVE ON OFF
Stop lamp Lamp ON Lamp OFF
SKIA1232E
SKIA1233E
PKIA0363J

ACS-36
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
CAUTION:
If “ICC” cannot be shown after several attempts, the ICC unit may have had malfunction. Repair or
replace it. Refer to GI-40, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Self-diagnostic result appears on screen. If “NO DTC ···” is shown, check ICC warning lamp. If any mal-
function is indicated, GO TO step 5.
5. According to ACS-40, "
Diagnostic Trouble Code (DTC) Chart" , perform appropriate check, and repair or
replace malfunctioning part as necessary.
6. Turn ignition switch OFF.
7. Start engine and touch “START”, “ICC”, “SELF-DIAG RESULT”, and “ERASE” on CONSULT-II display in
turn to erase the memory.
CAUTION:
If the memory does not erase, go to 5.
8. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning
lamp does not illuminate.
WITHOUT CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop the vehicle to start the self-diagnosis.
3. Turn ignition switch OFF.
4. Turn ignition switch ON, and within 5 to 10 seconds, press
ACCEL/RES switch 5 times. Then press COAST/SET switch 5
times to start self-diagnosis.
CAUTION:

Do not start the engine.

Do not turn the ON/OFF switch ON.

When operation above is not completed within 5 to 10 sec-
onds, start again from above go to 3.

If self-diagnosis mode cannot be started after several
attempts, the ICC unit may have had malfunction. Repair or
replace it. Refer to ACS-37, "
SELF-DIAGNOSIS BY ICC SYS-
TEM DISPLAY WILL NOT RUN." .
5. When self-diagnosis mode is started, DTC are shown on set vehicle speed indicator.
CAUTION:

DTC will disappear after 5 minutes.
SKIA7067E
SKIA1236E