2003 NISSAN TEANA Oil filter

EM-26
[QR]
OIL PAN AND OIL STRAINER

OIL PAN AND OIL STRAINERP F P : 1111 0
Removal and InstallationBBS00590
REMOVAL
WARNING:
To avoid the danger of being scalded, do not drain the engine oil when the engine is hot.
NOTE:
When removing oil pan (lower) or oil strainer only, take step 2 then step 8 and 9, the other steps are unneces-
sary.
1. Remove undercover and splash guard (RH).
2. Drain engine oil. Refer to LU-9, "
Changing Engine Oil" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine oil on drive belt.
3. Remove drive belt. Refer to EM-14, "
DRIVE BELTS" .
4. Remove exhaust front tube. Refer to EX-2, "
EXHAUST SYSTEM" .
5. Remove A/C compressor with piping connected. And locate it aside temporarily with ropes or equivalent
not to disturb the following work. Refer to ATC-134, "
Removal and Installation of Compressor" .
6. Remove oil level gauge guide.
7. Remove oil filter. Refer to LU-10, "
OIL FILTER" .
8. Remove oil pan (lower) with the following procedure:
1. Oil level gauge 2. Oil level gauge guide 3. O-ring
4. Oil pan (upper) 5. Cylinder block 6. O-ring
7. Oil filter 8. O-ring 9. Drain plug washer
10. Oil strainer 11. Drain plug 12. Oil pan (lower)
13. Rear plate cover
PBIC2177E

OIL PAN AND OIL STRAINER
EM-145
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

OIL PAN AND OIL STRAINERP F P : 1111 0
Removal and InstallationBBS004VU

Refer to GI-10, "Components" for symbol marks in the figure.
REMOVAL
WARNING:
To avoid the danger of being scalded, do not drain engine oil when engine is hot.
NOTE:
When removing oil pan (lower) or oil strainer only, take step 1 then step 10 and 11.
1. Drain engine oil. Refer to LU-21, "
Changing Engine Oil" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine oil on drive belts.
2. Drain engine coolant. Refer to CO-34, "
Changing Engine Coolant" .
1. Oil pan (upper) 2. O-ring 3. Oil pan gasket (front)
4. Oil pressure switch 5.Plug (VQ23DE)
Relief valve (VQ35DE)6. O-ring
7. Oil cooler 8. Connector bolt 9. Oil filter
10. Oil strainer 11. Drain plug 12. Drain plug washer
13. Oil pan (lower) 14. Rear plate cover 15. Harness bracket
16. Crankshaft position sensor (POS) 17. Seal rubber 18. Oil pan gasket (rear)
A. Refer to LU-22
B. To oil pump C. Oil pan side
D. VQ23DE E. VQ35DE
PBIC4533J

EM-146
[VQ]
OIL PAN AND OIL STRAINER

CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belts.
3. Remove the following:

Engine cover; Refer to EM-133, "INTAKE MANIFOLD COLLECTOR" .

Splash guard (RH)

Exhaust front tube; Refer to EX-2, "EXHAUST SYSTEM" .

Drive belts; Refer to EM-128, "DRIVE BELTS" .
4. Remove A/C compressor with piping connected, and temporarily secure it to aside. Refer to ATC-133,
"Components" .
5. Remove three way catalysts (right and left banks) from exhaust manifolds (right and left banks). Refer to
EM-140, "
EXHAUST MANIFOLD AND THREE WAY CATALYST" .
6. Remove oil pressure switch. Refer to LU-20, "
OIL PRESSURE CHECK" .
7. Remove crankshaft position sensor (POS).
CAUTION:

Handle carefully to avoid dropping and shocks.

Do not disassemble.

Do not allow metal powder to adhere to magnetic part at sensor tip.

Do not place sensor in a location where it is exposed to magnetism.
8. Remove oil filter. Refer to LU-22, "
OIL FILTER" .
9. Remove oil cooler and water pipes (VQ35DE). Refer to LU-23, "
OIL COOLER (VQ35DE)" .
10. Remove oil pan (lower) as follows:
a. Loosen mounting bolts in the reverse order as shown in the fig-
ure.
b. Insert seal cutter (SST) between oil pan (lower) and oil pan
(upper).
CAUTION:

Be careful not to damage the mating surfaces.

Do not insert screwdriver, this will damage the mating
surfaces.
c. Slide seal cutter by tapping on the side of the tool with hammer.
Remove oil pan (lower).
PBIC0782E
SEM365ED

IDX-2
ALPHABETICAL INDEX
Numerics
3rd position switch ............................. AT-161
, AT-210
A
A/C air flow ...................................................... ATC-31
A/C component layout ..................................... ATC-20
A/C compressor clutch removal and installation ...........
ATC-136
A/C compressor mounting ............................. ATC-134
A/C compressor precaution ............................. ATC-11
A/C compressor special service tool ................ ATC-15
A/C control operation (auto A/C) ...................... ATC-29
A/C diagnostic work flow (auto A/C) ................ ATC-94
A/C evaporator ............................................... ATC-144
A/C HFC134a (R134a) system precaution ........ ATC-5
A/C HFC134a (R134a) system service procedure .......
ATC-131
A/C HFC134a (R134a) system service tools ... ATC-16
A/C HFC134a system service equipment precaution ...
ATC-12
A/C lubricant (R134a) ...................................... ATC-21
A/C lubrication oil ........................................... ATC-150
A/C operational check ...................................... ATC-54
A/C self-diagnoses (auto A/C) .......... ATC-46, ATC-94
A/C service data specification ........................ ATC-150
A/C system description (auto A/C) ................... ATC-24
A/C, A - Wiring diagram ................................... ATC-39
A/T fluid checking .................................. AT-14, MA-35
A/T fluid replacement ............................. AT-15, MA-36
A/T IND - Wiring diagram .................................... DI-48
A/T shift control system ................................... AT-213
A/T shift lock system ........................................ AT-216
A/T shift lock system - Wiring diagram ............ AT-217
A/T trouble diagnoses ........................................ AT-34
Accelerator control system ............................... ACC-3
Accelerator pedal position (APP) sensor ........ EC-251,
EC-258
, EC-272, EC-631, EC-638, EC-652
Accelerator pedal released position learning .... EC-47,
EC-389
AFS ..................................................................... LT-75
AFS - Wiring diagram ......................................... LT-79
Air bag .............................................................. SRS-3
Air bag disposal .............................................. SRS-48
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(QR20DE) .................... EM-17
Air cleaner and air duct(VQ23DE and VQ35DE) ..........
EM-131
Air cleaner filter replacement(QR20DE) ........... MA-20
Air cleaner filter replacement(VQ23DE and VQ35DE) .
MA-30
Air cleaner filter(QR20DE) ................................ EM-17
Air cleaner filter(VQ23DE and VQ35DE) ........ EM-132
Air conditioner cut control .................... EC-25, EC-362
Air flow meter - See Mass air flow sensor ...... EC-124,
EC-466
Air mix. door motor ......................... ATC-66, ATC-124
Ambient sensor ............................... ATC-96, ATC-109
Angular tightening application(QR20DE) ............ EM-6
Angular tightening application(VQ23DE and VQ35DE)
EM-120
Antenna ............................................................. AV-38
APPS1 - Wiring diagram ................... EC-253, EC-633
APPS2 - Wiring diagram ................... EC-260, EC-640
APPS3 - Wiring diagram ................... EC-274, EC-654
ASC/BS - Wiring diagram ................................ EC-605
ASC/SW - Wiring diagram ............................... EC-597
ASCBOF - Wiring diagram ............................... EC-661
ASCD ............................................................... EC-363
ASCD (automatic speed control device) ........... ACS-2
ASCD brake switch ........................... EC-602, EC-660
ASCD indicator lamp ....................................... EC-667
ASCD steering switch ...................................... EC-595
ASCIND - Wiring diagram ................................ EC-668
AT indicator lamp ................................................ DI-48
Audio ........................................................ AV-4, AV-18
AUDIO - Wiring diagram .......................... AV-7, AV-21
Auto air conditioner - Wiring diagram ............. ATC-39
Auto amp ...................................................... ATC-108
Auto anti-dazzling inside mirror ....................... GW-80
Automatic amplifier ........... ATC-44, ATC-56, ATC-108
AV communication line .......................... AV-49, AV-73
Axle ................................................................... MA-42
B
BA/FTS - Wiring diagram ................................. AT-111
BACK/L - Wiring diagram ................................. LT-193
Back-up lamp ................................................... LT-193
Basic inspection .................................. EC-40, EC-381
Battery ................................................................. SC-4
BCM (Body control module) .............................. BCS-3
Blower motor ................................... ATC-72, ATC-115
Blower unit .................................................... ATC-113
Boring/horning cylinder block(QR20DE) ......... EM-104
Boring/horning cylinder block(VQ23DE and VQ35DE) .
EM-250
Brake fluid level ................................................ MA-40
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-41
Brake lines and cables inspection .................... MA-40
Brake pedal .......................................................... BR-6
Brake switch ......... EC-245, EC-602, EC-626, EC-660
BRK/SW - Wiring diagram ................ EC-247, EC-627
Bulb specifications ........................................... LT-261
Bumper, front ...................................................... EI-14
Bumper, rear ....................................................... EI-17
C
Camshaft inspection(QR20DE) ........................ EM-44
Camshaft inspection(VQ23DE and VQ35DE) EM-194
Camshaft position sensor (PHASE) .. EC-176, EC-524
Camshaft(QR20DE) .......................................... EM-41
Camshaft(VQ23DE and VQ35DE) .................. EM-192
CAN - Wiring diagram ......... EC-114, EC-459, AT-134,
CVT-54

IDX-4
ALPHABETICAL INDEX
Electric throttle control actuator (VQ23DE and VQ35DE)
EM-137
Electrical load signal circuit ................ EC-280, EC-670
Electrical unit ..................................................... PG-74
Electrical units location ...................................... PG-67
Electronic ignition (EI) system ............. EC-23, EC-360
EMNT - Wiring diagram ................................... EC-673
ENG SS - Wiring diagram ................................ AT-117
Engine control circuit diagram ............. EC-70, EC-413
Engine control component parts location .......... EC-64,
EC-406
Engine control module (ECM) ............ EC-190, EC-538
Engine control system diagram and chart ........ EC-20,
EC-357
Engine coolant temperature sensor (ECTS) ... EC-131,
EC-474
Engine coolant(QR20DE) ................................. CO-10
Engine coolant(VQ23DE and VQ35DE) ........... CO-34
Engine fail-safe system ........................ EC-59, EC-401
Engine mounting control (Front) ...................... EC-672
Engine oil filter replacement(QR20DE) ............. MA-21
Engine oil filter replacement(VQ23DE and VQ35DE) ...
MA-31
Engine oil precautions .......................................... GI-8
Engine oil replacement(QR20DE) .................... MA-20
Engine oil replacementVQ23DE and VQ35DE . MA-30
Engine oil(QR20DE) ............................................ LU-7
Engine oil(VQ23DE and VQ35DE) .................... LU-19
Engine removal(QR20DE) ................................ EM-77
Engine removal(VQ23DE and VQ35DE) ........ EM-223
Engine trouble diagnoses ................................ EC-394
ETC1 - Wiring diagram ...................... EC-201, EC-556
ETC2 - Wiring diagram ...................... EC-209, EC-564
ETC3 - Wiring diagram ...................... EC-214, EC-569
EVAP canister ...................................... EC-29, EC-369
EVAP canister purge volume control solenoid valve ....
EC-282
, EC-677
EVAP vapor lines inspection ............................. MA-23
EVAP vapor lines inspection(VQ23DE and VQ35DE) ..
MA-34
EVAP vapor lines inspectionVQ23DE and VQ35DE ....
MA-33
Evaporative emission (EVAP) system . EC-27, EC-366
Evaporator ..................................................... ATC-144
Exhaust manifold(QR20DE) ............................. EM-23
Exhaust manifold(VQ23DE and VQ35DE) ..... EM-140
Exhaust system ................................................... EX-2
Exhaust system inspection ..................... EX-2, MA-35
Expansion valve ............................................. ATC-145
F
F/FOG - Wiring diagram ................................... LT-129
F/LID - Wiring diagram ....................................... BL-45
F/PUMP - Wiring diagram .................. EC-296, EC-691
Floor trim ............................................................. EI-52
Flow charts ......................................................... GI-24
Fluid temparature sensor (CVT) ...................... CVT-69
Fluids ................................................................ MA-14
Fluorescent leak detector ............................. ATC-146
Fog lamp, front ................................................. LT-126
Freeze frame data .............................. EC-35, EC-376
FRO2 - Wiring diagram ..................... EC-302, EC-309
FRO2B1 - Wiring diagram ................ EC-697, EC-707
FRO2B2 - Wiring diagram ................ EC-699, EC-709
Front bumper ...................................................... EI-14
Front door ............................. BL-119, BL-123, GW-46
Front fog lamp .................................................. LT-126
Front passenger air bag .................................. SRS-39
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-46
Front side air bag ............................................ SRS-40
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTS - Wiring diagram ...................................... CVT-70
Fuel cut control (at no load high engine speed) EC-24,
EC-361
Fuel gauge ............................................................ DI-4
Fuel injector and fuel tube(QR20DE) ................ EM-34
Fuel injector and fuel tube(VQ23DE and VQ35DE) ......
EM-155
Fuel lid opener, electric ...................................... BL-44
Fuel line inspection .............................................. FL-3
Fuel line inspection(QR20DE) .......................... MA-20
Fuel line inspectionVQ23DE and VQ35DE ....... MA-30
Fuel pressure check ........................... EC-49, EC-392
Fuel pressure release ......................... EC-49, EC-392
Fuel pump ......................................... EC-295, EC-690
Fuel pump and gauge .......................................... FL-4
Fuel system ......................................................... FL-3
Fuel tank .............................................................. FL-8
Fuel tank vacuum relief valve ............. EC-29, EC-369
Fuse .................................................................. PG-16
Fuse and fusible link box .................................. PG-80
Fusible link ........................................................ PG-16
G
Gauges ................................................................. DI-4
Glass ...................................... GW-11, GW-46, GW-50
Grease .............................................................. MA-14
Grille - See Exterior ............................................ EI-20
Ground distribution ........................................... PG-29
H
H/AIM - Wiring diagram ................................... LT-122
H/LAMP - Wiring diagram .................................. LT-42
Harness connector ............................................ PG-71
Harness layout .................................................. PG-42
Hazard warning lamp ....................................... LT-152
Headlamp aiming control ...................... LT-99, LT-122
Headlamp leveler - See Headlamp aiming control ........
LT-122
Headlining - See Roof trim .................................. EI-54
Heated oxygen sensor 1 ..... EC-143, EC-150, EC-301
Heated oxygen sensor 1 (bank 1) .... EC-486, EC-496,
EC-696

IDX-6
ALPHABETICAL INDEX
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (EM)(QR20DE) ............... EM-12
NVH troubleshooting (EM)(VQ23DE and VQ35DE) .....
EM-126
O
O2S1B1 - Wiring diagram .................. EC-488
, EC-498
O2S1B2 - Wiring diagram .................. EC-490, EC-500
Oil cooler (engine)(VQ23DE and VQ35DE) ....... LU-23
Oil filter(QR20DE) .............................................. LU-10
Oil filter(VQ23DE and VQ35DE) ........................ LU-22
Oil pan (engine)(QR20DE) ............................... EM-26
Oil pan (engine)(VQ23DE and VQ35DE) ....... EM-145
Oil pressure (engine)(QR20DE) .......................... LU-7
Oil pressure (engine)(VQ23DE and VQ35DE) .. LU-20
Oil pump (engine)(QR20DE) ............................. LU-11
Oil pump (engine)(VQ23DE and VQ35DE) ....... LU-25
Oil pump regulator valve (engine)(QR20DE) ..... LU-11
Oil pump regulator valve (engine)(VQ23DE and
VQ35DE) ........................................................... LU-25
Oil seal replacement (engine)(QR20DE) ......... EM-53,
EM-62
, EM-70, EM-81
Oil seal replacement (engine)(VQ23DE and VQ35DE)
EM-207
On board diagnostic system ................ EC-33, EC-373
Out side mirror .................................... GW-74, GW-77
Overheat ............................................ EC-218, EC-575
Oversize piston(QR20DE) .............................. EM-103
Oversize piston(VQ23DE and VQ35DE) ........ EM-249
OVRCSV - Wiring diagram .............................. AT-101
P
Park/Neutral position switch .............. EC-238
, EC-614
Park/neutral position switch (A/T) ...... AT-161, AT-210
Park/neutral position switch (CVT) .................. CVT-62
PCV (positive crankcase ventilation) ... EC-30, EC-370
PHASE - Wiring diagram ................................. EC-178
PHSB1 - Wiring diagram .................................. EC-526
PHSB2 - Wiring diagram .................................. EC-528
Pilot bushing replacement - See Pilot
converter(QR20DE) .......................................... EM-81
Pilot bushing replacement - See Pilot
converter(VQ23DE and VQ35DE) .................. EM-228
Piston assembly(QR20DE) ............................... EM-92
Piston assembly(VQ23DE and VQ35DE) ....... EM-240
Piston pin inspection(QR20DE) ........................ EM-99
Piston pin inspection(VQ23DE and VQ35DE) EM-245
Piston ring inspection(QR20DE) ..................... EM-100
Piston ring inspection(VQ23DE and VQ35DE) EM-246
Piston to bore clearance(QR20DE) ................ EM-103
Piston to bore clearance(VQ23DE and VQ35DE) ........
EM-249
PNP/SW - Wiring diagram .. EC-239, EC-615, CVT-64
POS - Wiring diagram ........................ EC-171, EC-519
POWER - Wiring diagram ................... CVT-135, PG-4
Power door mirror .............................................. BL-21
Power seat ......................................................... SE-59
Power steering fluid level .................................. MA-42
Power steering gear ........................................... PS-17
Power steering oil pump .................................... PS-29
Power steering pressure (PSP) sensor .......... EC-185,
EC-533
Power supply routing .......................................... PG-3
Power window .................................................. GW-17
Precations for Leak detection dye .................. ATC-14
Precautions (General) ........................................... GI-4
Pressure control solenoid valve A .. CVT-97, CVT-102
Pressure control solenoid valve B CVT-105, CVT-108
Pressure test (CVT) ........................................ CVT-33
PRGVLV - Wirng diagram ................. EC-283, EC-678
Primary pressure sensor ............................... CVT-126
Primary Speed Sensor .................................... CVT-74
PRIPS - Wiring diagram ................................ CVT-127
PRSCVT - Wiring diagram .............................. CVT-75
PS/SEN - Wiring diagram ................. EC-186, EC-534
PT/SEN - Wiring diagram ................................ AT-121
R
R/FOG - Wiring diagram .................................. LT-144
Radiator(QR20DE) ............................... CO-13, CO-16
Radiator(VQ23DE and VQ35DE) ..................... CO-37
Radio - See Audio .................................... AV-4, AV-18
Rear bumper ....................................................... EI-17
Rear disc brake .................................................. BR-33
Rear door ............................................ BL-119, GW-50
Rear parcel shelf finisher .................................... EI-43
Rear seat ......................................................... SE-112
Rear window defogger ..................................... GW-54
Refrigerant connection precaution .................... ATC-6
Refrigerant discharging evacuating charging ATC-131
Refrigerant general precaution ......................... ATC-6
Refrigerant lines ............................................ ATC-131
Refrigerant pressure sensor EC-339, EC-748, ATC-83,
ATC-144
Refrigeration cycle .......................................... ATC-19
Removal and installation (A/T) ......................... AT-241
Road test ......... AT-48, AT-50, AT-51, AT-52, CVT-35
Rocker cover(QR20DE) .................................... EM-39
Rocker cover(VQ23DE and VQ35DE) ............ EM-160
Room lamp - See Interior lamp ........................ LT-219
ROOM/L - Wiring diagram ............................... LT-225
RP/SEN - Wiring diagram ................. EC-340, EC-749
RRO2 - Wiring diagram .................... EC-314, EC-320
RRO2B1 - Wiring diagram ................ EC-715, EC-724
RRO2B2 - Wiring diagram ................ EC-717, EC-726
S
SEAT - Wiring diagram ...................................... SE-59
Seat belt pre-tensioner disposal ..................... SRS-48
Seat belt, front ..................................................... SB-3
Seat, rear ......................................................... SE-112
Secondary pressure sensor .......................... CVT-118
Secondary Speed Sensor ............................... CVT-79
SECPS - Wiring diagram .............................. CVT-119

LU-1
ENGINE LUBRICATION SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION LU
A
LU

ENGINE LUBRICATION SYSTEM
QR
PRECAUTIONS .......................................................... 3
Precautions for Liquid Gasket .................................. 3
LIQUID GASKET APPLICATION PROCEDURE ..... 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
LUBRICATION SYSTEM ............................................ 5
Lubrication Circuit .................................................... 5
System Chart ........................................................... 6
ENGINE OIL ............................................................... 7
Inspection ................................................................. 7
ENGINE OIL LEVEL ............................................. 7
ENGINE OIL APPEARANCE ................................ 7
ENGINE OIL LEAKAGE ........................................ 7
OIL PRESSURE CHECK ...................................... 7
Changing Engine Oil ................................................ 9
OIL FILTER ............................................................... 10
Removal and Installation ........................................ 10
REMOVAL ........................................................... 10
INSTALLATION ................................................... 10
INSPECTION AFTER INSTALLATION ............... 10
OIL PUMP ..................................................................11
Removal and Installation ......................................... 11
REMOVAL ............................................................ 11
INSTALLATION .................................................... 11
INSPECTION AFTER INSTALLATION ................ 11
Disassembly and Assembly .................................... 11
DISASSEMBLY .................................................... 11
INSPECTION AFTER DISASSEMBLY ............... 12
ASSEMBLY ......................................................... 13
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 14
Standard and Limit ................................................. 14
OIL PRESSURE .................................................. 14
ENGINE OIL CAPACITY (APPROXIMATE) ........ 14
OIL PUMP ........................................................... 14
REGULATOR VALVE .......................................... 14
VQ
PRECAUTIONS ........................................................ 15
Precautions for Liquid Gasket ................................ 15
LIQUID GASKET APPLICATION PROCEDURE ... 15
PREPARATION ......................................................... 16
Special Service Tools ............................................. 16
Commercial Service Tools ...................................... 16
LUBRICATION SYSTEM .......................................... 17
Lubrication Circuit ................................................... 17
System Chart .......................................................... 18
ENGINE OIL .............................................................. 19
Inspection ............................................................... 19
ENGINE OIL LEVEL ............................................ 19
ENGINE OIL APPEARANCE .............................. 19
ENGINE OIL LEAKAGE ...................................... 19
OIL PRESSURE CHECK .................................... 20
Changing Engine Oil ............................................... 21
OIL FILTER ............................................................... 22
Removal and Installation ........................................ 22
REMOVAL ........................................................... 22
INSTALLATION ................................................... 22
INSPECTION AFTER INSTALLATION ................ 22
OIL COOLER (VQ35DE) ........................................... 23
Removal and Installation ........................................ 23
REMOVAL ........................................................... 23
INSPECTION AFTER REMOVAL ....................... 24
INSTALLATION ................................................... 24
INSPECTION AFTER INSTALLATION ................ 24
OIL PUMP ................................................................. 25
Removal and Installation ........................................ 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
INSPECTION AFTER INSTALLATION ................ 25
Disassembly and Assembly .................................... 25
DISASSEMBLY ................................................... 25
INSPECTION AFTER DISASSEMBLY ................ 26
ASSEMBLY ......................................................... 27

LU-4
[QR]
PREPARATION

PREPARATIONPFP:00002
Special Service ToolsBBS0059L
Commercial Service ToolsBBS0059M
Tool number
Tool nameDescription
ST25051001
Oil pressure gaugeMeasuring oil pressure
Maximum measuring range: 2,452 kPa
(24.52 bar, 25 kg/cm
2 , 356 psi)
ST25052000
HoseAdapting oil pressure gauge to cylinder block
KV10115801
Oil filter wrenchRemoving and installing oil filter
a: 64.3 mm (2.531 in)
WS39930000
Tube presserPressing the tube of liquid gasket
S-NT050
S-NT559
S-NT375
S-NT052
Tool nameDescription
Deep socketRemoving and installing oil pressure switch
a: 26 mm (1.02 in)
PBIC2072E