2003 MITSUBISHI SHOGUN reset

D01A229A
Instruments
ED01AOI
1- Speedometer
2- Fuel gauge
3- Water temperature gauge
4- Tachometer
5- Odometer/Tripmeter
6- Tripmeter reset button
D03A071A
ASpeedometer
ED03A-Na
Type A
The speedometer indicates the vehicle’s
speed in kilometres per hour (km/h).
D03A072A
BType B
The speedometer indicates the vehicle’s
speed in miles per hour (mph) and kilome-
tres per hour (km/h).
Instruments and controls
4-2Div:
Out put date:

D04A056A
Tachometer
ED04A-Ac
The tachometer indicates the engine speed
(r/min). The tachometer can help you obtain
more economical driving and also warns
you of excessive engine speeds.
CAUTION
During travel, watch the tachometer
making sure that the engine speed
indication does not rise to the red
zone (excessive engine rpm).
D03F040A
Odometer/Tripmeter
ED03FAJa
When the ignition switch is turned to the
“ON”position, odometer and tripmeter indi-
cations are given.
Every time the reset button (3) is pressed
lightly (less than 1 second), tripmeter indi-
cations (TRIP
and
) are changed.
1- Odometer
2- Tripmeter
3- Reset button
OdometerThe odometer indicates the total distance
the vehicle has travelled.
D03F018A
TripmeterThe tripmeter indicates the distance trav-
elled during a particular trip or period.
There are two tripmeter displays: TRIP
and
.
TRIP
can be used to measure the dis-
tance travelled since the current trip began.
At the same time, TRIP
can be used to
measure the distance from an intermedi-
ate location. To return the display to zero,
press the reset button for more than 1 sec-
ond. Only the currently displayed value will
be reset.
If TRIP
is displayed, for example, only
TRIPwill be reset.
NOTE
(1) Display TRIP
and
each have a
maximum distance of 999.9km.
Instruments and controls
4-3
Div:
Out put date:

G15B094D
Manual modeThe manual adjustment mode is also available in case the“Auto
mode ”show sth e incorrec ttim ewhe nthe incorrect
RDS signal
is
recieved .
For manual time adjustment, use the below procedure:
1. Switch off the audio once by pressing the PWR switch (1).
2. While pressing the CH4 button (2), press the PWR switch (1) until it beeps. The “CT” display (A) disappears and this is the“Manual adjustment mode”.
3. Set the time by pressing the various buttons as described below. H -To adjust the hour
M -To adjust the minutes
SET -To reset the minutes to zero
10:30-11:29...Changes to 11:00
11:30-12:29...Changes to 12:00
Instruments and controls
4-30Div:
Out put date:

D92I003A
Average fuel consumption
(Petrol-powered vehicles only)
ED92I-Ca
This value shows the average fuel con-
sumption (in L/100 km or mpg) since the
display was reset. If you reset the display
at the time when you want to start the mea-
surements, average fuel consumption from
that point of time can be displayed.
To reset the display
[Vehicles without MITSUBISHI genuine
audio]
Push the button (A) for more than 2 sec-
onds.
D92G002A
Type 1[Vehicles with MITSUBISHI genuine audio]
Push the“DISP”button for more than 2
seconds.
NOTE
(1) When the ignition switch is turned on,
the average fuel consumption which
was being displayed when the igni-
tion switch was previously turned off will
be displayed once again.
(2) Average fuel consumption varies
according to the conditions under which
a vehicle is travelling (road condi-
tions, the manner in which the vehicle
is being driven, etc.).
Observe this display for reference
because the fuel consumption dis-
play may differ from the actual fuel con-
sumption.
D92G003A
Type 2
Instruments and controls
4-32Div:
Out put date:

D92F003A
Average speed
(Petrol-powered vehicles only)
ED92F-E
For vehicles with MITSUBISHI genuine
audio, average speed can be displayed.
This value shows the average speed (in
km/h or mph) since the display was reset.
If you reset the display at the time when
you want to start the measurements, aver-
age speed from that point of time can be
displayed.
D92G002A
Type 1To reset the display, push the“DISP”but-
ton for about 2 seconds or more.
D92G003A
Type 2
Instruments and controls
4-34Div:
Out put date:

D92N009A
Date
(Diesel-powered vehicles only)
ED92N-C
Set the date by pressing the various but-
tons as described below:
1. Press the“M”button while pressing the
button (A) to activate the date setting
function.
2. Press button (A) to select the“day”.
Then, press the“M”or“H”button to
adjust the desired“day”.
To change the date quickly, press the
“M”or“H”button for about 2 seconds or
longer.3. Press the button (A) to select the
“month”. Then, press the“M”or“H”but-
ton to adjust the desired“month”.
To change the month quickly, press the
“M”or“H”button for about 2 seconds or
longer.
4. Press the button (A) to select the“year”.
And then, press the“M”or“H”button to
adjust the desired“year”.
To change the year quickly press the
“M”or“H”button for about 2 seconds or
longer.
5. Press the“SET”button to determine the
setting.
NOTE
(1) If the battery cables are discon-
nected, reset the correct date to cor-
rect the date after reconnecting.
(2) If no buttons are pressed for more than
approx. 15 seconds, the display will
return to the original display.
D92J011A
Display brightness adjustment /
Display unit selection
ED92L-C
Display brightness adjustment
1. Press the“H”button while pressing the
button (A) to activate the display bright-
ness selection function.Instruments and controls
4-35
Div:
Out put date:

D92A059A
Trip computer information
(For petrol-powered vehicles only)
ED92F-G
The following information will be dis-
played from the trip computer system.
1. Average speed
2. Average fuel consumption
3. Driving rangeNOTE
(1) This display is not show for
diesel-powered vehicles.
(2) If this display is shown for
diesel-powered vehicles, there may be
a setting error, or the display may show
the wrong information. Be sure to reset
the car type.
(3) If this display is not shown for
petrol-powered vehicles, there may be
an error in the car type setting.
(4) If the body type“SHORT”or“LONG”is
wrongly selected when selecting
petrol-powered vehicles, the display
may show the wrong information.
Be sure to set the car type again.
→Refer to“Resetting the car type”on
page 4−64.
1. Average speed
2. Average fuel consumption
These values show the average speed (in
km/h or mph) and the average fuel con-
sumption (in L/100 km, or km/L) since the
display was reset. If you reset the display
at the time when you want to start the mea-
surements, average fuel consumption from
that point of time can be displayed.
To reset the display push the“RESET”
function button.NOTE
(1) When the system cannot provide a defi-
nite value for the average speed, this
display shows“
km”.
(2) Average fuel consumption varies
according to the conditions under which
a vehicle is travelling (road condi-
tions, the manner in which the vehicle
is being driven, etc.).
Observe this display for reference
because the fuel consumption dis-
play may differ from the actual fuel con-
sumption.
3. Driving range
This value shows the distance (in km or
miles) that can be driven on the fuel
remaining in the fuel tank.
When the driving range mode is dis-
played and the driving range drops below
50km/h (30miles), the display will blink
orange.
Instruments and controls
4-46Div:
Out put date:

Resetting the car type
ED92M-E
If you select the car type incorrectly, take
the following action.In case the diesel-powered vehicle is
selected incorrectly
1. Turn the ignition switch to the“LOCK”
position.
2. Turn the ignition switch to the“START”
position by pressing the“DISP”but-
ton.
D92M016A
3. By pressing the“DISP”button for more
than 10 seconds this display will appear
automatically.
4. The monitor will revert to the“Car type
setting”display after a while, set the car
type, refer to the“Car type setting”on
page 4-62.
Instruments and controls
4-64Div:
Out put date: