2004 DACIA SOLENZA width

VA LUES AND ADJUSTMENTS
07
07 - 1
Dimensions
Dimensions (mm)
Total length: 4083
T otal width:G = 1664
Total height:
* emptyH = 1379
*
loaded (authorized maximum total weight)1329
Wheel base* emptyA =2476
*
loaded2479
Front wheel track width, ground level measurement:
* empty E = 1429
* loaded1428
Rear wheel track width, ground level measurement F = 1348
Gr ound clearance (K)
*
empty-
*
loaded120
vnx.su

VA LUES AND ADJUSTMENTS
07
07 - 6
Brakes
Veh icl e
Normal
20 Minim
19 Normal
228 Minim
229 Front
0.04 Rear
-
Brake disk width and drums diameter (mm) Front Rear Maxi
m disk
axia l run out
Veh icl e
Normal
14 Minim
7 Normal
5 Minim
0.5 mm
above the
rivets SAE J 1703
DOT 4
Gaskets thickness (mm)
Front Rear Bra ke fluid
SOLENZ A
SOLENZ A
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 14
VA LVES SEATS
Sealing face angle
(α )
- intake 1200
- exhaust 900
Sealing face width (x)
- intake 1.7 ± 0.1mm
- exhaust 1.7 ± 0.1mm
External diameter (D)
- intake 38.5 mm
- exhaust 34.5 mm
VA LVES GUIDES
The valves for both intake and exhaust are provided with oil-rings, that must be replaced at
each valves dismounting.
Chara cteristics
Internal d iameter 7 mm
External diameter 12 mm
Position as against the spring seating on
cylinder head: - intake ( A) 12.34 mm
- exhaust ( E) 12.34 mm
Tilt as against vertical (ββββ
)1 7
0
vnx.su

GENERAL
30 - 6
30Composition and dimensions of the main
braking system elements
Front brakes
- brake caliper bore diameter → 54 mm
- brake disk diameter → 235 mm
- disk axial runout measured at → 215 0. 04 mm
- brake disk maximal thickness 20 mm
- brake disk minimal thickness 19 mm
- braking pad thickness (support included) 14 mm
- brake pad minimal thickness (support included) 7 mm
Rear brakes
- wheel braking cylinder bore diameter → 22 mm
- new drum diameter → 228 mm
- drum diameter after grinding → 229 mm
- braking shoes lining width 40 mm
- braking shoes lining thickness 5 mm
- minimal accepted braking lining height above rivets 0.5 mm
Master cylinder
- diameter of bore 20.6 mm
Brake fluid reservoir without alarm sensor
Pressure limiter for circuit in parallel
S ervobrake master vac 7" 177.8 mm
vnx.su

GENERAL
30 - 11
30Braking system diagnostic
II. CONSTANT EFFECT AT BEHAVIOUR
EFFECTS
Brakes not accomplishing the required
b raking distance
Vibrating brakes
When braking, the vehicle ( front part)
is left/right deviating
Braking
Heating brakes POSSIBLE CAUSES
- Non-uniform worn brake linings (backing
off);
- Brake l inings slightly gr eased;
- Springs with modified characteristics.
- Brake disks with high wobbling;
- Inconstancy brake disks width;
- Particles abnormal deposit on brake disks
(oxidation between linings and disk).
- Front axle suspension, steering (to be
checked);
- Stuck piston;
- Tires – wear, inflation pressure;
- R igid duct narrowed (flattening).
- Stuck piston;
Automatic adjustment : hand brake cable very
tighten.
REMARK :
Automatic recovering is performed by
means of the brake pedal, if there is no ab-
no rm al t ensi on in the hand brake cable
when released (hand brake released).
- Return spring.
- Insufficient hydraulic stroke of the brake
pump, not allowing the return at rest of the
brake pump pistons ( brake pump remaining
under pressure);
- St uck pistons or hardly returning;
- R igid duct narrowed (flattening);
- Def ective adjustment of the hand brake
control.
vnx.su

35
WHEELS AND TIRES
35 - 1
Characteristics
WHEELS
The wheels identification marking is repre sented in two ways: -engraved marking for steel rims
- cast marking for aluminum rims
The marking enables acknowledgment of the main wheels dimensions criteria.
This marki ng may be:
- Complete Example : 5.5 J 14 4 CH 43 , or
- Simplified
Example: 5.5 J 14
The wheel attachment holes are situated on a diameter of 100 mm.
Maximum axial runout : to be measured in points P1 and P2.
Maximum radial runout : to be measured in points G1 and G2.
AB C D E F
Rim width Rim Rim nominal Number of Tire Offset
Rim type ( in inches) edge diameter attachment staffing ( in mm) profile (in inches) points profile
5.5 J 14 4CH 43 5.5 J 14 4 CH 43
5.5 B 13 4CH 46 5.5 B 13 4 CH 46
G1
P1P2
G2
vnx.su

WHEELS AND TIRES
35
35 - 2
TIRES
Identification marking examples: 165 / 65 R 14 79 T 165 65 R 4 79 T
1
24563
1
2
6
5
4
3
Characteristics
- 165 - Tire width in mm (1)
- 65 - h / l height / width ra tio, percentage;
- R - Radial structure
- 14 - Inner diameter in inches ( →); this is corresponding with the rim diameter
– 79 – Charging index
– T – Speed index max. 190 km/ h
vnx.su