2003 NISSAN TEANA bulb

LT-170
TURN SIGNAL AND HAZARD WARNING LAMPS

5. CHECK CIRCUIT BETWEEN TURN SIGNAL LAMP AND GROUND
1. Turn ignition switch OFF.
2. Check continuity between front combination lamp LH harness
connector and ground.
3. Check continuity between side turn signal lamp LH harness con-
nector and ground.
4. Check continuity between rear combination lamp LH harness
connector and ground.
OK or NG
OK >> Check turn signal lamps LH bulbs.
NG >> Repair harness or connector.
Turn Signal Lamps Do Not Operate But Hazard Warning Lamp OperateBKS0040D
1. CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-II
1. Select “BCM” on CONSULT-II, and select “FLASHER” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “TURN SIGNAL R” and “TURN SIGNAL L” turns
ON-OFF according to turn signal switch operation.
Without CONSULT-II
Refer to LT- 1 8 5 , "
Combination Switch Inspection" .
OK or NG
OK >> Replace BCM. Refer to BCS-16, "Removal and Installation of BCM" .
NG >> Check combination switch (lighting switch). Refer to LT- 1 8 5 , "
Combination Switch Inspection" .
Headlamp typeFront combination
lamp LH connectorTerminal
GroundContinuity
Xenon E29
4Yes
Conventional E46
SKIB8819E
Side turn signal
lamp LH connectorTerminal
GroundContinuity
E43 2 Yes
PKID0098E
Rear combination
lamp LH connectorTerminal
GroundContinuity
B34 2 Yes
PKID0099E
When turn signal switch is
in the RH position: TURN SIGNAL R ON
When turn signal switch is
in the LH position: TURN SIGNAL L ON
PKIA7600E

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-175
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001PZ
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer to LT- 1 7 5 , "Removal and Installation" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 5 , "Bulb Replacement" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS001Q2
SIDE TURN SIGNAL LAMP
Removal
1. While pressing side turn signal lamp to direction A (vehicle
front), pull it to direction B and then remove it.
2. Disconnect side turn signal lamp connector.
NOTE:
Support side turn signal lamp harness with tape so that it won't
fall into the front fender.
CAUTION:
Install the side turn signal lamp housing with the bead fac-
ing up.
Installation
Installation is the reverse order of removal.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 6 , "Removal and Installation" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . Side turn signal lamp : 12V - 5W
PKIA0015E
SKIA7249E

LT-192
STOP LAMP

Bulb ReplacementBKS001QD
HIGH-MOUNTED STOP LAMP
Replacement integral with high-mounted stop lamp. Refer to LT- 1 9 2 , "Removal and Installation" .
STOP LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040N
HIGH-MOUNTED STOP LAMP
Removal
1. Remove rear parcel shelf finisher. Refer to EI-43, "Removal and Installation" .
2. Disconnect high-mounted stop lamp connector.
3. Remove high-mounted stop lamp mounting screws and remove
high-mounted stop lamp from rear parcel shelf finisher.
Installation
Note the following, and installation is the reverse order of removal.
STOP LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . High-mounted stop lamp : LED
SKIA6346E
High-mounted stop lamp
mounting screws: 3.15 N·m (0.32 kg-m, 28in-lb)

BACK-UP LAMP
LT-195
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001QI
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040G
Refer to LT- 2 1 6 , "Removal and Installation" .

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-211
C
D
E
F
G
H
I
J
L
MA
B
LT

6. CHECK CIRCUIT BETWEEN PARKING, LICENSE PLATE, TAIL LAMPS AND GROUND
1. Check continuity between front combination lamp harness con-
nector and ground.
2. Check continuity between rear combination lamp harness con-
nector and ground.
3. Check continuity between license plate lamp harness connector
and ground.
OK or NG
OK >> Check bulbs.
NG >> Repair harness or connector.
Headlamp typeFront combination
lamp connectorTerminal
GroundContinuity
XenonRH E15
4Yes LH E29
HalogenRH E47
LH E46
PKIA6298E
Rear combination lamp Terminal
GroundContinuity
RH B24
2Yes
LH B33
PKID0109E
License plate lamp connector Terminal
GroundContinuity
RH T3
2Yes
LH T4
PKIB7990E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-215
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001QX
LICENSE PLATE LAMP
1. Remove trunk lid finisher inner. Refer to EI-59, "REMOVAL AND
INSTALLATION FOR TRUNK LID FINISHER INNER" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb from its socket.
PARKING LAMP
Refer toLT- 3 5 , "Bulb Replacement" .
TAIL LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040M
LICENSE PLATE LAMP
Removal
1. Remove trunk lid finisher. Refer to EI-33, "Removal and Installa-
tion" .
2. While pressing the license plate lamp to left side, pull right side
of it and remove.
3. Disconnect license plate lamp connector.
Installation
Installation is the reverse order of removal.
PARKING LAMP
Refer to LT- 3 6 , "Removal and Installation" .
TAIL LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . License plate lamp : 12V - 5W
SKIA6350E
SKIA6349E

LT-216
REAR COMBINATION LAMP

REAR COMBINATION LAMPPFP:26554
Bulb ReplacementBKS001R0
REAR TURN SIGNAL LAMP BULB, BACK-UP LAMP BULB AND STOP/TAIL LAMP BULB
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Turn tail lamp bulb socket (1), rear turn signal lamp bulb socket
(2), back-up lamp bulb socket (3) (right side) and rear fog lamp
bulb socket (3) (left side) counterclockwise and unlock it.
3. Remove tail lamp bulb (4), rear turn signal lamp bulb (5), back-
up lamp bulb (6) (right side) and rear fog lamp bulb (6) (left
side).
Removal and InstallationBKS001R1
REMOVAL
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting nuts (A).
4. Pull the rear combination lamp (1) toward rear of the vehicle and
remove clip (B) and locating pin (C) from the vehicle.
5. Remove seal packing (2) from rear combination lamp (1).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Seal packing cannot be reused.Tail lamp : 12V - 5W
Rear turn signal lamp : 12V - 21W
Back-up lamp (Right side) : 12V - 21W
Rear fog lamp (Left side) : 12V - 21W
Stop lamp : LED
SKIB8646J
PKIC9679J
Rear combination lamp mounting nut : 5.1 N·m (0.52 kg-m, 45 in-lb)

LT-218
INTERIOR LAMP

Bulb ReplacementBKS002EL
VANITY MIRROR LAMP
1. Insert a thin screwdriver in the lens and remove lens.
2. Remove bulb together with substrate.
Vanity mirror lamp : 12V - 1.8W
SKIB0902E