2003 MITSUBISHI SHOGUN display

G15B094D
Manual modeThe manual adjustment mode is also available in case the“Auto
mode ”show sth e incorrec ttim ewhe nthe incorrect
RDS signal
is
recieved .
For manual time adjustment, use the below procedure:
1. Switch off the audio once by pressing the PWR switch (1).
2. While pressing the CH4 button (2), press the PWR switch (1) until it beeps. The “CT” display (A) disappears and this is the“Manual adjustment mode”.
3. Set the time by pressing the various buttons as described below. H -To adjust the hour
M -To adjust the minutes
SET -To reset the minutes to zero
10:30-11:29...Changes to 11:00
11:30-12:29...Changes to 12:00
Instruments and controls
4-30Div:
Out put date:

Display mode
ED92G-I
For petrol-powered vehicles with MITSUB-
ISHI genuine audio, driving range and aver-
age speed can be displayed besides
average fuel consumption by pushing the
“DISP”button in the audio.
When the ignition switch is turned to the
“ON”position, the display shows the 3
items sequentially (Average fuel consump-
tion→Driving range→Average speed)
and returns to the original display that is
shown before the ignition switch was last
turned to the“OFF”position.
NOTE
If the DISP button is pressed while the dis-
play is scrolling through the sequence men-
tioned above, the display stops scrolling
and shows the item that was shown before
the ignition switch was last turned to the
“OFF”position.
D92G002A
Type 1Change of display mode
(Petrol-powered vehicles only)For vehicles with MITSUBISHI genuine
audio, every time the“DISP”button is
pressed lightly (less than 2 seconds), the
display can be changed.
Average fuel consumption→Driving range
→Average speed
D92G003A
Type 2Instruments and controls
4-31
Div:
Out put date:

D92I003A
Average fuel consumption
(Petrol-powered vehicles only)
ED92I-Ca
This value shows the average fuel con-
sumption (in L/100 km or mpg) since the
display was reset. If you reset the display
at the time when you want to start the mea-
surements, average fuel consumption from
that point of time can be displayed.
To reset the display
[Vehicles without MITSUBISHI genuine
audio]
Push the button (A) for more than 2 sec-
onds.
D92G002A
Type 1[Vehicles with MITSUBISHI genuine audio]
Push the“DISP”button for more than 2
seconds.
NOTE
(1) When the ignition switch is turned on,
the average fuel consumption which
was being displayed when the igni-
tion switch was previously turned off will
be displayed once again.
(2) Average fuel consumption varies
according to the conditions under which
a vehicle is travelling (road condi-
tions, the manner in which the vehicle
is being driven, etc.).
Observe this display for reference
because the fuel consumption dis-
play may differ from the actual fuel con-
sumption.
D92G003A
Type 2
Instruments and controls
4-32Div:
Out put date:

D92C045A
Driving range
(Petrol-powered vehicles only)
ED92C-E
For vehicles with MITSUBISHI genuine
audio, driving range can be displayed. This
value shows the distance (in km or miles)
that can be driven on the fuel remaining in
the fuel tank.NOTE
(1) When the driving range is displayed, if
the driving range drops below 50km
(30miles), alarm sounds and the dis-
play shows a flashing. When this
occurs, top up the fuel tank as soon as
possible.
Even when an item other than the driv-
ing range is currently displayed, the
alarm sounds and the driving range
appears for 5 seconds when the driv-
ing range drops to 50km, 25km and
10km (or 30 miles, 15miles and 6
miles) levels. Then, the original item is
again displayed.
(2) The driving range varies depending on
road conditions, the manner of driv-
ing and other related factors. Conse-
quently, the display should be used
only as a guide. It is recommended to
add fuel as soon as the low fuel indi-
cation lamp in the instrument cluster
illuminates.
(Refer to“Low fuel indication lamp”on
page 4-9.)
(3) Refueling will update the driving range
indication. However, when the amount
of refueling is too little, the correct
range will not be displayed, so make
sure to supply the minimum amount of
fuel (25 litres or more).(4) The driving range displayed is based on
previous fuel consumption data. Dis-
connecting the battery cable will result
in the deletion of existing fuel consump-
tion data, which will affect the unit’s cal-
culations.
(5) The driving range figure can occasion-
ally increase if the vehicle is stopped on
an incline. This is because the fuel has
moved in the tank because of the
incline and is not considered as a fault.
Instruments and controls
4-33
Div:
Out put date:

D92F003A
Average speed
(Petrol-powered vehicles only)
ED92F-E
For vehicles with MITSUBISHI genuine
audio, average speed can be displayed.
This value shows the average speed (in
km/h or mph) since the display was reset.
If you reset the display at the time when
you want to start the measurements, aver-
age speed from that point of time can be
displayed.
D92G002A
Type 1To reset the display, push the“DISP”but-
ton for about 2 seconds or more.
D92G003A
Type 2
Instruments and controls
4-34Div:
Out put date:

D92N009A
Date
(Diesel-powered vehicles only)
ED92N-C
Set the date by pressing the various but-
tons as described below:
1. Press the“M”button while pressing the
button (A) to activate the date setting
function.
2. Press button (A) to select the“day”.
Then, press the“M”or“H”button to
adjust the desired“day”.
To change the date quickly, press the
“M”or“H”button for about 2 seconds or
longer.3. Press the button (A) to select the
“month”. Then, press the“M”or“H”but-
ton to adjust the desired“month”.
To change the month quickly, press the
“M”or“H”button for about 2 seconds or
longer.
4. Press the button (A) to select the“year”.
And then, press the“M”or“H”button to
adjust the desired“year”.
To change the year quickly press the
“M”or“H”button for about 2 seconds or
longer.
5. Press the“SET”button to determine the
setting.
NOTE
(1) If the battery cables are discon-
nected, reset the correct date to cor-
rect the date after reconnecting.
(2) If no buttons are pressed for more than
approx. 15 seconds, the display will
return to the original display.
D92J011A
Display brightness adjustment /
Display unit selection
ED92L-C
Display brightness adjustment
1. Press the“H”button while pressing the
button (A) to activate the display bright-
ness selection function.Instruments and controls
4-35
Div:
Out put date:

D92J006A
2. Adjust the brightness by moving the cur-
sor with the“H”or“M”button.
H-Decrease brightness
M-Increase brightness
D92J012A
3. Press the“SET”button to determine the
setting. The display will return to the
original display item.
NOTE
(1) To cancel the brightness adjusting pro-
cedure before completion, press the
button (A).
(2) If no buttons are pressed for more than
approx. 15 seconds, the currently
selected brightness is set automati-
cally. Then, the display returns to the
original display item.
D92J013A
Display unit selection
(Petrol-powered vehicles only)
ED92J-B
Originally, km/h and L/100km are selected.
When you want to select the unit“mile”, fol-
low this procedure.
NOTE
For vehicles without MITSUBISHI genu-
ine audio, only the unit of average fuel con-
sumption can be changed to km or miles
as you like.
1. Press the“M”button while pressing the
button (A) to activate the display unit
selection function. The currently selected
unit will appear.
Instruments and controls
4-36Div:
Out put date:

D92J014A
2. Use the“H”or“M”button to select the
desired speed unit, then press the“SET”
button to enter the setting.
H-km
M-mile
D92J015A
3. If the km unit was selected in step 2, the
fuel consumption unit must be selected
continuously using the“H”or“M”but-
ton. The currently selected unit will
appear.
Use the“H”or“M”button to select the
desired fuel consumption unit, then
press the“SET”button to enter the set-
ting.
H-L/100Km
M-Km/L
D92J012A
4. Press the“SET”button to determine the
setting. The display will return to the
original display item.
NOTE
(1) If you select“M”(mile) unit in the step
2, fuel consumption is automatically
shown in the“mpg (mile per gallon)”.
(2) To cancel the unit setting procedure
before completion, press the button (A).
(3) The outside temperature and clock are
not shown during the unit selecting pro-
cedure.Instruments and controls
4-37
Div:
Out put date: