2004 DACIA SOLENZA engine

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 36
Diag nostic
THE CONFORMITY CHECKING
N ext, the checking of different states and configurations of the anti starting system is to be
performed.
RECOMMENDATION In case of finding some failures at the diagnostic by means of
the CLIP tester, analyse them based on the diagnostic (ALP)
corresponding to the respective failure.
Crt. Function State/ configuration Obse rvations
Nr. 1. Conformity E.C.U decoder. Computer identification Display of the E.C.U. decoder item.
2. Remote control type 2G = remote control IR = infrared configuration RF = radio frequency
3. Ceiling delayed lamp Without ceiling delayed lamp or Validation on the blue button with ceiling delayed lamp on CLIP screen.
4. Key programming 3G = configuration key With one or 2 keys. programming
5. Configuration petrol/ diesel 3D = configuration coded diesel Without = for petrol engine
electric valve. or diesel without electric
valve.
6. Forced starting protection 9D = forced protecting mode ACTIVE = only after validation on the blue button.
7. Anti starting state 10G = anti starting ACTIVE = with the contact
taken off or after 10 seconds
from th e contact taken off.
8. Key presence 8D = key present ACTIVE at the setting on
the contact if there is a
coded key.
REMARK: the states 8D,
9D, 10 D must be ACTIVE
at a correc t operation.
9. Code key receiving 9D = received key code ACTIVE at the setting on
the contact if the key is
coded in a good format.
10. Correct key code 10D = right key code ACTIVE at the setting on the contact if the key is
coded in a good format and
has the correct code.
REMARK: after the analyse
of the states 8D, 9D, 10 D
the contact will be set on
when the LED indicator
b links ( ACTIVE anti
starting).
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 43
OPERATION
When anti-starting system is on, the red LED is blinking (rare signal: one blink/sec).
After setting the contact on, the key code is transmitted to the Cockpit Central Unit.
If the code is recognized by the Cockpit Central Unit, this one is sending coded signals to the
injection computer and the anti-starting LED is off.
If signals issued by the Cockpit Central Unit and by the injection computer are matching, the
Cockpit Central Unit is authorizing the engine starting and the injection is unlocked.
SPECI AL SI TUATIONS
Injection computer does not have any reference code in m emory: the code sent by UCH is
written in the memory .
If there is no matching of the key c odes / Cockpit Central Unit, t he system is remaining
blocked and anti-star ting LED is blinking (quick signal). The vehicle starting is not authorized.
AT TE NT ION: when the battery is low charged, the voltage drop further to starter
action may reactivate the anti-starting. If voltage is too low, starting is impossible.
Key recognition in normal operation
Anti-starting indicator
Protected vehicle (without + after contact) Indicator slow blinking
Recognized key, non protected injection Indicator lighted for 3 seconds, then set off.
Non-recognized key Indicator is quickly blinking (at 4 Hertz)
Diagnostic – General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 52
Diagnostic – General
THE CODING OF THE INJECTION COMPUTER.
The injection c omputer i s delivered not coded. Therefore, t he anti-starting system code
memorizing will be necessary, when its mounting, in order to authorize the vehicle starting.
It is sufficient to set the contact on for fe w seconds, without starting the engine. Set the
contact off and the anti-starting function will be ensured after few seconds (anti-starting red
LED is blinking)
ATT E NT ION:
By means of this anti-star ting system, the vehicle is keeping its own anti-starting code on all
its lifetime. Furthermore, this system does not have a breakdown code. Therefore, it is forbidden
to perform tests with injection computers borrowed from warehouse that must be a fter that
returned. The code memorized by the injection computer can not be anymore erased.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 53
AFTER REPAIRINGRemediaπi celelalte eventuale defecπiu ni .
ªtergeπi defectele memorat
e.
RECOMMENDATIONSApplying conditions of the diagnostic to the memorized failure :
- failure declared present when setting the contact on (+After contact).
Diagnostic – Failures interpretation
DF055
PRESENT
OR
ME MO RIZED
CODED LINE CIRCUIT
Check the connection and condition of the connector with 40 pins EH1 of the Cockpit Central Unit.
If necessary, repair the connector.
Check the continuity and insulation of the connection:
Connector EIII with 40 pi ns Cockpit central Unit pin B36 i njection computer
(see the corresponding engine electric diagram)
If necessary, fix it.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 55
Do not perform this checking but only after a complete check-up by
means of the diagnostic tester. The values showed in this conformity
checking are mentioned only for your information.
Execution condition: stopped engine, contact set on.
Diagnostic – Conformity checking
RECOMMENDATIONS
Function
Supply
Anti-starting
Programming Par
ameter or state
Checking or action
ET154: present +12V
A fter contact
PR065 : no of pro-
gramme d keys
ET002: received key
c ode
ET003: valid key code
ET017: active anti-start-
in g
ET130: anti-starting
LED
ET110 : empty Cockpit
centra l Unit Visualization and
remarks
YES
2 ke ys at new ve-
hicle; up to
4 keys programming
after-sale
State YES when con-
tact set on
State YES when
co ntact set on
NO
OFF Diagnos tic
If problems occurring:
S ee the diagnostic of
state ET154
Nothing to notice
If problems occurring:
See the diagnostic of the
state ET002
If problems occurring:
See the diagnostic of the
state ET003
If problems occurring:
See the diagnostic of the
state ET017
If problems occurring:
See the diagnostic of the
state ET130
If state” Empty Cockpit
cent ral Un it” is YE S ,
see the pr ogrammi ng
procedu re.
No.
1
2
3
NO
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 63
Diagnostic – Damage location algorithm
AL P1
There is no communication with the computer
RECOMMENDATIONS Nothing to notice
Check the communication of CLIP tester with a computer from another vehicle.
Check:
- connection between CLIP tester and the diagnostic socket (check the cable c ondition).
Cockpit and engine compartment fuses.
Check presence +1 2 volts befor e c ontact at pin 16, + 12 volts after contact at pin 1
and mass at pins 4 and 5 of the di agnostic socket
Fix it if necessary.
Connect the multi-socket and check the insulation, continuity and absence of parasite resis-
tance at connections:
Pin A3 of UCH connector P1 with 15 pins fuse box
Pin 22 of UCH connector E H1 with 40 pins + after contact
Pin A1 of UCH connector P1 with 15 pins mass
Pin 34 of UCH connector EH1 with 40 pins pin 7 diagnostic socket (line K).
Fix it if necessary.
Check the system operation
AFTER REPAIRING
vnx.su

83
INSTRUMENT PANEL
83 - 3 Con
nector D (gray)
Pin Denomination 1. Mass
2. Free
3. Free
4. Free
5. Water temperature alert
6. Oil pressure alert
7. Battery charging indicator
8. Fog lamp indicator
9. Fog projectors indicator
10. Right turning indicator
C
onnector C (black)
Pin Denomination 1. Free
2. Free
3. Free
4. Handbrake indicator / ICP braking
system
5. Free
6. Anti-starting indicator
7. – Fuel level transmitter
8. Fuel level signal
9. Free
10. + Battery
Connector A (white)
Pin Denomination 1. Left turning indicator
2. Meeting lights indicator
3. Road lights indicator
4. Rear windscreen defrosting indicator
5. Free
6. Free
7. Free
8. + Parking lights
9. Water temperature indicator
10. Free
Connectors disposal
Connector B (brown)
Pin Denomination 1. Vehicle speed signal
2. Engine RPM signal
3. Free
4. Free
5. + After contact
6. Driver safety belt indicator
7. OBD indicator
8. Free
9. Free
10. + After contact
vnx.su

INSTRUMENT PANEL
83
83 - 8
Diagnostic – damages interpretation
Check the oil pressure.
Pr essure is correct?
Replace the oil pressure transmitter. There is a failure in the oil circuit.
Fix it.
OIL P RESSURE INDICATOR IS NOT ON WHEN CONTACT SET ON
Place the wire from the oil pressure
transmitter to the mass Is the indicator on ?
Replace the oil
pressure transmitter Replace the bulb.
Wa r
ning indicator bulb is
worn?
Check the bulb supply wiring and fix it.
FUEL LEVEL INDICATOR SHOWING ALWAYS FULL
Replace the fuel level transmitter.
Replace the instrument panel. Disconnect the connection wire t o the probe.
Is the fuel level indicator showing zero ?
Resistance against the vehicle mass of the B1 pin
of the fuel level transmitter connector is zero?
Defective wiring. Fix it.Ye s
No
Ye s N o Ye sNo
Ye s No No
Ye s
OIL PRESSURE INDICATOR STILL ON
AFTER ENGINE STARTING
vnx.su