2004 DACIA SUPERNOVA wheel

71
INTRENAL BODY TRIM
72 - 1
1. Front door threshold
covering
2. Rear door threshold covering
3. Upper front pillar covering
4. Middle pillar lower covering
5. Middle pillar covering
6. Rear passage covering
7. Rear side panel covering
8. Rear wheel passage covering CARR
IAGE BODY COVERINGS
vnx.su

71
INTRENAL BODY TRIM
72 - 7
DISMOUNTING
Detach from the two attachment clips
(1)
the rear wheel passage covering. Release the rear wheel passage covering.
REMOUNTING
Per f o r m in the reverse order the
dismounting operations. R
EAR WHEEL PASSAGE COVERING
vnx.su

76
REAR SEATS FRAMES AND RU NNERS
76-1
The rear bench is composed of two separated swinging seats, unequal and two separated,
unequal, swinging back rests.
DISMOUNTING
Di smount the seats, by swinging and by removing them from the welded supports on the
carriage body.
For the back rests dismounting perform the following operations: - lift the unlocking buttons (1), and swing out the back rests a head.
- dismount the four screws for the attachment of hinges on the wheels’ passage.
- remove the back rests from the central hinge
REMOUNTING
Perform in the reverse order the dismounting operations.
REAR BENCH
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 3
GENERALITIES
The anti starting bushing (picture 5) is located around the starting contact a nd is accessible
after the dismounting the steering wheel’s cases. It catches the signal from the key head and then
s ends a coded signal t o the E .C.U. decoder.
The vehicles equipped with RF remote control keys for blocking/ unlocking t he doors are
provided with another anti starting bushing which transmits to the E.C.U. decoder also the signal
received from the RF remote control.
The recognition of the two types of decoding bushings is realised by means of codes labelled
on their body, as follows :
- code 042264J - for vehicles w ithout RF remote control
- code 8200044257 - for vehicles with RF remote control
The E.C.U. decoder (picture 6) has the
following functions :
- decode the signal received from the anti
starting bushing ;
- sends a c ode to the injection computer
in order to authorise the engine starting.
- controls the anti starting indicator of the
instrument panel - receives the coded signal from the anti
NOTE
In case both keys we re lost, the code of the key head (8 characters) and the code of
the m etal insertion (4 characters) can be red from the vehicle invoice. If al so the i nvoice
was lost, the two mentioned codes can be found out based on the chassis series number
of that vehicle, accessing the database of the DACIA manufacturer, calling the TECH
LINE.
pict.5
pict.6
starting bearings, for the vehicles equipped with RF remote control;
- commands the blocking/unlocking of the doors, if the vehicle is provided with RF remote
control keys;
- commands the dome ceiling lighting, for the vehicles equipped with this system.
E.C.U. DECODER
ANTI STARTING BUSHING
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 8
If further to the diagnostic, it is established
the necessity of the replacement of the anti starting
bushing, proceed as follows: -dismount the attachment screws of the steering wheel casing ;
- unlock the steering wheel and bring it in low position;
-r emove the steering wheel upper casing;
- disconnect the anti starting bushing connector from the front wiring;
-r emove the bushing;
- mount the new bushing outside the starting contact (anti theft) system;
- connect the bushing connector to the front wiring;
- mount the steering wheel casing;
- check the operation of the indicator and the anti starting system when the contact is off,
then with the contact on and the engine started. ANTI STARTING BUSHING REPLACEMENT
vnx.su

83
INSTRUMENT PANEL
DISMOUNTING
Disconnecting battery.
Dismounting flexible shaft( speedometer cable) from the gearbox.
Dismounting control cable from the recyclin g flap.
Dismounting steering wheel and the steering wheel casing.
Dismountin g dashboard lower fairing.
Dismountin g documents compartment.
Disconnect documents compartment lamp.
Dismountin g central console.
Dismounting flaps control cables from the climate control unit.
Discon necting: cigarette lighter, climate control lighting, ashtray lighting, climate control switch .
Dismounting headlamps adjustment control from the dashboard.
Dismounting dashboard from the windscreen lower cross bar.
Disconnecting flexible shaft (speedometer cable) from the instrument panel.
Disconnecting air conducting ducts to aerators.
Disconnecting front wiring from the instrument panel and from the dashboard wiring.
Dismounting instrument panel attachmen t clamps from the dashboard.
Dismountin g clamps from the instrument panel.
Mounting clamps on the new instrument panel.
Mounting instrument panel with clamps on dashboard.
Connecting flexible shaft to the instrument panel.
Connecting front wiring to the instrument panel and to the dashboard wiring.
Positioning and fixing air conducting ducts.
IN
STRUMENT PANEL REPLACEMENT
83-5
vnx.su

83
INSTRUMENT PANEL
Positioning and fixing flaps control cables to the climate control unit.
Connecting dashboard wirin g to: cigarette lighter, climate contro l lighting, climate control switch,
ashtray lighting.
Connecting documents compartment lamp.
Mounting documents compartment.
Mounting central console.
Mounting dashboard lower fairing.
Mounting steering wheel casing and steering wheel.
Mounting flexible shaft to the gearbox.
Mounting control cable to the recycling flap.
Connecting battery.
Functional tests.
REMOUNTING
Perform the dismounting operations in the reverse order.
83-6
IN
STRUMENT PANEL REPLACEMENT
vnx.su

84
CONTROLS - SIGNALLING
84 -1
(STARTING – IGNITION SWITCH)
The anti theft mechanism is placed on the right part of the steering column and has the purpose
to starter control when electric system is connected, being provided in the same time also with a
steering locking device, with anti theft lock.
NOTE
At the anti theft mechanism there is not any more marked G position (garage) because
it does not allow the taking out of the key in this position but helps in pi n unblocking
for removing the mechanism from the steering column.
Disconnect the battery.
Dismount the steering wheel casings.
Disconnect the anti-starting bushing.
Remove the bushing off the steering column.
Disconnect the switch connection wires.
B ring the key in the interme diary position (ex G).
Dismount the attachment screw (1).
P ush the mobile pin ( 2) and pull backwards
the switch.
REMOUNTING
Mount the switch in its place.
Tighten the attachment screw(1).
Connect :
- the switch
- the battery.
Position and mount the anti-star ting bushing.
Connect the anti-starting bushing to the ve-
h icle wirin g.
Check the switch operation.
Mount the steering wheel casings. DISMOUNTING
ANTI THEFT MECHANISM
vnx.su