2004 DACIA SUPERNOVA dashboard

HEATING
61
61 - 1
DISMOUNTING
Disconnect the battery.
Dismount
the documents compartment.
Di smount the attachment c lip of the mixing flow flap control cable, (8) (from the c limate
control unit). Remove the right aeration grill (from the right side of the central console).
Dismount the attachment clip of the distribution flow flap control cable, (7)(from the climate
control unit). Dismount the attachment metal screws (5 ) of the climate control assembly (6 ) on the central
console of the dashboard. Remove the climate control assembly from its seat.
Disconnect the connection box of the climate control switch.
Disconnect the connection box of the instrument panel lighting.
Dismo unt the attachment clip of the recycling flow flap control cable (9) and remove it from its seat.
Remove: the mixing flow flap control cable (8 ) from the heating control button (2 ) and the
distribution flow flap control cable (7) from the distribution control button (3), by releasing the
clips attachment screws.
Remove the climate control switch (4) out of its seat by detaching from clips.
Dismount the four lighting bulbs.
REMOUNTING
Pe rform in the reverse order the dismounting operations, taking into account the following
recommendations: - the flow flaps c ontrol cables are first fixed to the board with the jacket, in axial contact
with the limiting support and then pass the panel button and the similar flow flap on the
corresponding position, then clamp the cable to the unit support; - check if the levers from the climate unit and from the distribution box, have the adequate
strokes t o ensure the close-opening of the flow flaps; - if yes, mount the assembly (6 ) on the central console, the documents compartment and
the aeration grill ;
- if not, set the sleeve l ength of each control cable to the mounting bracket of the climate
unit and the distribution box.
- the maximum moment for the full flow flaps opening is 1,9 Nm.
CLI
MATE CONTROL ASSEMBLY
9
8
7
6
1
2
3
4
5
vnx.su

HEATING
61
61 - 4
DISMOUNTING
Release
the climate maintenance assembly from under the dashboard, dismounting beforehand
the central console, the documents compartment, the lower casing, the dashboard. Unscrew the attachment screws of the turbine deflector.
Unscrew the attachment screws of the blower.
Disconnect the blower from the blower wiring.
REMOUNTING
Perform in the reverse order the dismounting operations.
C
LIMATE CONTROL BLOWER
vnx.su

AIR CONDITIONING
62
62 - 12
CL
IMA TE CONTROL UNIT REPLACEMENT
DISMOUNTING
Disconnect the battery.
Release t he lateral and central console.
Disconnect the wires from the dashboard wiring.
Disconnect the distribution flow flap control cables and the mixing flow flap from the control
lever and the recycling flow flap cable from the climate control panel.
Disconnect the air flow pipes.
Dismount the screws from the front side of the climate box.
Dismount the nuts from the welded screws in the backside of the climate box.
Release the climate control unit.
Replace the climate control unit.
REMOUNTING
Perform in the reverse order the dismounting operations.
CL
IMA TE CONTROL UNIT
AIR INLET ASSEMBLY REPLACEMENT
DISMOUNTING
Dismount the sealing gaskets on the climate box outliner.
Dismount the climate box locking plate.
Dismount the nuts from the right side of the climate box.
Release the air inlet assembly .
Replace the assembly .
REMOUNTING
Perform in the reverse order the dismounting operations.
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 3
BATTERY
DISMOUNTING- REMOUNTING
DISMOUNTING
Af ter identification and elimination of the real cause of the battery discharging, proceed as
follows:
Remove the plastic protector from the plus plug of the battery.
Dismount the attachment nut of the ground wiring from the minus plug of the battery.
Dismount the attachment nut of the wiring from the plus plug of the battery.
Dismount the battery attachment clamp screw.
Carefully take off the battery.
REMOUNTING
Perform the dismounting operations in the reverse order. After that, reset the radio by introducing
the radio code (if the vehicle is equipped with radio) and adjust the dashboard clock. BATTERY
vnx.su

REAR AND INTERIOR LIGHTING
81COCKPIT FUSE BOX81 - 6
DISMOUNTING
Disconnect the (-) plug of the battery.
Turning the button
(4) open, then carefully remove the access little door (1) to the fuse box,
placed under left side dashboard. Dismount the attaching screws (2) of the fuse box on back of the little door.
Rotate the fuse box in order to have access at the connectors of its back then carefully discon-
nect the wiring connectors. If it is necessary the replacement of the module (3 ) attached on the
fuse box, for the fuses F11 – F16, first note the position of the wires connected to these fuses,
then perform the wires disconnecting .
Remove the fuse box.
REMOUNTING
Connect the wiring connectors to the fuse box printed circuit. Observe the form correspon-
dence of each connector with its drawing, marked on the printed circuit of the fuse box. Connect the wires corresponding to the fuses F11 – F16, if those have been previously disconnected.
Position the wires appointed for the fuses F11- F16 and the module (3) of those fuses, then
attach the fuse box on the back of the access little door (1).
Carefully mount the fuse box access little door, then close it.
Connect the (-) battery plug.
Perform functional tests, noticing the correct operation of all consumers supplied by means of
the cockpit fuse box.
OBSERVAT ION
For vehicle equipped with radio-tape player, after battery reconnecting, the radio
code must be introduced, in order to make it again running.
1
4
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 1
This type of anti starting syste m is based on the key recognition, which has a special construction.
It may be separated in two elements which can be identified in the following way (pict.1): the key
he ad (pos.A.) made of plastic, which can be dismounted and the metal insertion (pos.B.), which is
fixed an d ensured by clipping in the key head.
In the key head, there is a coded independent electronic circuit, which is functioning without
battery. When setting the contact on, the anti starting bushing, placed around the starting contact,
is enquiring and catching the coded signal emitted by the key head, then sends it to the Electronic
Control Unit (E.C.U.) decoder. This one is attached on the front left pillar, under the lower casing
of the dashboard and has the function of receiving the code sent from the bushing. If the decoder
recognises the key code then it will send a coded signal to the injection computer, which compares
it with the previous memorised code and will authorise or not the start of the engine.
We mention that the system with radio frequency remote control (RF) of the doors blocking
/unlocking, has no influence to the anti starting system. In this case, the key head has a different
construction, having an activation button of the remote control and a red LED, which is lighted in
the moment of blocking/unlocking the doors, by pushing the key button. Inside the key head
there is the coded electronic circuit for the anti starting system and an imprinted electronic circuit,
s upplied by a battery, for t he RF remote control operation of blocking/unlocking the ve hicle
doors.
The anti starting system is activated after approximate 10 seconds from the breaking of the
contact and is visualised by the blinking of the anti starting indicator placed on the instrument
panel.
If the battery is low charged, the t ension drop on the starter, at starting,
may cause the activation of the anti starting system and the start of the engine is
impossible.
pict.1
GENERALITIES
AT T ENTION
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 16
D. SIMPLE S
YNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations:
- the RF remote control c ode is no longer i n the range of the E.C.U. decoder re ception,
because of consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E.C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.)
The following operations will be performed: - take off t he contact
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/o pening course.
- the procedure of synchronisation is finished; check the blocking/ unlocking by pushing
the RF remote control.
OBSERVAT ION
Duri ng those 10 seconds you can visualise by means of the CLIP tester the state 17G
“THE PROGRAMMING IN PROGRESS OR THE TIR/TRF
RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E .C.U. decoder
and will be performed as follows:
- connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket) of
the vehicle. - select the vehicle type “SUPERNOVA” and the “050” equipping level;
- select the m enu “ COMPUTERS TEST” then “ ANTI STARTING”
- enter the m enu “COMMAND MODE” and select “CONFIGURATION”
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice the RF remote control button; the doors will block and then unlock and the
anti starting indicator will t urn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 20
D)
Memorising of the new code of the injection computer
- in ACTUATORS
launch the command MANUAL INTRODUCTION CODE ; type
the repairing code of the old key kit, then validate it with the key
ENTER.
- the message “COMMAND IN PROGRESS ” will be displayed followed by the message
“FINISHED COMMAND ”.
-s et the contact on; t he anti starting LED indicator will start blinking, then take off the
contact;
-set the c ontact on for 10 seconds ; take off the contact;
- check if the engine starts with the two keys.
If the engine doesn’t start, repeat this operation (point D).
E) Key resynchronisation (remote controls)
-if the vehicle is equipped with only one remote control, its resynchronisation will be
performed as follows (simple resynchronisation);
- with t he contact taken off, push continuously on the c entra l l ocking but ton from the
dashboard, up to the moment the anti starting LED indicator remains lighted (the doors actuators
are performing a closing/opening course.) From this moment, t he operator has 10 seconds to
perform the next operation; - push twice on the remote control (the doors actuators are performing a closing/opening
course.) and the anti starting LED indicator turns off; - if the vehicle is equipped with two remotes controls, perform the simple resynchronisatio n
procedure for the first key and a specific resynchronisation procedure for the second key, with
the CLIP tester as follows: - in COMPUTER TEST select ANTISTARTING with t he c ontact t aken off, then
COMMAND MODE , CONFIGURATION ; launch the command PROGRAMMING OF
THE SECOND TIR/TIE KEY and validate (the doors actuators are performing a closing/
opening course.). Then within 10 seconds, push twice on the remote control (the doors actuators
are performing a closing/o pening course).DIAGNOSTIC
vnx.su