2004 DACIA SOLENZA ABS

IGNITION AND INJECTION
17
17 - 65
Diagnostic – Conformity checking
Sequence Function Parameter/Controlled s tate or action Visualization Diagnostic
and Observations
In case of a problem
10 Anti-detonationPR013 : Detonation average signal 20 < X < 1 00 consult the
circuit PR0013 diagnostic
ET037 : Enriching adjustment ACTIV E
11 Enriching In case of a problem
adjustment PR009 : Upstream O2 sensor voltage 20 < X <84 0 mV consult the
ET037 diagnostic
PR 035 : Enriching correction value 0 < X < 255 Average value 128
Cl imate contro ET009 : Climate control request ACTIV E
(controlled AC) If injection is authorizing thecompressorcoupling
ET070 : Climate control compressor ACTIV E
If injection is
authorizing the compressorcoupling
In case of a problem
consult the ET00,
ET070 and DF1 18
According to E035 : fan low speed ACTIV Ediagnostic or chapter
conditions and Fan must “Injection/CA
requests of the run at low str a tegy” injection speed
computer,
12 w a t e r temperature,
electric If state
consumption, ET038 : accelerated idling ACTIV E
refrigerant fluidThen parameter pressure PR006 : Engine regime 850 < X < 960 rpm
If type Info PA 300 complete or coldP R044 : Absorbed power by AC ( X<300W if the
l oop present in compressor injection is not
injection authorizing the
the compressor
coupling)
If type cold PR027 : Refrigerant fluid pressure
l oop in injection 2< X < 6 bar
RECOMMEND
AT IONS The values show n on this conformity checking are only as indication.
Performing conditions : Warm engine at idling and no consumers.
vnx.su

IGNITION AND INJECTION
17
17 - 69
Diagnostic – States interpretation
ET009CLIMATE CONTROL REQUEST
RECOMMEND AT IONS No failure must be prese nt or memorized.
The injection computer is not noticing the air conditioning starting control.
Ch eck the in sulation and continuity on the line from pin 23 (climate contr ol of type Info Power
Absorbed by compressor) or from pin 46 (climate control of type Logical connection) of the injection
computer.
M end if necessary.
If the proble m is persisting consult the climate control diagnostic.
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 70
ET035LOW SPEED ENGINE FAN
RECOMMEND AT IONS No failure on the water temperature sensor circuit must be present in
order to perform this diagnostic.
Check:
- engine fan condition
- engine fan resistance condition
- condition f the engine fan mass connection
-l ow speed engine fan supply
-s upply line between engine fan and engine fan relay
M end if necessary.
C heck the connection and condition of the connector of the low speed engine fan relay
Re place the connector if necessary.
Rem ove the rela y of the low spe ed engine fan
C heck, with the contact set on, the supply presence +12 volts at pole 1 of the rela y.
M end if necessary.
Measure the relay coil resistance.
Re place the rela y of the low spe ed engine fan, if necessary.
Connect the 90 ways terminal box instead of the computer and check the in su la t i on, continuity and
absence of the parasite resistance on the connection between: Pin 8 injection computer > Relay of the low speed engine fan
M end if necessary.
Diagnostic – States interpretation
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 71
ET036HIGH SPEED - ENGINE FAN
RECOMMEND AT IONS No failure on the water temperature sensor circuit must be present in
order to perform this diagnostic
Check:
- engine fan condition
- engine fan resistance condition
- condition of the engine fan mass connection
-hi gh speed engine fan supply
-s upply line between engine fan and engine fan relay
M end if necessary.
C heck the connection and condition of the connector of the hi gh speed engine fan relay
R eplace the connector if necessary.
Rem ove the relay of the high speed engine fan
C heck, with the contact set on, the supply presence +12 volts at pole 1 of the rela y.
M end if necessary.
Measure the relay coil resistance.
R eplace the relay of the high- speed engine fan, if necessa ry.
C onnect the 90 ways terminal box instead of the computer and check t he in su la t ion, continuity and
absence of the parasite resistance on the connection between: Pin 38 injection computer > Relay of the high speed engine fan
M end if necessary.
Diagnostic – States interpretation
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 75
PR001 MANIFOLD PRESSURE
RECOMMEND AT IONS No failure must be prese nt or memorized.
Incoherent manifold Check the insu lation, continuity and the absence of the parasite
pressure, contact on resistance of the connections between:
Pin 15 injection computer > p in A pressure transducer
Manifold pressure < Pin 16 injection computer > pin B pressure transducer
mini mal pressure at Pin 78 injection computer > p in C pressure transducer
idling Mend if necessary.
Incohe rent
atmospheric If all checked elements are correct, replace the transduc er. pre ssure
(PR0 16 )
M anifold pressure > Check :
m aximal pressure - Sealing between manifold and transduc er.
at idling - Valves clearance. -Canister purging valve operation
-Cyli nders compression
-La ck of leaking at inlet manifold (“false air”)
- Exhaust is not clogged.
If all these elements are correct, replace the tr ansducer.
Diagnostic – Parameters interpretation
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 76
PR002WATER TEMPERATURE
RECOMMEND AT IONS No failure must be prese nt or memorized.
If the value red is incoherent, check that sensor is correctly following the standard curve “resistance
s ubject to temperature”.
R eplace the sensor if this is prese nting deviations (Observation: the presence of the deviations from
normal values of a sensor are ofte n due furthe r to an electric shoc k).
C heck the insulation, continuity and the abse nce of the parasite resistance of the con nections
between:
Pin 13 injection computer > pin B2 water temp erature sensor
Pin 73 injection computer > pin B1 water temperature se nsor
Me nd if necessary.
Diagnostic – Parameters interpretation
AFTER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 77
ET003AIR TEMPERATURE
RECOMMEND AT IONS No failure must be prese nt or memorized.
If the value red is incoherent, check that se nsor is correctly following the sta ndard curve
“resistance subject to temperature”.
R eplace the sensor if this is presenting deviations (Observation: the prese nce of the deviations
from normal values of a sensor are ofte n due further to an ele ctric shock).
Ch eck the insulation, continuity and the absence of the parasite resistance of the connections
between:
Pin 49 injection computer > pin 1 air tem perature sensor
Pin 77 injection computer > pin 2 air temperature se nsor.
M end if necessary.
Diagnostic – Parameters interpretation
AF TER Restart the conformity checking from the beginning.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 79
Diagnostic – Parameters interpretation
PR017VALVE POSITION
RECOMMEND AT IONS No failure must be prese nt or memorized.
Limit memorizing of Check that potentiometer me chanical limitter has not been
PR008 or non-dete ction Check the acceleration control (fric tion, pedal ET005 obstacle,…).
of the released
acceleration pedal
ET003 or non-detecting Check the valve potentiometer resistance.
of pressed Replace the valve potentiometer, if neces sary.
acceleration modified. Check the insulation, continuity and the absence of the p arasite
resistance of the connection between:
Pin 43 injection computer > pin C valve potentiometer
Pin 74 injection computer > pin B valve potentiometer
Pin 75 injection computer > pin A valve pote ntiometer
The valv e pos ition Check that potentiometer is mec hanic ally coupled to the valve.
is fixed (PR017) If necessary, replace the transducer.
AFTER Restart the conformity checking from the beginning.
REPARATION
vnx.su