2003 NISSAN ALMERA N16 transmission

DISASSEMBLY
AT-427
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
35. Remove rear planetary carrier assembly and rear sun gear
according to the following procedures.
a. Remove rear planetary carrier assembly from transmission
case.
b. Remove rear sun gear from rear planetary carrier.
c. Remove needle bearings from rear planetary carrier assembly.
d. Check rear planetary carrier, rear sun gear and needle bearings
for damage or wear.
e. Check clearance between pinion washer and rear planetary car-
rier with feeler gauge.
Replace rear planetary carrier if the clearance exceeds allow-
able limit.
36. Remove rear internal gear from transmission case.
SAT051D
SAT052D
SAT053D
Standard clearance: 0.15 - 0.70 mm (0.0059 - 0.0276 in)
Allowable limit: 0.80 mm (0.0315 in)
SAT054D
SAT055D

AT-428
[ALL]
DISASSEMBLY
37. Remove needle bearing from rear internal gear.
●Check needle bearing for damage or wear.
38. Remove forward clutch assembly from transmission case.
39. Remove thrust washer from transmission case.
40. Remove output shaft assembly according to the following proce-
dures.
a. Remove side cover bolts.
b. Remove side cover by lightly tapping it with a soft hammer.
●Be careful not to drop output shaft assembly. It might
come out when removing side cover.
SAT056D
SAT272E
AAT215A
SAT059D
SAT434D

DISASSEMBLY
AT-431
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
44. Check parking pawl and shaft for damage or wear.
45. Remove parking actuator support from transmission case.
●Check parking actuator support for damage or wear.
46. Remove revolution sensor from transmission case.
SAT066D
SAT311G

AT-432
[ALL]
REPAIR FOR COMPONENT PARTS
REPAIR FOR COMPONENT PARTS
PFP:00000
Manual ShaftECS007TA
COMPONENTS
REMOVAL
1. Remove detent spring from transmission case.
2. Drive out manual plate retaining pin.
SAT481J
SAT313G
AAT486

REPAIR FOR COMPONENT PARTS
AT-433
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
3. Drive and pull out parking rod plate retaining pin.
4. Remove parking rod plate from manual shaft.
5. Draw out parking rod from transmission case.
6. Pull out manual shaft retaining pin.
7. Remove manual shaft and manual plate from transmission case.
8. Remove manual shaft oil seal.
INSPECTION
●Check component parts for wear or damage. Replace if necessary.
INSTALLATION
1. Install manual shaft oil seal.
●Apply ATF to outer surface of oil seal.
AAT534
SAT049F
SAT080D
SAT081D

AT-434
[ALL]
REPAIR FOR COMPONENT PARTS
2. Install manual shaft and manual plate.
3. Align groove of manual shaft and hole of transmission case.
4. Install manual shaft retaining pin.
5. Install parking rod to parking rod plate.
6. Set parking rod assembly onto manual shaft.
7. Drive manual plate retaining pin and parking rod plate retaining
pin.
●Both ends of pin should protrude.
8. Install detent spring.
SAT610H
AAT487
SAT078D
AAT485
SAT313G

AT-470
[ALL]
REPAIR FOR COMPONENT PARTS
15. Check operation of overrun clutch.
Refer to AT- 4 6 4 , "
Forward and Overrun Clutches" .
Low & Reverse BrakeECS007TI
COMPONENTS
DISASSEMBLY
1. Check operation of low & reverse brake.
a. Apply compressed air to oil hole of transmission case.
b. Check to see that retaining plate moves to snap ring.
c. If retaining plate does not contact snap ring:
●D-ring might be damaged.
●Oil seal might be damaged.
●Fluid might be leaking past piston check ball.
2. Stand transmission case.
3. Remove snap ring.
4. Remove drive plates, driven plates, retaining plate from trans-
mission case.
SAT202D
SAT486JA
SAT230D
SAT231D

REPAIR FOR COMPONENT PARTS
AT-471
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
5. Set Tool on spring retainer and remove snap ring while com-
pressing return springs.
●Set Tool directly above return springs.
●Do not expand snap ring excessively.
6. Remove spring retainer and return springs.
●Do not remove return springs from spring retainer.
7. Apply compressed air to oil hole of transmission case while
holding piston.
8. Remove piston from transmission case by turning it.
9. Remove D-ring and oil seal from piston.
AAT687
SAT303E
SAT234D
SAT767G