2004 DACIA SOLENZA fuse box

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 6
All new decoders, are not coded. After mounting on the vehicle, it is necessary the memorisation
of the key head code by the decoder in order to be operational. If only the decoder is replaced, no
intervention is necessary to the injection computer, which will keep the old anti starting code. When
the vehicle is provided with RF remote control for blocking/unlocking the doors, the performing of
the resynchronisation of the keys with the decoder is imposed, after its mounting. If further to the
di ag nostic of the anti starting system, using the CLIP tester, the replacement of the decoder is
imposed, proceed as follows:
DISMOUNTIN G
- disconnect the (-) terminal of the battery;
- d ismount the ECU decoder-relays assembly;
- ro tate the ECU decoder assembly, in order to have access at its rear connectors;
- d isconnect the front wiring connector from the E.C.U. decoder;
- deta ch ECU decoder from clips of the relays-ECU decoder support.
REMOU NT I NG
- attach in clips the new E.C.U. decoder in the support, connect the front wiring connector to
the ECU decoder, then attach the assembly on the driving post cross member in its place and
mo unt its attachment screw;
- remo unt carefully the access flap of the fuse box;
- reconnect the (-) term inal of the battery.
Proceed then to the insertion of the anti starting code using the contact key, then to its me morising
(va lidation) in the E.C.U. decoder, using the CLIP tester. For this purpose, perform the “E.C.U.
decoder replacement procedure and anti starting code memorising”. Check then the correct operation
of the anti starting system with both keys.
ATTENTION!
Once the decoder has memorised the key codes, this code cannot be erased or replaced
with another one.
If it is necessary the replacement of the kit (E.C.U. decoder and two key heads), then the “ Kit
replacement procedure” must be performed.
Dismounting - remounting E.C.U. decoder
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 18
Diag nostic
FA ILURES AND STATES INTERPRETATION
1. FAILURE OF COMMUNICATION CLIP TESTER/ E.C.U. DECODER
RECOMMENDATION Check if the lines K and L are not disturbed by another computer of the vehicle.
Check the condition of fuse F 03 from the cockpit fuse box.
Replace the fuse if necessary.
Check if the CLIP tester is not the cause of the failure; check if the tester is communicating
with another computer of the same vehicle (injection computer).
M easure the tension of the vehicle’s battery (U> 12,3V). If necessary, charge the battery.
Check if the E.C.U. decoder is correctly connected to the vehicle’s wiring.
Check the right supply of the E.C.U. decoder:
-presence of the mass at pin A8 of the E .C.U. decoder
- supply + I.C. at pin A9 of t he E .C.U. decoder
Be sure that the diagnostic socket i s proper supplied, according to the circuit diagram.
Check the continuity and the isolation of the electric wiring on the corresponding pins layout.
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the connection tester CLIP – E.C.U. decoder can’t be established, then replace the decoder.
AFTER REPAIRING After establishing the communication with the tester, fix the
possible failures.
Perform a conformity checking.
{ }
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 22
Diag nostic
5. FAILURE : DEFECTIVE COMMUNICATION ANTI STARTING SYSTEM -
E.C.U. DECODER
RECOMMENDATION -
Check the continuity and the isolation related to the mass and + 12 V voltage of the wiring
between the anti starting system pin 4 pin A2 E.C.U. decoder
Fix it if necessary.
Check the anti starting bushing supply : + 12V to the pin 3 and the mass to pin 2.
Di sconnect the E.C.U. decoder and measure the presence of +12 V at the pin A2 of the
decoder, the contact being taken off. If there it isn’t +12 V, check the fuse condition F03 from
the cockpit fuse box.
If the problem persists, replace the anti starting bushing.
Set the contact on and perform the impulse detection test at the pin A2 of the E.C.U. decoder.
Is there an impulse ?
YES
NO Replace the anti starting bushing.
Replace t he E.C.U. decoder.
Remove the memorised
failures by means of the CLIP tester.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system .
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 26
Diag nostic
FAILURES LOCATING BASED ON CLIENT CLAIM
(algorithm for damage locating)
A LP1. MISSING COMMUNICATION CLIP TESTER / E.C.U DECODER
RECOMMENDATION Check if the lines K a nd L are not perturbed by another computer
of the vehicle.
Check the condition of the F03, F04 fuses from cockpit fuse box.
Be sure the CLIP t ester is not the cause of t he failure, by trying the communication with
another computer of the vehicle.
Check the tension of the battery (U>12,3V). If it is necessary, charge the battery.
Check the correct c onnection of the E.C.U. decoder to the wiring.
Check the supply of the E.C.U. decoder : - mass at pin A8; - supply (+IC) at pin A9.
Be sure that the diagnostic socket is correctly supplied.
Check the continuity and the isolation of the electric wiring on the pins’ line corresponding to:
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the dialogue CLIP tester – E.C.U. decoder cannot be established, then replace the decoder.
When the communication with the tester is established, solve the
AFTER REPAIRING failures displayed by CLIP.
Perform a conformity checking.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 29
Diag nostic
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
( even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHED
OFF
RECOMMENDATION Check if the “Procedure E.C.U. decoder replacement” was correctly performed
Check the fuse F03 condition from the cockpit
fuse box.
Is the fuse good?
Is there the failure “DOORS BLOCKING
CONTACT”.
Check the continuity and the isolation related
to the mass, between the pin A 5 of the E.C.U.
decoder and the dashboard.(pin 6 from black
connector)
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
damaged element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder a nd check if t he indicator switches
off;
- if the anti starting system is turned off, connect
the pin A5 of t he wiring connector from the
E.C.U. decoder to an electric mass and check
if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
No
No
No
Yes
Y e s
No
Yes
Yes
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 33
Diag nostic
ALP7. UNLOCKING DOORS NOT OPERATING BY RF REMOTE CONTROL
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, these must be repaired.
Are the states 11G and 11D be c om ing
A CTIVE when t he RF remote c ontrol is
activated?S ee the treatment of the states 11G
and 11D cf. chapter “Diagnostic”.No
Check the fuse F03 condition from the cockpit
fuse box.
Is it good?
Replace the fuse.No
Ye s
Yes
See the treatment of the failure
“Doors blocking contact” and the state 14 G cf. chapter
“Diagnostic”.
See ALP6.
Yes
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
Activate the doors’ locking switch from the
dashboard.
Are the doors blocking/ unlocking ?
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 34
Diag nostic
ALP 8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester. If there are failures, fix them first.
Check if the synchronisation of the RF remote control and the E.C.U. decoder has been
performed.
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation
related to t he mass and the +12 V of the
electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalling system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F02 condition from the cockpit
fuse box.
Is it good?Replace the fuse.
Di sconnect the FLASH relay. Supply with
+12, the pole 4 of the relay. Are the left turning
lights turning on? Supply with +12 V the pole
5 of the signal relay. Are the right/left turning
lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 54
RECOMMENDATIONS Applying conditions of the diagnostic to the memorized failure:

- fa ilure declared present when setting the contact on (+After contact).
Diagnostic – Failures interpretation
DF 069
PRESENT OR
MEMORIZED UCH CONNECTION ANTI-STARTING BUSHING
CC.O: short-circuit at m ass
CC.1: short-circ uit a t 12 V
CC.0Check the condition and connection f the anti-starting bushing
If necessary, repair the connector.
Check the connection and condition of the connector with 40 pins
EH1 of the Cockpit Central Unit
Repair the connector if necessary.
Disconnect the bushing connector and check the correct supply of
+ 12V at pin 3 bushing connector
Fix it if necessary.
Check the continuity and insulation of the connection between:
Cockpit fuse box F04 (15A) pin 3 bushing
Fix it if necessary.
CC.1Check the connection and condition of the bushing connector.
Fix the connector condition if necessary.
Check the connection and condition of connector 40 pins EH1 of
Cockpit Central Unit.
Fix the connector if necessary.
Check the continuity of the connections between:
mass pin 2 bushing
Connector 40 pi ns EH1 of UCH pin A16 pin 4 bushing
Fix if necessary.
AFTER REPAIRING Apply the recommendation Fix all others failures
Erase the memorized failures.
vnx.su