2003 NISSAN TEANA ignition

INTELLIGENT KEY SYSTEM
BL-75
C
D
E
F
G
H
J
K
L
MA
B
BL

Warning Procedure
List of Operation Related Parts
Parts marked with × are the parts related to operation.
Warning and alarm namesBuzzer Warning lamp
Inside car Outside car “KEY”
Ignition switch return forgotten warn-
ingBuzzer: Continuous — —
Ignition key warning
(When mechanical key used)Buzzer: Continuous — —
Ignition switch OFF position warning
(for inside car: when door closed)Buzzer: Twice — —
Ignition switch OFF position warning
(for outside car: when door opened/
closed)— Buzzer (3 times) —
Warning for removal of Intelligent Key
to outside the car (when door open/
closed)— Buzzer (3 seconds) Red illuminate
Warning for removal of Intelligent Key
to outside the car (from window)Buzzer (3 seconds) — Red illuminate
Door lock non-operation warning — Buzzer (2 seconds) —
Intelligent Key low battery pre-warning — —Green illuminate
(30 seconds after ignition switch
comes ON)
Warning and alarm functions
Intelligent Key
Key switch
Ignition knob switch
Intelligent Key unit ignition switch ACC position input signal
Intelligent Key unit ignition switch ON position input signal
Door switch
Door request switch
Door lock actuator
Inside key antenna
Outside key antenna (Driver, Passenger)
Outside key antenna (rear bumper)
Intelligent Key warning buzzer
Intelligent Key unit
CAN communication system
BCM
Combination meter
Ignition knob return forgotten warning (When Intelli-
gent Key used)××× ××××
Ignition key warning
(When mechanical key used)××× ××××
Ignition knob OFF position warning
(for outside car: when door closed)××× × ××××
Ignition knob OFF position warning
(for outside car: when door opened/closed)× ××× × ××××
Warning or take out of Intelligent Key to outside the
car
(when door open/closed)× × × × ×××××
Warning for take out of Intelligent Key to outside the
car (from window)× × × × ×××××

BL-76
INTELLIGENT KEY SYSTEM

CHANGE SETTINGS FUNCTION
The settings for each function can be changed with the CONSULT-II or Intelligent Key operation.
Changing Settings With the Intelligent Key
Intelligent Key remote controller button and door request switch operations change the engine startup function
settings (startup enabled/disabled) for each Intelligent Key independently.
Settings Change Procedure
1. With the ignition switch is in the LOCK position (ignition knob not pressed), hold down both the LOCK and
UNLOCK remote control buttons on the Intelligent Key at the same time for at least 10 seconds (The yard-
stick is that the Intelligent Key LED flashes 20 times.)
2. Within 5 seconds of releasing the Intelligent Key remote controller buttons, press the driver door request
switch.
3. The KEY warning lamp in combination meter lights up for 3 seconds (engine starting enabled → starting
disabled: lights up red, engine starting disabled → flashes green). This completes the settings change.
Changing Settings Using CONSULT-II
The settings for the Intelligent Key system functions can be changed using CONSULT-II (WORK SUPPORT).
Refer to BL-94, "
WORK SUPPORT" .
NOTE:
Once a function setting is changed, it will remain effective even if the battery is disconnected.
INTELLIGENT KEY REGISTRATION
Intelligent Key-ID registration is performed using the CONSULT-II. Up to 4 can be registered.
CAUTION:

After a new Intelligent Key-ID is registered, be sure to check the function.

When registering an additional Intelligent Key-ID, take any Intelligent Keys already registered and
Intelligent Keys for any other vehicles out of the vehicle before starting.
CONSULT-II can be used to check and delete Intelligent Key-IDs.
For future information, see the CONSULT-II Operation Manual NATS.
Door lock non-operation warning× × ××××××××××
Intelligent Key low battery warning×××××× Warning and alarm functions
Intelligent Key
Key switch
Ignition knob switch
Intelligent Key unit ignition switch ACC position input signal
Intelligent Key unit ignition switch ON position input signal
Door switch
Door request switch
Door lock actuator
Inside key antenna
Outside key antenna (Driver, Passenger)
Outside key antenna (rear bumper)
Intelligent Key warning buzzer
Intelligent Key unit
CAN communication system
BCM
Combination meter

INTELLIGENT KEY SYSTEM
BL-77
C
D
E
F
G
H
J
K
L
MA
B
BL

STEERING LOCK UNIT REGISTRATION
Steering Lock Unit ID Registration
CAUTION:

The method for registering a steering lock unit ID depends on the status of the steering lock unit
and Intelligent Key unit (new or old unit).

After registration is completed, press ignition knob with a portable unit in the vehicle so that it can
be rotated, and confirm that it cannot be rotated even when ignition switch is pressed without a
portable unit in the vehicle.
For future information, see the CONSULT-II Operation Manual NATS.
CAN Communication System DescriptionBIS000X0
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBIS000X1
Refer to LAN-49, "CAN System Specification Chart" .

BL-88
INTELLIGENT KEY SYSTEM

Terminals and Reference Value for Intelligent Key UnitBIS000X4
Te r m i -
nalWire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation or Conditions
1L/YSteering lock unit
power supplyOutput LOCK — 5
2 L CAN-HInput/
Output—— —
3 P CAN-LInput/
Output—— —
4SBIntelligent Key warn-
ing buzzer (driver
side/trunk room)Output LOCKAny door open and
operate remote
controller button or
door request
switch.Buzzer
OFFBattery voltage
Sound
buzzer0
5B/WDoor request switch
(driver side)Input LOCKDoor request switch operation:
Press (ON).0
Other than the above (OFF) 5
6 G Ignition switch (ON) Input ON — Battery voltage
7 B/R key switch Input LOCKInsert mechanical key into igni-
tion key cylinder.Battery voltage
Remove mechanical key from
ignition key cylinder.0
11 Y/B Power source (Fuse) Input LOCK — Battery voltage
12 B Ground — ON — 0
13 V/WInside key antenna
(+)
(Trunk room)
Output LOCKAny door open → Close
(Door switch: ON → OFF)
14 W/LInside key antenna (-)
(Trunk room)
15 R/YInside key antenna
(+) signal
(Center console)
Output LOCKAny door open → Close (Door
switch: ON → OFF)
Ignition knob switch: ON (press
ignition knob.)
16 R/GInside key antenna (-)
signal
(Center console)
17 W/ROutside key antenna
(Rear bumper) (+)
Output LOCKTrunk opener request switch
operation (Switch: ON)
18 W/BOutside key antenna
(Rear bumper) (-)
19 POutside key antenna
(driver side) (+)
Output LOCKDriver door request signal opera-
tion (Switch: ON)
20 OOutside key antenna
(driver side) (-)
SIIA1910J
SIIA1910J
SIIA1910J
SIIA1910J

INTELLIGENT KEY SYSTEM
BL-89
C
D
E
F
G
H
J
K
L
MA
B
BL

25 P/LDoor request switch
(passenger side)Input LOCKDoor request switch operation:
Press (ON)0
Other than the above (OFF) 5
27 BR Ignition knob switch Input —Press ignition knob. Battery voltage
Return ignition knob to LOCK
position.0
28 LG/RDoor unlock sensor
(driver side)Input LOCK Driver side doorLocked 5
Other than
above0
29 G/OTrunk opener request
switchInput LOCKTrunk opener request switch
operation: Press (ON)0
Other than the above (OFF) 5
31 G/YSteering lock unit
ground—ON — 0
32 L/RSteering lock unit
communicationInput/
OutputLOCKPress ignition knob with Intelli-
gent Key inside vehicle.
Other than the above 5
33 L/WInside key antenna
(+) signal
(Instrument center
lower)
Output LOCKAny door open → Close (Door
switch: ON → OFF)
Ignition knob switch: ON (press
ignition knob.)
34 R/WInside key antenna (-)
signal
(Instrument center
lower)
37 GROutside key antenna
(passenger side) (+)
Output LOCKPassenger door request switch
operation (Switch: ON)
38 LGOutside key antenna
(passenger side) (-) Te r m i -
nalWire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation or Conditions
PIIB8449J
SIIA1910J
SIIA1910J

BL-90
INTELLIGENT KEY SYSTEM

Terminals and Reference Value for Steering Lock UnitBIS000X5
Terminals and Reference Value for BCMBIS000X6
Te r m i -
nalWire
ColorSignal DesignationSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation or Conditions
1 Y/B Battery power supply Input LOCK — Battery voltage
2L/YSteering lock unit power
supplyOutput LOCK — 5
3L/RSteering lock unit com-
munication signalInput/
OutputLOCKPress ignition knob with
Intelligent Key inside
vehicle.
Other than the above 5
4G/YSteering lock unit
ground—ON — 0
PIIB8449J
Te r m i -
nalWire
ColorItemSignal
Input/
OutputConditionVoltage (V)
(Approx.)
12 R/LFront door switch (Passenger
side)Input Door open (ON) → Close (OFF) 0 → Battery voltage
13 R/B Rear door switch RH Input Door open (ON) → Close (OFF) 0 → Battery voltage
38 R Ignition switch InputIgnition switch is in ON or START posi-
tionBattery voltage
39 L CAN-HInput/
Output——
40 P CAN-LInput/
Output——
42 Y/R Battery power supply (Fuse) Input — Battery voltage
52 B Ground — — 0
55 W/BBattery power supply (Fusible
link)Input — Battery voltage
57 V/W Trunk room lamp switch Input Trunk lid open (ON) → Close (OFF) 0 → Battery voltage
62 SB Front door switch (Driver side) Input Door open (ON) → Close (OFF) 0 → Battery voltage
63 R/W Rear door switch LH Input Door open (ON) → Close (OFF) 0 → Battery voltage

INTELLIGENT KEY SYSTEM
BL-93
C
D
E
F
G
H
J
K
L
MA
B
BL

CONSULT-II Functions (INTELLIGENT KEY)BIS001TD
CONSULT-II can display each diagnostic item using the diagnostic test modes as shown below.
CONSULT-II Inspection ProcedureBIS001TE
CAUTION:
If CONSULT-II is used with no connection CONSULT-II CONVERTER, malfunctions might be detected
in self-diagnosis depending on control unit which performs CAN Communication.
BASIC OPERATION
Refer to GI-34, "CONSULT-II Start Procedure" .
CONSULT-II Application ItemsBIS001TF
SELF-DIAGNOSTIC RESULTS
*: It is possible to display it only with the program card for engine immobilizer system.
DATA MONITOR
Part to be diagnosed Test item, Diagnosis mode Description
Intelligent KeyWORK SUPPORT Changes settings for each function.
SELF-DIAG RESULTS Intelligent Key unit performs CAN communication diagnosis.
DATA MONITOR Displays Intelligent Key unit input data in real time.
CAN DIAGNOSTIC SUPPORT
MONITORThe results of transmit/receive diagnosis of CAN Communication can
be read.
ACTIVE TESTOperation of electrical loads can be checked by sending driving signal
to then.
ECU PART NUMBER Displays Intelligent Key unit part No.
DTC Self-diag results Description Diagnosis procedureReference
page
U1000 CAN COMM CIRCUITMalfunction is detected in CAN communica-
tion.Check CAN communica-
tion system.BL-100
U1010 CONTROL UNIT (CAN) Intelligent Key unit internal malfunctionCheck CAN communica-
tion system.BL-100
B2013*STRG COMM CIRCUITMalfunction is detected in communication of
Intelligent Key unit and steering lock unit.Check steering lock unit.BL-115
B2552*INTELLIGENT KEY Intelligent Key unit internal malfunctionReplace Intelligent Key
unit.BL-117
B2590*DISCORD BCM - I-KEY Malfunction is detected in immobilizer system. Check NATS.BL-139
Monitor item Content
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
KEY SW Indicates [ON/OFF] condition of key switch.
DR REQ SW Indicates [ON/OFF] condition of door request switch (driver side).
AS REQ SW Indicates [ON/OFF] condition of door request switch (passenger side).
BD/TR REQ SW Indicates [ON/OFF] condition of trunk opener request switch.
IGN SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC SW Indicates [ON/OFF] condition of ignition switch in ACC position.
DOOR STAT SW Indicates [ON/OFF] condition of stop lamp switch.
STOP LAMP SW Indicates [ON/OFF] condition of door unlock sensor.
P RANGE SW* Indicates [ON/OFF] condition of park position switch.
DOOR LOCK SIG* Indicates [ON/OFF] condition of door lock signal from Intelligent Key remote controller button.
DOOR UNLOCK SIG* Indicates [ON/OFF] condition of door unlock signal from Intelligent Key remote controller button.
KEYLESS TRUNK* Indicates [ON/OFF] condition of trunk open signal from Intelligent Key remote controller button.

INTELLIGENT KEY SYSTEM
BL-95
C
D
E
F
G
H
J
K
L
MA
B
BL

ACTIVE TEST
ENGINE START BY I-KEYEngine start function mode can be changed to operate (ON) or not operate (OFF) with this mode.
The operation mode will be changed when “CHANGE SETT” on CONSULT-II screen is touched.
LOCK/UNLOCK BY I-KEYDoor lock/unlock function by door request switch (driver side, passenger side and trunk) mode
can be changed to operate (ON) or not operate (OFF) with this mode. The operation mode will be
changed when “CHANGE SETT” on CONSULT-II screen is touched. Monitor item Description
Test item Description
DOOR LOCK/UNLOCKThis test is able to check door lock/unlock operation.

The all door lock actuators are unlocked and hazard warning lamps flash twice when “ALL
UNLK” on CONSULT-II screen is touched.

The all door lock actuators are locked and hazard warning lamps flash once when “LOCK” on
CONSULT-II screen is touched.
ANTENNAThis test is able to check Intelligent Key antenna operation.
When the following conditions are met, hazard warning lamps flash.

Inside key antenna (Instrument center lower) detects Intelligent Key, when “RM ANT1” on
CONSULT-II screen is touched.

Inside key antenna (Center console) detects Intelligent Key, when “RM ANT2” on CONSULT-II
screen is touched.

Inside key antenna (Trunk room) detects Intelligent Key, when “LAG ANT” on CONSULT-II
screen is touched.

Outside key antenna (Driver side) detects Intelligent Key, when “DR ANT” on CONSULT-II
screen is touched.

Outside key antenna (Passenger side) detects Intelligent Key, when “AS ANT” on CONSULT-II
screen is touched.

Outside key antenna (Rear bumper) detects Intelligent Key, when “BD ANT” on CONSULT-II
screen is touched.
OUTSIDE BUZZERThis test is able to check Intelligent Key warning buzzer (driver side/ trunk room) operation.
Intelligent Key warning buzzer (driver side/ trunk room) sounds when “ON” on CONSULT-II
screen is touched.
INSIDE BUZZERThis test is able to check Intelligent Key warning buzzer (combination meter) operation.

Take away warning chime sounds when “TAKE OUT” on CONSULT-II screen is touched.

Ignition switch warning chime sounds when “KNOB” on CONSULT-II screen is touched.

Ignition key warning chime sounds when “KEY” on CONSULT-II screen is touched.
INDICATORThis test is able to check warning lamp operation.

“KEY” Warning lamp (Green) illuminates when “BLUE ON” on CONSULT-II screen is touched.

“KEY” Warning lamp (Red) illuminates when “RED ON” on CONSULT-II screen is touched.

“LOCK” Warning lamp illuminates when “KNOB ON” on CONSULT-II screen is touched.

“KEY” Warning lamp (Green) flashes when “BLUE IND” on CONSULT-II screen is touched.

“KEY” Warning lamp (RED) flashes when “BLUE IND” on CONSULT-II screen is touched.

“LOCK” Warning lamp flashes when “KNOB ON” on CONSULT-II screen is touched.