2003 LEXUS LS430 park

INSPECTION
1.INSPECT SPARK PLUG
a. Check the electrode.
1. Using an megaohmmeter, measure the insulation resistance.
Correct insulation resistance: 10 Mohms or higher
Fig. 5: Checking Electrode

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

If the resistance is less than the specified value, proceed to step (d).
HINT:
If the megaohmmeter is not available, perform the following simple inspection instead.
b. Alternative inspection method:
1. Quickly accelerate the engine to 4,000 rpm 5 times.
2. Remove the spark plug.
3. Visually check the spark plug.
If the electrode is dry, the spark plug is functioning. Reinstall the spark plug. Proceed to step
3.
If the electrode is damp, proceed to steps (c), (d) and (e).

Fig. 6: Alternative Inspection Method
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Check the spark plug for any damage on its thread and insulator.
If there is any damage, replace the spark plug. If not, reinstall the spark plug.
RECOMMENDED SPARK PLUG TABLE
DENSO madeSK20R11

d. Check the spark plug electrode gap.
Maximum electrode gap for used spark plug: 1.3 mm (0.051 in.)
If the gap is greater than the maximum, replace the spark plug.
Correct electrode gap for new spark plug: 1.0 to 1.1 mm (0.039 to 0.043 in.)
Fig. 7: Checking Spark Plug Electrode Gap

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e. Clean the spark plu
gs.
NGK madeIFR6A11

If the electrode his traces of wet carbon, clean the electrode with a spark plug cleaner and then dry
it.
Fig. 8: Cleaning Spark Plugs

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Air pressure: 588 kPa (6 kgf/cm
2 , 85 psi)
Duration: 20 seconds or less

HINT:
Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil,
use gasoline to clean off the oil before using the spark plug cleaner.
2.INSPECT CAMSHAFT POSITION SENSOR
a. Using an ohmmeter, measure the resistance between the terminals.
CAMSHAFT POSITION SENSOR - REFERENCE TABLE
Fig. 9: Inspecting Camshaft Position Sensor

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
If the resistance is not as specified, replace the sensor.
3.INSPECT CRANKSHAFT POSITION SENSOR
ConditionSpecified Condition
Cold835 to 1,400 ohms
Hot1,060 to 1,645 ohms

4.REMOVE OIL LEVEL GAGE SUB-ASSY (See step 8 in REPLACEMENT )
5.REMOVE IGNITION COIL ASSY
a. Disconnect the ignition coil connector.
b. Remove the bolt and pull out the ignition coil.
Fig. 12: Removing Ignition Coil Assy

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
6.INSTALL IGNITION COIL ASSY
a. Connect a new ignition coil to the spark plug, attach the ignition coil to the cylinder head cover,
and install the bolt.
Torque: 7.5 N.m (76 kgf.cm, 66 in.lbf)
b. Connect the ignition coil connector.
7.INSTALL OIL LEVEL GAGE SUB-ASSY (See step 27 in REPLACEMENT
)
8.INSTALL INTAKE AIR CONNECTOR PIPE
9.INSTALL V-BANK COVER
10.INSTALL ENGINE ROOM SIDE COVER

Fig. 8: Removing Instrument Panel Under Cover Sub-Assy No. 1
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
17.REMOVE COIN BOX ASSY
a. Pull the parking brake and remove the 2 nuts from the coin box assy.
b. Using a moulding remover, disengage the 2 claws and remove the coin box assy.
HINt:
Use a screwdriver if a moulding remover is not available.
tape up the screwdriver tip before use.
c. Disconnect the connectors.