2003 NISSAN TEANA Power

BL-112
INTELLIGENT KEY SYSTEM

3. CHECK INTELLIGENT KEY WARNING BUZZER OPERATION
Connect battery power supply to Intelligent Key warning buzzer connector D22 (driver side), B222 (trunk
room) terminals 1 and 2, and check the operation.
OK or NG
OK >> Intelligent Key warning buzzer is OK.
NG >> Replace Intelligent Key warning buzzer
Check Outside Key AntennaBIS000XL
1. CHECK OUTSIDE KEY ANTENNA POWER SUPPLY-1
Push each door request switch, and use an oscilloscope to check voltage waveform of harness between Intel-
ligent Key unit connector M31 terminals 17 (rear bumper), 19 (driver door), and 37 (passenger door) and
ground.
OK or NG
OK >> Outside key antenna is OK.
NG >> GO TO 2.1 (BAT+) - 2 (BAT-) : the buzzer sounds
PIIA6750E
Push each door request switch.
Rear bumper:
17 (W/R) - Ground
Driver:
19 (P) - Ground
Passenger:
37 (GR) - Ground
MIIB0375E
SIIA1910J

INTELLIGENT KEY SYSTEM
BL-113
C
D
E
F
G
H
J
K
L
MA
B
BL

2. CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Disconnect Intelligent Key unit connector and outside key antenna connector.
2. Check continuity between each outside key antenna connector D25 (driver side), D43 (passenger side),
B31 (rear bumper) terminals 1, 2 and Intelligent Key unit connector M31 terminals 17, 18, 19, 20, 37, and
38.
3. Check continuity between each out side key antenna connector
terminals 1, 2 and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace harness between outside key antenna and
Intelligent Key unit.
3. CHECK OUTSIDE KEY ANTENNA POWER SUPPLY-2
1. Replace outside key antenna.
2. Push each door request switch, and use an oscilloscope to
check voltage wave form of harness between Intelligent key unit
connector M31 terminals 17 (rear bumper), 19 (driver door), and
37 (passenger door) and ground.
OK or NG
OK >> Outside key antenna is malfunctioning.
NG >> Replace Intelligent key unit.
Rear bumper1 (W/R) - 17 (W/R): Continuity should exist.
2 (W/B) - 18 (W/B): Continuity should exist.
Driver side1 (P) - 19 (P): Continuity should exist.
2 (O) - 20 (O): Continuity should exist.
Passenger side1 (GR) - 37 (GR): Continuity should exist.
2 (LG) - 38 (LG): Continuity should exist.
Rear bumper1 (W/R) - Ground: Continuity should not exist.
2 (W/B) - Ground: Continuity should not exist.
Driver side1 (P) - Ground: Continuity should not exist.
2 (O) - Ground: Continuity should not exist.
Passenger side1 (GR) - Ground: Continuity should not exist.
2 (LG) - Ground: Continuity should not exist.
PIIB0960E
Push each door request switch.
Rear bumper:
17 (W/R) - Ground
Driver:
19 (P) - Ground
Passenger:
37 (GR) - Ground
MIIB0375E
SIIA1910J

BL-114
INTELLIGENT KEY SYSTEM

Check Inside Key AntennaBIS000XM
1. CHECK INSIDE KEY ANTENNA POWER SUPPLY CIRCUIT-1
Push ignition knob and use an oscilloscope to check voltage waveform between Intelligent Key unit connector
M31 terminals 13 (trunk room), 15 (center console), 33 (instrument center lower) and ground.
OK or NG
OK >> Inside key antenna is OK.
NG >> GO TO 2.
2. CHECK INSIDE KEY ANTENNA
1. Disconnect Intelligent Key unit connector and inside key antenna connectors.
2. Check continuity between inside key antenna connector M68 (center console), M75 (instrument center
lower), B229 (trunk room) terminals 1, 2 and Intelligent Key unit connector M31 terminals 13, 14, 15, 16,
33 and 34.
3. Check continuity between inside key antenna connector M68
(center console), M75 (instrument center lower), B229 (trunk
room) terminals 1, 2 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between inside key antenna and Intelligent Key unit.
ConnectorTerminal
(Wire color)Signal (V)
(Approx.)
(+) (–)
M3113 (V/W)
Ground 15 (R/Y)
33 (L/W)
PIIB8799ESIIA1910J
Trunk room1 (V/W) - 13 (V/W): Continuity should exist.
2 (W/L) - 14 (W/L): Continuity should exist.
Center console1 (R/Y) - 15 (R/Y): Continuity should exist.
2 (R/G) - 16 (R/G): Continuity should exist.
Instrument center lower1 (R/W) - 33 (R/W): Continuity should exist.
2 (L/W) - 34 (L/W): Continuity should exist.
Trunk room1 (V/W) - Ground: Continuity should not exist.
2 (W/L) - Ground: Continuity should not exist.
Center console1 (R/Y) - Ground: Continuity should not exist.
2 (R/G) - Ground: Continuity should not exist.
Instrument center lower1 (R/W) - Ground: Continuity should not exist.
2 (L/W) - Ground: Continuity should not exist.
PIIB8800E

INTELLIGENT KEY SYSTEM
BL-115
C
D
E
F
G
H
J
K
L
MA
B
BL

3. CHECK INSIDE KEY ANTENNA POWER SUPPLY-2
1. Replace inside key antenna.
2. Push ignition knob, and use an oscilloscope to check voltage
wave form between Intelligent key unit connector M31 terminals
13 (trunk room), 15 (center console), and 33 (instrument center
lower) and ground.
OK or NG
OK >> Inside key antenna is malfunctioning.
NG >> Replace Intelligent key unit.
Check Steering Lock UnitBIS000XN
1. CHECK STEERING LOCK UNIT POWER SUPPLY
1. Turn ignition knob to LOCK position.
2. Disconnect steering lock unit connector.
3. Check voltage between steering lock unit connector M21 terminal 1 (Y/B) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace steering lock unit power supply circuit.
2. CHECK STEERING LOCK UNIT GROUND CIRCUIT
Check continuity between steering lock unit connector M21 terminal 4 (G/Y) and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
Push each door request switch.
Trunk room:
13 (V/W) - Ground
Center console:
15 (R/Y) - Ground
Instrument center lower:
33 (L/W) - Ground
PIIB8801E
SIIA1910J
1 (Y/B) - Ground : Battery voltage
PIIA6797E
4 (G/Y) - Ground : Continuity should exist.
PIIA6798E

BL-136
TRUNK LID OPENER

TRUNK LID OPENERPFP:84640
Component Parts and Harness Connector LocationBIS000Y6
System DescriptionBIS000Y7
Power is supplied at all times

through 50A fusible link (letter M, located in fuse and fusible link box)

to BCM terminal 55,

through 15A fuse [No.17, located in fuse block (J/B)]

to BCM terminal 42.
Ground is supplied

to BCM terminals 52

through body grounds M71 and M72.
When trunk lid opener switch is ON (pushed), ground is supplied

to BCM terminal 30

through trunk lid opener switch terminals 3 and 2, and

through body grounds M71 and M72.
And power is supplied

through BCM terminal 68

to trunk lid opener actuator terminal 2.
Ground is supplied

to trunk lid opener actuator terminal 1, and

through body grounds B214 and B217.
Then BCM unlocks trunk lid opener actuator.
TRUNK LID OPENER OPERATION
When trunk lid opener switch or trunk button of key fob is ON, trunk opener actuator unlocked by BCM.
BCM can unlock trunk lid opener actuator when

vehicle speed is less than 5 km/h (3MPH)
BCM does not unlock trunk lid opener actuator when

vehicle speed is more than 5 km/h (3MPH)
1. BCM M3,M4,M5 2. Trunk lid opener switch D9 3. Trunk lid lock assembly T7
(Trunk room lamp switch)
PIIB8753E

BL-138
TRUNK LID OPENER

Terminal and Reference Value for BCMBIS000Y9
CONSULT-II Function (BCM)BIS000YA
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II STRAT PROCEDURE
Refer toGI-34, "CONSULT-II Start Procedure" .
CONSULT-II APPLICATION ITEMS
Data Monitor
*: With Intelligent Key system
Active Test
Te r m i -
nalWire
colorItemSignal
Input/
OutputConditionVoltage(V)
(Approx.)
30 L/O Trunk lid opener switch Input Trunk lid opener switchON 0
OFF Battery voltage
42 Y/R Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
55 W/B Power source (Fusible link) Input — Battery voltage
57 V/W Trunk room lamp switch Input Trunk lidOPEN 0
CLOSE Battery voltage
68 R Trunk lid opener output signal Output Trunk lid opener switchON 0 → Battery voltage → 0
OFF 0
BCM diagnosis
partInspection item, Self-diagnosis
modeContent
Door lockDATA MONITOR Displays BCM input data on real-time basis.
ACTIVE TEST Sends drive signals to trunk lid opener actuator to perform operation check.
Monitor item Content
KEY ON SW Indicates [ON/OFF] condition of key switch.
KYLS TRNK/HAT Indicates [ON/OFF] condition of trunk open signal from key fob.
IKEY TRNK/HAT* Indicates [ON/OFF] condition of trunk open signal from Intelligent Key
TRNK OPNR SW Indicates [ON/OFF] condition of trunk lid open signal from trunk lid opener switch.
VEHICLE SPEED Indicates [km/h] condition of vehicle speed.
Test item Content
TRUNK/GLASS HATCHThis test is able to check trunk lid opener actuators unlock operation.
These actuators lock when “OPEN” on CONSULT-II screen is touched.

BL-146
NATS(NISSAN ANTI-THEFT SYSTEM)

Terminals and Reference Value for Steering Lock Unit/with Intelligent Key Sys-
tem
BIS000YG
Terminals and Reference Value for Intelligent Key Unit/with Intelligent Key Sys-
tem
BIS000YH
Te r -
minalWire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation Or Conditions
1Y/BBattery power sup-
plyInput LOCK — Battery voltage
2L/YSteering lock unit
power supplyInput LOCK — 5
3L/RSteering lock unit
communication sig-
nalInput/
OutputLOCKPress ignition knob with Intelli-
gent Key inside vehicle.
Other than the above 5
4G/YSteering lock unit
ground—ON — 0
PIIB8449J
Te r -
minalWire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation Or Conditions
1L/YSteering lock unit
power supplyOutput LOCK — 5
2 L CAN communication HInput/
Output—— —
3 P CAN communication LInput/
Output—— —
6 G Ignition power supply Input ON — Battery voltage
7 B/R Key switch Input LOCKInsert mechanical key into
ignition key cylinder.Battery voltage
Remove mechanical key from
ignition key cylinder.0
11 Y/B Battery power supply Input LOCK — Battery voltage
12 B Ground — ON — 0
27 BR Ignition knob switch Input —Press ignition knob. Battery voltage
Return ignition knob to LOCK
position.0
31 G/YSteering lock unit
ground—ON — 0
32 L/RSteering lock unit com-
munication signalInput/
OutputLOCKPress ignition knob with Intelli-
gent Key inside vehicle.
Other than the above 5
PIIB8449J

NATS(NISSAN ANTI-THEFT SYSTEM)
BL-147
C
D
E
F
G
H
J
K
L
MA
B
BL

Terminals and Reference Value for BCMBIS000YI
*: With Intelligent Key systemTe r -
minalWire
ColorItemSignal
Input/
OutputCondition
Voltage (V)
(Approx.) Ignition
Knob
PositionOperation Or Conditions
21 P/L NATS antenna amp. Output — Ignition knob OFF → ON positionShould move just after
turning ignition knob
“ON” pointer tester
23 L/B Security indicator lamp Output LOCKGoes OFF → illuminates (Every 2.4
seconds)Battery voltage → 0
25 LG NATS antenna amp.Input/
Output— Ignition knob OFF → ON positionShould move just after
turning ignition knob
“ON” pointer tester
37* B/R Key switch Input —Insert mechanical key into ignition key
cylinderBattery voltage
Remove mechanical key from ignition
key cylinder0
38 R Ignition power supply Input ON Ignition knob ON or START position Battery voltage
39 L CAN-HInput/
Output—— —
40 P CAN-LInput/
Output—— —
42 Y/R Battery power supply Input LOCK — Battery voltage
52 B Ground — ON — 0
55 W/B Battery power supply Input LOCK — Battery voltage