2003 NISSAN TEANA mirror

GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION GW
A
B
GW

GLASSES, WINDOW SYSTEM & MIRRORS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Handling for Adhesive and Primer ........................... 3
PREPARATION ........................................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
WINDSHIELD GLASS ...............................................11
Removal and Installation ......................................... 11
REMOVAL ............................................................ 11
INSTALLATION ................................................... 12
SIDE WINDOW GLASS ............................................ 13
Removal and Installation ........................................ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 14
REAR WINDOW GLASS AND MOLDING ............... 15
Removal and Installation ........................................ 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 16
POWER WINDOW SYSTEM .................................... 17
Component Parts and Harness Connector Location ... 17
System Description ................................................ 17MANUAL OPERATION ........................................ 18
POWER WINDOW LOCK ................................... 20
TIMER FUNCTION .............................................. 20
ANTI-PINCH SYSTEM ........................................ 21
Schematic ............................................................... 22
Wiring Diagram — WINDOW — ............................. 23
Terminal and Reference Value for BCM ................. 27
Terminal and Reference Value for Power Window
Main Switch ............................................................ 27
Work Flow ............................................................... 28
Trouble Diagnosis Symptom Chart ......................... 29
Check BCM Power Supply and Ground Circuit ...... 30
Check Power Window Main Switch Power Supply
and Ground Circuit ................................................. 30
Check Front Power Window Motor (Driver Side) Cir-
cuit .......................................................................... 32
Check Front Power Window Motor (Passenger
Side) Circuit ............................................................ 33
Check Rear Power Window Motor RH Circuit ........ 35
Check Rear Power Window Motor LH Circuit ......... 37
Check Limit Switch Circuit (Driver Side) ................. 40
Check Encoder Circuit (Driver Side) ....................... 42
Check Door Switch ................................................. 44
Check Power Window Lock Switch ........................ 45
FRONT DOOR GLASS AND REGULATOR ............. 46
Removal and Installation ........................................ 46
DOOR GLASS ..................................................... 46
REGULATOR ASSEMBLY .................................. 47
Disassembly and Assembly .................................... 48
REGULATOR ASSEMBLY .................................. 48
Inspection after Installation ..................................... 49
SETTING OF LIMIT SWITCH (DRIVER SIDE) ... 49
FITTING INSPECTION ....................................... 49
REAR DOOR GLASS AND REGULATOR ............... 50
Removal and Installation ........................................ 50
DOOR GLASS ..................................................... 50
REGULATOR ASSEMBLY .................................. 52
Inspection after Installation ..................................... 53
FITTING INSPECTION ....................................... 53
REAR WINDOW DEFOGGER .................................. 54

GW-2 Component Parts and Harness Connector Location ... 54
System Description ................................................. 54
CAN Communication System Description .............. 56
CAN Communication Unit ....................................... 56
Schematic ............................................................... 57
Wiring Diagram — DEF — ..................................... 58
Terminal and Reference Value for BCM ................. 62
Terminal and Reference Value for IPDM E/R ......... 62
Work Flow ............................................................... 62
CONSULT-II Function (BCM) .................................. 63
CONSULT-II Start procedure .................................. 63
CONSULT-II Application Items ............................... 63
DATA MONITOR .................................................. 63
ACTIVE TEST ..................................................... 63
Trouble Diagnoses Symptom Chart ........................ 63
Check BCM Power Supply and Ground Circuit ...... 64
Check Rear Window Defogger Switch Circuit ........ 65
Check Rear Window Defogger Power Supply Cir-
cuit .......................................................................... 66
Check Rear Window Defogger Circuit .................... 67
Check Door Mirror Defogger Power Supply Circuit ... 68
Check Driver Side Door Mirror Defogger Circuit ..... 70Check Passenger Side Door Mirror Defogger Circuit
... 71
Check Filament ....................................................... 72
Filament Repair ....................................................... 72
REPAIR EQUIPMENT ......................................... 72
REPAIRING PROCEDURE ................................. 73
DOOR MIRROR ......................................................... 74
Precautions to Handle Retractable Power Door Mir-
rors .......................................................................... 74
Door Mirror .............................................................. 75
WIRING DIAGRAM — MIRROR — .................... 75
Removal and Installation ......................................... 77
REMOVAL ............................................................ 77
INSTALLATION .................................................... 77
Disassembly and Assembly .................................... 78
DISASSEMBLY .................................................... 78
ASSEMBLY .......................................................... 79
INSIDE MIRROR ....................................................... 80
Removal and Installation ......................................... 80
REMOVAL ............................................................ 80
INSTALLATION .................................................... 80

REAR WINDOW DEFOGGER
GW-55
C
D
E
F
G
H
J
K
L
MA
B
GW


through 15A fuse [No. 17, located in the fuse block (J/B)]

to BCM terminal 42.
With the ignition switch turned to ON or START position,
Power is supplied

through 10A fuse [No. 1, located in the fuse block (J/B)]

to BCM terminal 38.

through 10A fuse [No.12, located in the fuse block (J/B)]

to rear window defogger relay terminal 1.

through 10A fuse [No. 6, located in the fuse block (J/B)]

to A/C and AV switch terminal 7.
Ground is supplied

to BCM terminal 52

through grounds M71 and M72.

to A/C and AV switch terminal 13

through grounds M71 and M72.

to IPDM E/R terminals 38 and 60

through grounds E1 and E31.
When rear window defogger switch in A/C and AV switch is turned to ON,
Ground is supplied

to BCM terminal 9

through A/C and AV switch terminal 9

through A/C and AV switch terminal 13

through grounds M71 and M72.
Then rear window defogger switch is illuminated.
Then BCM recognizes that rear window defogger switch is turned to ON.
Then it sends rear window defogger switch signals to IPDM E/R and display unit (with out display control unit)
or display control unit (with display control unit) via DATA LINE (CAN H, CAN L).
When display unit or display control unit receives rear window defogger switch signals, indicator is displayed
on the screen.
When IPDM E/R receives rear window defogger switch signals,
Ground is supplied

to rear window defogger relay terminal 2

through IPDM E/R terminal 52

through IPDM E/R terminal 38 and 60

through grounds E1 and E31.
and then rear window defogger relay is activated.
When rear window defogger relay is turned ON,
Signals are transmitted,

through rear window defogger relay terminals 5

to rear window defogger terminal 1.
Rear window defogger terminal 2 is grounded through ground B253.
With power and ground supplied, rear window defogger filaments heat and defog the rear window.

through rear window defogger relay terminals 7

to door mirror defogger (driver side and passenger side) terminal 2.
Door mirror defogger (driver side and passenger side) terminal 3 are grounded through grounds M71 and
M72.
With power and ground supplied, door mirror defogger filaments heat and defog the mirror.

REAR WINDOW DEFOGGER
GW-63
C
D
E
F
G
H
J
K
L
MA
B
GW

CONSULT-II Function (BCM)BIS00105
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II Start procedureBIS0016N
Refer to GI-34, "CONSULT-II Start Procedure"
CONSULT-II Application ItemsBIS0016O
DATA MONITOR
Display Item List
ACTIVE TEST
Display Item List
Trouble Diagnoses Symptom ChartBIS00106
Check that other systems using the signal of the following systems operate normally.
BCM diagnostic test itemCheck item,
diagnostic test modeContent
Rear defoggerData monitor Displays the input data of BCM in real time.
Active test Gives a drive signal to a load to check the operation.
Monitor item Content
IGN ON SW indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW indicates [ON/OFF] condition of ignition switch in ACC position.
REAR DEF SW indicates [ON/OFF] condition of rear window defogger switch.
Test item Content
REAR DEFOGGER This test is able to check rear window defogger operation.
Symptom Diagnoses / service procedureReference
page
Rear window defogger and door mirror defogger do not
operate.1. Check BCM power supply and ground circuit.GW-64
2.Check IPDM E/R auto active test.PG-21
3. Check rear window defogger switch circuit.GW-65
4. Check rear window defogger power supply circuit.GW-66
5. Replace IPDM E/R.PG-28
Rear window defogger does not operated.1. Check BCM power supply and ground circuit.GW-64
2. Check IPDM E/R auto active test.PG-21
3.Check rear window defogger switch circuit.GW-65
4. Check rear window defogger power supply circuit.GW-66
5. Check rear window defogger circuit.GW-67
6. Check filament.GW-72
7. Replace IPDM E/R.PG-28
Rear window defogger does not operate but door mirror
defoggers operate.1. Check rear window defogger circuit.GW-67
2. Check filament.GW-72
Both of door mirror defoggers do not operated but rear
window defogger operate.1. Check door mirror defogger power supply circuit.GW-68
Driver side door mirror defogger does not operated. 1. Check driver side door mirror defogger circuit.GW-70
Passenger side door mirror defogger does not operated. 1. Check passenger side door mirror defogger circuit.GW-71

GW-68
REAR WINDOW DEFOGGER

2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between rear window defogger connector
B252 terminal 2 and ground.
OK or NG
OK >> Check filament. Refer to GW-72, "Check Filament"

If filament is OK, check condition of harness and con-
nector.

If filament is NG, repair filament.
NG >> Repair or replace harness.
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect rear window defogger relay connector and condenser connector.
3. Check continuity between rear window defogger relay connector
B203 terminal 5 and condenser connector B216 terminal 1.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK HARNESS CONTINUITY 2
1. Check continuity between condenser connector B216 terminal 1
and rear window defogger connector B251 terminal 1.
2. Check continuity between condenser connector B216 terminal 1
and ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace condenser.
Check Door Mirror Defogger Power Supply Circuit BIS0010B
1. CHECK FUSE

Check 10A fuse [No.32, located in fuse block (J/B)]
NOTE:
Refer to GW-54, "
Component Parts and Harness Connector Location"
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3, "POWER SUPPLY ROUTING CIRCUIT"
2 (B) − Ground : Continuity should exist.
PIIA4235E
5 (G) – 1 (G) : Continuity should exist.
PIIB1100E
1 (G) – 1 (B) : Continuity should exist.
1 (G) – Ground : Continuity should not exist.
PIIB1101E

REAR WINDOW DEFOGGER
GW-69
C
D
E
F
G
H
J
K
L
MA
B
GW

2. CHECH REAR WINDOW DOFOGGER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Remove rear window defogger relay.
3. Turn ignition switch ON.
4. Check voltage between rear window defogger relay harness
connector B203 terminal 6 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK REAR WINDOW DEFOGGER RELAY
Check continuity between rear window defogger relay terminal 6 and 7.
OK or NG
OK >> GO TO 4.
NG >> Replace rear window defogger relay.
4. CHECK HARENSS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect door mirror connector.
3. Check continuity between door mirror D3 (driver side), D33
(passenger side) terminal 2 and rear window defogger relay
connector B203 terminal 7.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Repair or replace harness.6 (W) - Ground : Battery voltage
PIIA9561E
Terminal Condition Continuity
6712V direct current supply
between terminals 1 and 2Ye s
No current supply No
SEC202B
2 (L/B) - 7 (L/B) : Continuity should exist.
PIIB2181E

GW-70
REAR WINDOW DEFOGGER

Check Driver Side Door Mirror Defogger Circuit BIS0010C
1. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror (driver side) connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror (driver side) connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror (driver side) connector D3
terminal 3 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR MIRROR DEFOGGER
Check continuity between door mirror (driver side) terminal 2 and 3.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Replace door mirror (driver side).
ConnectorTerminal (Wire color)
Condition of rear win-
dow defogger switchVoltage (V)
(Approx.)
(+) (–)
D3 2 (L/B) GroundON Battery voltage
OFF 0
PIIB2182E
3 (B) – Ground : Continuity should exist.
PIIB2183E
2 – 3 : Continuity should exist.
PIIB2184E

REAR WINDOW DEFOGGER
GW-71
C
D
E
F
G
H
J
K
L
MA
B
GW

Check Passenger Side Door Mirror Defogger Circuit BIS0010D
1. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror (passenger side) connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror (passenger side) connector
and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror (passenger side) connec-
tor D33 terminal 3 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR MIRROR DEFOGGER
Check continuity between door mirror (passenger side) terminal 2
and 3.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Replace door mirror (passenger side).
ConnectorTerminal (Wire color)
Condition of rear win-
dow defogger switchVoltage (V)
(Approx.)
(+) (–)
D33 2 (L/B) GroundPress Battery voltage
OFF 0
PIIB2182E
3 (B) – Ground : Continuity should exist.
PIIB2183E
2 – 3 : Continuity should exist.
PIIB2184E