2003 MAZDA MODEL PROTÉGÉ Owners Manual (in English)

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8Q94-EA-02G

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
: Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
CHASSIS and BODY
AIR CONDITIONER SYSTEM (if equipped)
*1 According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage period to ensure long-term reliability.
Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)Months 6 12182430364248
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Engine valve clearanceI
Engine timing belt Inspect at 96,000km (60,000 miles)
Replace every 168,000 km (105,000 miles)
Drive belts (tension) II
Engine oilRRRRRRRR
Engine oil filterRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000 km (45,000 miles) or 36 months ;
after that, every 48,000 km (30,000 miles) or 24 months
Idle speedII
Air filterRR
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Spark plugsRR
Brake lines, hoses and connectionsII
Disc brakesII
Drum brakesII
Steering operation and linkagesII
Front suspension ball jointsII
Driveshaft dust bootsII
Bolts and nuts on chassis and bodyII
Exhaust system heat shieldsII
All locks and hingesLLLLLLLL
Refrigerant amountIIII
Compressor operationIIII
J39L_EA.book Page 4 Saturday, June 8, 2002 5:35 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q94-EA-02G

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.)
R
: Replace
L
: Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
ELECTRICAL SYSTEM
CHASSIS and BODY
AIR CONDITIONER SYSTEM (if equipped)
*1 According to state and federal regulations, failure to perform maintenance on these items will not void your
emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or mileage period to ensure long-term reliability
*2 If the vehicle is operated in cold districts { below -18 degrees C (0 degrees F) }, replace the timing belt at
96,000 km (60,000 miles).
Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Engine valve clearanceI
Engine timing belt
*2Inspect at 96,000 km (60,000 miles)
Replace every 168,000 km (105,000 miles)
Drive belts (tension) II
Engine oilPuerto RicoReplace every 5,000 km (3,000 miles) or 3 months
OthersRRRRRRRRRRRR
Engine oil filterRRRRRRRRRRRR
Cooling systemII
Engine coolantReplace at first 72,000 km (45,000 miles) or 36 months ;
after that, every 48,000 km (30,000 miles) or 24 months
Engine coolant levelIIIIIIIIIIII
Idle speedII
Air filter
I
*1R
I*1R
Fuel lines and hoses*1II
Hoses and tubes for emission*1I
Spark plugsRR
Function of all lightsIIIIIIIIIIII
Brake lines, hoses and connectionsII
Brake and clutch fluid level IIIIIIIIIIII
Disc brakesIIII
Drum brakesII
Tire inflation pressure and tire wearIIIIIIIIIIII
Steering operation and linkagesII
Power steering fluid levelIIIIIIIIIIII
Front suspension ball jointsII
Driveshaft dust bootsII
Bolts and nuts on chassis and bodyIIII
Exhaust system heat shieldsII
All locks and hingesLLLLLLLLLLLL
Washer fluid levelIIIIIIIIIIII
Refrigerant amountIIII
Compressor operationIIII
J39L_EA.book Page 5 Saturday, June 8, 2002 5:35 PM

8-6
Maintenance and Care
Form No. 8Q94-EA-02G
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.

When Refueling
•Brake and clutch fluid level (page 8-14)
•Engine coolant level (page 8-12)
•Engine oil level (page 8-9)
•Washer fluid level (page 8-18)

At Least Monthly
•Tire inflation pressures (page 8-25)

At Least Twice a Year (For Example, Every Spring and Fall)
•Automatic transaxle fluid level (page 8-16)
•Power steering fluid level (page 8-16)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
•Air filter (page 8-19)
•Engine coolant (page 8-12)
•Engine oil (page 8-10)
Owner Maintenance Schedule
J39L_EA.book Page 6 Saturday, June 8, 2002 5:35 PM

8-7
Maintenance and Care
Owner Maintenance
Form No. 8Q94-EA-02G
Improper or incomplete service may result in problems. This section gives instructions
only for items easy to perform.
As explained in the Introduction (page 8-2), several procedure can be done only by a
qualified service technician with special tools.
Improper owner maintenance during the warranty period may affect warranty coverage.
For details, read the separate Mazda Warranty statement provided with the vehicle. If
you’re unsure about any servicing or maintenance procedure, have it done by an
Authorized Mazda Dealer.
There are strict environmental laws regarding the disposal of waste oil and fluids. Please
dispose of your waste carefully and with due regard to the environment.
We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized
Mazda Dealer.
Owner Maintenance Precautions
Maintenance Procedures:
Performing maintenance work on a vehicle is dangerous if not done properly. You can
be seriously injured while performing some maintenance procedure. If you lack
sufficient knowledge and experience or the proper tools and equipment to do the
work, have it done by a qualified technician.
Running the Engine:
Working under the hood with the engine running is dangerous. It becomes even more
dangerous when you wear jewelry or loose clothing.
Either can become entangled in moving parts and result in injury.
Therefore, if you must run the engine while working under the hood, make certain
that you remove all jewelry (especially rings, bracelets, watches, and necklaces) and
all neckties, scarves, and similar loose clothing before getting near the engine or
cooling fan.
Electrical Fan and Engine Inspection:
Inspecting the engine with the ignition switch in the ON position is dangerous. The
cooling fan could come on unexpectedly even when the engine isn’t running. You
could be seriously injured by the fan. Turn the ignition switch off and remove the key
from the ignition switch when you inspect the engine.
WARNING
J39L_EA.book Page 7 Saturday, June 8, 2002 5:35 PM

8-8
Maintenance and Care
Owner Maintenance
Form No. 8Q94-EA-02G
Engine Compartment Overview
Automatic transaxle fluid-level dipstick (only for automatic transaxle)
Brake/Clutch fluid reservoir
Battery
Fuse block
Engine coolant reservoir
Air filter
Cooling system cap Engine oil dipstick Engine oil filter 1.6-liter engine
2.0-liter engineEngine oil-filler cap
Power steering
fluid reservoir
Windshield washer
fluid reservoir
Automatic transaxle fluid-level dipstick (only for automatic transaxle)
Brake/Clutch fluid reservoir
Battery
Fuse block
Engine coolant reservoir
Air filter Cooling system cap Engine oil filter Engine oil-filler cap
Engine oil dipstick
Power steering
fluid reservoir
Windshield washer
fluid reservoir
J39L_EA.book Page 8 Saturday, June 8, 2002 5:35 PM

8-9
Maintenance and Care
Owner Maintenance
Form No. 8Q94-EA-02G

Recommended Oil
Oil container labels provide important
information.
The quality designation SG, SH, SJ, SL,
or ILSAC
must be on the label.
Engine oil viscosity, or thickness, has an
effect on fuel economy and cold-weather
operation (starting and oil flow).
Low-viscosity engine oils can provide
improved fuel economy and cold-weather
performance.
But high-temperature weather conditions
require higher-viscosity engine oils for
satisfactory lubrication.When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended viscosity
from this chart.
Energy conserving oils are recommended.
A chief contribution they make to fuel
economy is reducing the amount of fuel
necessary to overcome engine friction.

Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
Engine Oil
SAEFORGASOLINEENGINES10W-30
(ILSAC)
–30–20–100 1020304050
–20 0 20 40 60 80 100 120
5W-30
10W-30
Using oils of viscosity besides those
recommended for specific temperature
ranges could result in engine damage.
CAUTION
Full 1.6-liter engine
Low OK
J39L_EA.book Page 9 Saturday, June 8, 2002 5:35 PM

8-10
Maintenance and Care
Owner Maintenance
Form No. 8Q94-EA-02G
5. Pull it out again and examine the level.
It’s OK between L and F.
But if it’s near at or below L, add
enough oil to bring the level to F.
6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.
The distance between L and F on the
dipstick represents the following:

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Changing engine oil
Don’t add engine oil over F. This may
cause engine damage.
L (US qt, Imp qt) 1.0 (1.05, 0.87)
Full 2.0-liter engine
Low OK
CAUTION
Handling Used Engine Oil:
Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Checking or Changing Engine Oil:
Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don’t check or
change the engine oil when the
engine is hot.
WARNING
WARNING
1.6-liter engine
Loosen Tighten
Front
Drain
plug
J39L_EA.book Page 10 Saturday, June 8, 2002 5:35 PM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8Q94-EA-02G
1. Warm up the engine for a few minutes
and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil
into a suitable container.
3. Replace the plug tightly after the oil
has thoroughly drained.
4. Fill the engine with new oil to the F
mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the
drain plug for leaks.
7. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
Check the oil level and fill to the F mark if
necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)Changing oil filterBecause you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.
2.0-liter engine
Loosen
Tighten
Front
Drain
plugNOTE
•The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
•Use only specified engine oil (page
10-4).
J39L_EA.book Page 11 Saturday, June 8, 2002 5:35 PM