2003 NISSAN X-TRAIL transmission

AT-526
[ALL]
REPAIR FOR COMPONENT PARTS
3. Remove snap ring from bearing retainer.
4. Remove needle bearing from bearing retainer.
5. Remove idler gear bearing inner race from idler gear.
6. Remove idler gear bearing outer race from transmission case.
7. Press out reduction pinion gear bearing inner race from reduc-
tion pinion gear.
SAT166F
SAT167F
SAT168F
SAT859DD
SAT169F

AT-528
[ALL]
REPAIR FOR COMPONENT PARTS
ASSEMBLY
1. Press reduction pinion gear bearing inner race on reduction pin-
ion gear.
2. Install reduction pinion gear bearing outer race on transmission
case.
3. Press idler gear bearing inner race on idler gear.
4. Install idler gear bearing outer race on transmission case.
SAT172FC
: 109 - 123 N-m (11.1 - 12.5 kg-m, 80 - 90 ft-lb)
SAT319K
SAT174FC
SAT175FD

AT-530
[ALL]
REPAIR FOR COMPONENT PARTS
lRoll paper around seal rings to prevent seal rings from
spreading.
Band Servo Piston AssemblyECS004MB
COMPONENST
DISASSEMBLY
1. Remove band servo piston fixing bolts.
2. Apply compressed air to oil hole in transmission case to remove
O/D servo piston retainer and band servo piston assembly.
lHold band servo piston assembly with a rag or nylon
waste.
SAT179F
AAT293A
AAT879
SAT093J

AT-534
[ALL]
REPAIR FOR COMPONENT PARTS
5. Install band servo piston assembly to servo piston retainer by
pushing it inward.
6. Install D-ring to O/D servo piston.
lApply ATF to D-ring.
7. Install O-rings to O/D servo piston retainer.
lApply ATF to O-rings.
lPay attention to position of each O-ring.
8. Install O/D servo piston to O/D servo piston retainer.
9. Install band servo piston assembly and 2nd servo return spring
to transmission case.
lApply ATF to O-ring of band servo piston and transmis-
sion case.
SAT303D
AAT881
AAT882
AAT886
SAT865H

REPAIR FOR COMPONENT PARTS
AT-535
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
10. Install O/D servo piston assembly to transmission case.
lApply ATF to O-ring of band servo piston and transmis-
sion case.
11. Install O/D servo piston retainer to transmission case.
Refer toAT- 4 6 4 , "
Oil Channel".
Final DriveECS004MC
COMPONENTS
DISASSEMBLY
1. Remove final gear.
AAT885
AAT879
SCIA0807E
SMT505B

AT-536
[ALL]
REPAIR FOR COMPONENT PARTS
2. Press out differential side bearings.
lBe careful not to mix up the right and left bearings.
3. Remove differential side bearing outer race, and side bearing
adjusting shim from transmission case.
4. Remove speedometer drive gear.
5. Drive out pinion mate shaft lock pin.
SMT744AA
SAT010FA
SAT313D
SAT904DA

AT-540
[ALL]
ASSEMBLY
ASSEMBLY
PFP:00000
Assembly (1)ECS0 04 MD
1. Install differential side oil seals on transmission case and con-
verter housing.
2. Install parking actuator support to transmission case. Tighten
parking actuator support bolts to the specified torque. Refer to
AT-461, "
OVERHAUL"$$$$$.
lPay attention to direction of parking actuator support.
3. Install parking pawl on transmission case and fix it with parking
shaft.
4. Install return spring.
SAT181FC
SAT182F
SAT183F
SAT039F

ASSEMBLY
AT-541
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
Adjustment (1)ECS004ME
DIFFERENTIAL SIDE BEARING PRELOAD
1. Install differential side bearing outer race without adjusting shim
on transmission case.
2. Install differential side bearing outer race on converter housing.
3. Place final drive assembly on transmission case.
4. Install transmission case on converter housing. Tighten trans-
mission case fixing bolts to the specified torque. Refer toAT-
461, "OVERHAUL".
5. Attach dial indicator on differential case at converter housing
side.
6. Insert Tool into differential side gear from transmission case
side.
7. Move Tool up and down and measure dial indicator deflection.
8. Select proper thickness of differential side bearing adjusting
shim(s).
Suitable shim thickness = Dial indicator deflection + Speci-
fied bearing preload
SAT870D
SAT008F
Differential side bearing preload adjusting shim :
Refer toAT-563, "
SERVICE DATA AND SPECIFICA-
TIONS (SDS)".
Bearing preload :
0.05 - 0.09 mm (0.0020 - 0.0035 in)
SAT186FA