2004 DACIA SOLENZA engine

84
STEERING - CONN ECTOR
84 - 4
Under steering wheel control
R EMOU NT I NG
Ensure that steering is on middle point (wheels are in the straight-on driving position of the
ve h icle).
Position the under-steering wheel control assembly so that after remounting the two steering
wheel half-cases, the assembly handles are lined up with the instrument panel and the dashboard.
Reconnect the windscreen wiper connector, the lights and turning connector and the rotating
contact connector. Attach in clips the steering wheel half-cases.
Tighten t he screw ( 2) so that i s blocking the under-steering wheel control on the steering
column. This operation is facilitated by a cutting-out in the lower half-case allowing the access to
the screw ( 2).
Carefully mount the steering wheel in order not to damage the “tape” connector of the rotating
contact, the steering wheel is having an area with no grooves, that must be corresponding to the
no-grooves area from the steering column. The steering wheel must easy enter in the grooves.
Replace the steering wheel attachment screw (TORX 50) after each dismounting and tighten
it to the required moment ( 4.4 daNm).
Reconnect the airbag connector (10.
M ount the two attachment screws TORX 20 of the airbag (required tightening moment is
0.65 daNm) Reconnect the battery (-) terminal.
Check the operation of the under steering weel control.
IMP ORTANT !
Before reconnecting the driver’s ai rbag connector, it is necessary to apply a check-
ing procedure of the system: - check if the airbag indicator from the instrument panel is on, when the contact
is set on; - connect the inert igniter to the airbag connector (to the wiring) and check if the
airbag indicator is off; - set the contact off, connect the airbag connector instead of the inert igniter and
attach the airbag on the steering wheel (required tightening m oment is 0.65 daNm). AT T E N T I ON !
Any doubts regarding a good centering of the rotating contact involves the applying
of its centering method: carefully rotate clockwise the upper part of the rotating con-
tact 2.5 complete rotations (or until it gets blocked), then rotate anti-c lockwise 2.5
complete rotations. In case of a steering dismounting operation, of t he engine or of the t ransmission
elements implying the steering rack or steering column uncoupling, the steering wheel
must be immobilized. After everything has been remounted, perform an airbag system checking by means
of the CLIP tester. If everything is correct, unblock the UCE airbag and check if the
airbag indicator from the instrument panel is on for 3 seconds from setting the contact
on, then it is off and is remaining off. If the airbag indicator is not operating as a.m .,
see chapter “Diagnostic” and check the system by means of the “CLIP” tester. AT T E N T I ON !
All non-observing of these prescriptions may c ause an abnormal operation of the
sy stem, even an undesirable starting of it.
vnx.su

86
86 - 2
AUTO RA DIO
MAIN FUNCTIONS
Function “ON / OFF Logic”
The radio may operate also when engine is stopped, when contact key is on “S” position. In
this situation, after 20 minutes of operation, an acoustic signal will be heard and the radio will
automatically stop. If you wish that radio is not stopping, after you heard the acoustic signal, push
the red starting key (1) that is enabling the radio operation for another 20 minutes.
If the contact key is brought on position “M” or “A” and the radio is started by pushing the
key (1), after the contact is set off, the radio will automatically stop. At next setting of the contact
on the position “M” or “A”, the radio will automatically start on the program set before starting.
Adjustment of the acoustic volume
By pushing the keys + or -, the acoustic volume may be adjusted, reaching its increasing or
decreasing. The acoustic volume level will be displayed in the moment of its adjustment and may
be from 0 (minim) to 30 9maxim).
Sound correction
This function is enabling the boosting or decreasing of the high /low frequencies, as well as the
balancing of the right/left and rear/front acoustic level.
RAD I O
The radio device is of multiple frequencies range, c omplex and is allowing the programs
selection in frequency range long waves (UL), medium waves (UM or ultra-short (FM).
RDS system ( Radio data System)
This system is enabling mute data transmitting , in the same time with a FM radio station signal.
The radio may use this system that is bringing the following advantages:
- emitter name displaying;
- information regarding others radio emitters;
- emergency messages;
- automatic reactivation.
Radio frequency selecti on
In order to perform this, push the key “SRC” many times so that the desired radio frequency
is selected.
General
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 1
It is located on the left side of the climate
control box, being attached by means of a
screw. It has the windscreen washing electric
pump attached on the washer reservoir.
In the drawin g, the following elements may
be identified:
1,2 Pins of the electric pump.
3 Windscreen washing reservoir
4 Electric pump
5 Attachment screw
6W ashing hose
7 Adjustable nozzle
8W ashing reservoir cap
9W ashing bushing
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the climate control gasket.
Dismount the climate control protector.
Di smount the attachment scre w of the
washing reservoir. Carefully remove the front wiring branch
(in order not to damage the splice), from its
location in the wall between the engine
compartment and the climate control box.
Extract the washing reservoir from the
washing b ushing (9). Di
sconnect t he washing hose connected to
the electric pump. Carefully remove the washing reservoir from
the climate control compartmen t and tilt it in such
way that windscreen washing fluid is not flowing
out.
R EMOU NT I NG
Perform the dismounting operations in t he
reverse order.
Check the opera tion of the assembly and
eventually adjust by means of a “needle” the
nozzle in order to correctly wash the windscreen.
AT T E N T I ON!
Do n o t clo se front bonnet after
dismounti ng the w ind scr een w a sh ing
assembly, because it may be possible the
front wiring damaging.
REMARK:
The washing fluid level must be between
the minim and maxim levels marks on the
washing reservoir (0.8 l). The required t ightening m oment of the
attachment screw of the windscreen washing
assembly: 2 Nm.
Connector
Pin Denomination
1 Windscreen washing pump control
2 Mass
Windscreen washing
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 6
Diagnostic – general
This document is presenting the diagnostic generally valid for all computers, for Cockpit
Central Unit function, at SOLENZA vehicles all types of engine
In order to perform the diagnostic of this system, it is then all-important to dispose of the
following elements:
- workshop manual of the corresponding vehicle
-electric diagram of the function, for the correspondin g vehicle
special tools specified in the column “Necessar y Special tools”.
GENERAL STEPS OF THE DIAGNOSTIC
- CLIP tester setting on, in orde r to identify the system that is equipping the vehicle
(identification of the computer family , program number, V. diagnostic..).
- Analysis of the “diagnostic” documents corresponding to the identified system.
- Acknowledgemen t of the information supplied in chapters “General”.
- Reading of the memorised failure in the computer memory and taking advantage of the
chapter “Failures interpretation”.
A TTENTION : each failure is interpreted for a specific type of memorisation : present failure
memorised failure present or memorised failure). The specified checking for handling each
failure a re not to be a pplied on the vehicle unless the declare d failure is i nterpre ted in t he
document for its specific memorising type. The memorising type must be taken into consideration
w hen the tester is set on after setting off and on of the contact .
If a failure is interpreted in the moment when it is declared “memorised”, the di agnostic
application conditions are present in “Recommendations”. If the conditions are not fulfilled, you
must take the ideas from the diagnostic of damaged element circuit checking, be cause t he
failure is not anymore present on the vehicle. Apply the same method when a failure is declared
as been memorised by the diagnostic tester, but it is interpreted in the documentation only as
< state.
- Performing the conformity checking (accentuation of the possible failures, non-declared
yet by the system self-diagnostic) and application of the adequate diagnostic according to the
results.
- Reparation validation (elimination of “client’s effect”)
- Diagnostic exploitation by “Client’s effect” if the problem still on.
N ECESSARY SPECIAL TOOLS FOR INTERVENTION
- CLIP diagnostic tester
- All-purpose meter
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 8
Diagnostic - General
CONNECTION (the most complete)
Black connector EH1 ( 40 pins)
PIN DENOMINATION 1Not used
2Not used
3Not used
4Not used
5 Not used
6 Not used
7 Not used
8D oors locking switch inlet
( doors unlocking control)
9Not used
10 Not used
11 N o t u s e d
12 Not used
13 Not used
14 Not used
15 Parking lights inlet
16 Decoding bushing inlet
17 Doors locking switch inlet
(doors locking control)
18 Not used
19 Not used
20 Not used
21 Not used
22 + After contact
23 Not used
24 Windscreen wiper timer inlet
25 Not used
26 Left turning inle t
27 Not used
28 Right turning inlet
29 Not used
30 Not used
31 Not used
32 Anti-starting indic ator inlet
33 Hazard lights inlet
34 Diagnostic line K
35 Not used
36 Engine anti-starting outlet
37 Not used
38 Not used
39 Not used
40 Driver’s door contact inlet White connector P1 (15 pins)
PIN DENOMINATION
A1 Mas s
A2 Ceiling lamp outlet
A3 + Before contact
A4 Windscreen wiper control
A5
Windscreen wiper supply (+ after
contact)
A6 Windscreen wiper fix point stopping
A7 Not used
A8 Right turning outlet
A9 Left turning outlet
B1 Not used
B2 Doors locking outlet
B3 Doors locking/unlocking supply
B4 Doors unlocking outlet
B5 Ceiling amp timer outlet
B6 Ceiling lamp supply
P1 EH1
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 14
Diagnostic - Conformity checking
RECOMMENDATIONS Do not perform this conformity checking but after a competechecking by means of diagnostic tester. The values
displayed in this conformity checking are only informative.
The execution condition: stopped engine, contact set on.
1
2 Supply
Lighting PR002
: Battery voltage
ET002: +12 V after
c ontact
ET309: Right turning
information
ET310: L eft turning
information
ET291: H azard lights
information 12V < X
< 12,5V
Presen t
It is ACTIVE when
c ontrolling r ight
turning
It is ACTIVE when
controlling left turning
It is ACTIVE when
controlling hazard lights If problems occurring:
Perform a diagnostic of the charging circuit
If problems occurring: See state diagnostic
ET002
If is INACTIVE , see
state diagnostic ET309
If it is INACTIVE , see
state diagnostic ET310
If it is INACTIVE , see
state diagnostic ET291
No.
Function Par
ameter or state
Checking or action Visualization and
observations
Diagnos tic
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 15
Diagnostic - Conformity checking
RECOMMENDATIONS Do not perform this conformity checking but after a competechecking by means of diagnostic tester. The values displayed
in this conformity checking are only informative.
The execution condition: stopped engine, contact set on.
3
4 Wiper
Opening ET213:
Windscreen
wiper timing
ET005: Windscreen
wiper fix point sto pping
ET192: : Front doors ACTIVE
, when
windscreen wi p e r
control in on timer
position
ACTIVE when
c ontrolling the wiper
on timer position, at
each wipe r stopping.
State OPEN when
opening the driver’s
doors If
it INACTIVE , see
state diagnostic ET213.
If problems occurring, apply the specific
diagnostic for
windscreen wiper fix point stopping failure DF119
If prob lems occurring: see
state diagnostic ET 192
No.
Function Par
ameter or state
Checking or action Visualization and
observations
Diagnos tic
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 16
Diagnostic - Conformity checking
Do not perform this conformity checking but after a compete
checking by means of diagnostic tester. The values displayed
in this conformity checking are only informative.
The execution condition: stopped engine, contact set on.
RECOMMENDATIONS
Par ameter or state
Checking or action
ET010: Key RF valid
ET193: RF information
r eceived
ET012: source of last
r eceived co ntrol
ET105: Last received
c ontrol Visualization and
observations
State YES when
doors locking or
unlocking is done
using a remote control a ssigned to that UCH
.
State YES when
doors blocking/
unlocking is done using the remote
control
TRF when doors
locking/unloc king is
done u sing the remote
cont rol, CP E when
locking/unloc king is
done u sing the doors
central locking switch
UNL OCKI NG LOCK ING Diagnos tic
If problems occurring: see state diagnostic ET010
If problems occurring: see state diagnostic ET193
Nothing to notice
Nothing to notice
No.
1F unction
Opening
(ctd)
vnx.su