2004 DACIA SOLENZA engine

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 9
If further to the diagnostic by means of the CLIP tester, it is necessary the replacement of the
E. C.U. (computer) injection, for its dismounting, proceed as follows:
-disconnect the battery (the contact being off);
-d ismount the screw from the battery attachment clip;
-remov e the battery;
-d ismount the two attachment nuts of the injection computer and of the ECU protector;
-remov e the injection ECU protector;
-d isconnect the injection computer from the engine wiring;
-d ismount the ECU injection
For mounting, perform the dismounting operations in the reverse order.
The in jection computer is delivered not coded. It is necessary the memorising of an anti starting
code in the computer, after this has been mounted.
Proceed as follows: 1. Set the contact on, without starting the engine, for 5 seconds.
2. Ta ke off the contact; after 10 seconds, the anti starting function is activated, and the anti
starting indicator will blink rarely (one blink per second). 3. Set the contact on. The anti starting indicator must turn off after 3 seconds and the engine
can be started. In or der to disconnect the injection computer (E.C.U. injection) act upon the blocking lever (A)
of the connector in the direction of the B arrow, then the connector will be lifted in the direction of
the C arrow. In ca se the vehicle is blocked on the road further to serious damages of the anti starting system,
the “ Procedure for repairing code introduction” may be used, which allows the moving of the
vehicle to the nearest DACIA service centre for complete repairing. In order to perform this
procedur e it is necessary the CLIP tester and the specific repairing code of that vehicle.
A
B
C
Electric control unit injection replacement
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 11
REPLACEMENT OF THE ACCOUSTIC WARNING
(for auto made after 03.07.2003)
The ne w acoustic warning i s attached in t he engine c ompartment, on the left upper front
longitudinal girder.
1 2
DISMOUNTIN
G
Disconnect the battery (-) terminal.
Remove by hand the battery screen from the acoustic warnin g attaching area so that dismounting
of the screw ( 1) is permitted.
Di smount the screw ( 1) attaching the acoustic warning on the l eft upper front longitudinal
girder.
Disconnect the acoustic warning connector (2).
Carefully remove the acoustic warning
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Check the operation of the acoustic warning.
REMARK !
Eac h t i me whe n di smount i ng t he ac oust i c warni ng, re pl ac e the fan-t y pe the
attachm ent screw ( 1) .
The required tightening moment of t he attachment screw is of 21 Nm + 10%.
Acoustic warning
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 13
Procedures
1. Return to “COMPUTER TEST”
2. Set the contact on for 2 seconds in “ M” position, without start ing the engine. The anti
starting indicator will begin to blink rapidly.
3. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE ………………………………......…… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….…… PASSIVE
10. Take the c ontact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE LIST”, which now, must be like that: 18G FIRST CYCLE MEMORISING…………………………….....…ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………….……..PASSIVE
19D UNBLOCKED KEY PROGRAMMING …………………..…… PASSIVE
13. Set the contact i n “M” position for 2-3 seconds in order t o send the code t o the E.C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI STARTING” is “ ACTIVE”.
Perform the synchronisation of the TRF remote control with the decoder (with 1or 2 keys).
OBSERVAT ION:
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows:
- take the contact off; wait for 10 seconds, then the anti starting indicator will blink;
- in the menu, “COMMAND MODE” access “ ACTUATORS” then validate “ FORCED
PROTECTION MODE” launching the command from the blue button situated on the ri ght
topside of the screen. “COMMAND IN PROGRESS” will be displayed and then “FINISHED
COMMAND”; - in t he m enu “ STATE LIST” search for the state 10G ”ANTI START ING”, which
must be “ ACTIVE”; - set the contact on “M” position; the anti starting indicator will blink rapidly, and the
engine starting is impossible;
- remove the key from the contact and check then the engine starting with both keys, so
the procedure is finished.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 15
Procedures
7. Set the contact i n “M” position with one of the ke ys (without start ing the engine), for
about 2 seconds and then check the following states, which must be:
9D RECEIVED KEY CODE ……………………………….....…..... ACTIVE
19G NOT PERFORMED KEY PROGRAMMING ………….........… ACTIVE
8. Set the contact with the second key (without starting t he engine) for about 2 seconds.
Check then the following states:
-case (a)- the second key belongs to the vehicle;
9D RECEIVED KEY CODE ……………………………………..… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….....… PASSIVE
- case (b)- t he second key doe s not belong to t he vehicle or the first ke y was used once
again;
9D RECEIVED KEY CODE ……………………………………..… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………….....…… ACTIVE
9. The anti starting indicator blinks rapidly.
10. Take off the contact. In the menu “ COMMAND MODE” select “ACTUATORS” and
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear,
followed by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE L IST”, which now must be as follows: 18G FIRST KEY MEMORISING…………………………….........… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………...……PASSIVE
19D UNBLOCKED KEY PROGRAMMING ………………...…...…PASSIVE
13. In the menu “COMMAND MODE” select “ ACTUATORS”. Select the command “
FORCED PROTECTION MODE” launching the command from the blue button situated on
the ri ght topside of the screen. The display will show “COMMAND IN PROGRESS” and
then “FINISHED COMMAND”.
Return to the “STATE LIST “ and check t he state: 9GFORCED PROTECTION MODE ………………………....…… ACTIVE
14. Set the contact on “M” position. The anti starting indicator will start to blink ra pidly.
Check in the “ STATE LIST” if the state “ANTI STARTING” is “ACTIVE”.
15. In the menu “COMMAND MODE” a ccess “ACTUATORS”, then select the command
“ MANUAL CODE INTRODUCTION”. Type t he four fi gures of the repairi ng code, t hen
validate with the key “ENTER”. On the screen the message “COMMAND IN PROGRESS”
w ill appear and then “FINISHED COMMAND”.
16. Set the contact off and then set again the contact on, without starting the engine, in order
to send the new anti starting code to the injection computer. The anti starting indicator will light
for 3 seconds, and then it will turn off.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 16
Procedures
17. The procedure is finished. Check the engine starting with both keys.
REMARK:
For the RF remote control synchronisation, after the replacement of a kit, take into account
the following situations:
- for the first RF remote control, perform the “ SIMPLE SYNCHRONISED PROCEDURE”;
- for t he second RF re m ote control pe rform the “SPE CIFIC SYNCHRONISE D
PROCEDURE”. C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by means of the CLIP tester. This is possible only
if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed by the
state:
10G ANTI STARTING ……………………………………………….ACTIVE
After getting from DACIA database the repairing code (based on the vehicle chassis series
and on the code from the vehicle’s key head), perform the following operations.
1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle.
2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “B41”;
5. Select the menu “ COMPUTER TEST” then select “ ANTI STARTING”.
6. In the menu “STAT E LIST” find the state 10G “ANTI STARTING” which must be
“ACTIVE”. 7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL CODE INTRODUCTION” where you will write the
repairi ng c ode (form ed of 4 fi gures), then validate it with t he ke y “ ENTER”. The message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”. 9. Now the procedure is finished and you may start the vehicle engine.
AT T E N T I ON!
Yo u may perform three attempts of introducing the repairing code; if after the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then set it
again, then other three attempts may be performed.
REMARK:
This procedure does not decode the injection computer, but is only allowing the start
of the vehicle’s engine. After 10 minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 27
Diag nostic
ALP2. CONTACT SET ON THE ANTI STARTING INDICATOR BLINKS
(THE ENGINE IS NOT STARTING)
RECOMMENDATION -
Set the contact on.
Connect the CLIP tester.
Is there any communication with the E.C.U.
decoder ?
S ee ALP1.
Check the fuse F03 for anti starting bushing
supply.
Is it good?Replace the fuse.
Set the c ontact on and check if the state 4D
becomes ACTIVE ?
Is th e state 19 D PASSIVE ?
Perform « Procedure for replacement
E.C.U. decoder and memorising anti
starting code » if the starter is new ;
if it’s not new, replace it.
Set the contact off. The anti starting indicator
will start to blink after 10 seconds.(ACTIVE
an ti starting ).
Set again the contact and check: the failure
« Defective communication decoder bushing ».
Does exist such a failure ?
Study « DEFECTIVE
COMMUNICATION BUSHING
– DE CODER » from the chapter
DIAGNOSTIC.
Study « STATE 4D : SUPPLY +12
V » from chapter DIAGNOSTIC.
Try the engine starting with the second key.
Is the engine starting ?Replace the first key.Yes
Ye s
Yes
Yes
Yes
Yes
No No
No
No
No
No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 30
Diag nostic
ALP4. CONTACT ON THE ANTI STARTING INDICATOR BLINKS QUICKLY
(engine is not starting)
RECOMMENDATION-
S et the contact on.
Connect the CLIP tester.
Is there any communication between the
tester and E .C.U. decoder ?
Is the state 19D, ACTIVE?
Check the continuity and the isolation related
to the mass and to the + 12V of the wiring
be t we en A6 de c ode r pi n a nd i nj e c t ion
computer pin 58.
Is the wiring good?
S ee ALP1.
Check the correct memorisation of
the anti starting code by the
E.C.U. decoder ; if not, replace
the decoder.
Fix the electric wiring.
Perform the impulse detection test by means
of the CLIP tester connected to the E.C.U.
decoder A6 pin.
Set th e conta c t on a nd c he ck i mpulse s
presence.
Are there any impulses?
Replace the injection computer.
Replace E.C.U. decoder or see t he “ Kit
replacement procedure “.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
No
Yes
No
Yes
Yes
No
Yes
No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 31
Diag nostic
ALP5. THE VEHICLE IS NOT STARTING
RECOMMENDATION-
Is there the failure “SIGNAL MISSING ON
THE CODED LINE E.C.U. DECODER –
COMPUTER INJECTION?”
There is a problem at the shock sensor.
There is an engine problem.No
Yes
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
vnx.su