2003 FORD MUSTANG engine

10. If the vehicle stalls in (D) or manual 2 at idle with vehicle at a stop, move the transmission range
selector lever to manual 1 position. If the vehicle stalls, see torque converter operation
concerns. For additional information, refer to Diagnosis By Symptom in this section. If the
vehicle does not stall in (D), refer to Diagnosis By Symptom in this section.
11. If the vehicle exhibits a vibration during the road test, complete the Road Test Evaluation Form. This form will aid the technician in determining the source of the vibration.
NOTE: The following is a list of common vehicle concerns that have been misdiagnosed as torque
converter clutch shudder. For diagnosis of the following items refer to the appropriate sections of the
workshop manual and the Powertrain Control/Emissions Diagnosis (PC/ED) manual.
zspark plugs - check for cracks, high resistance or broken insulators
z plug wires
z fuel injector - filter may be plugged
z fuel contamination - poor engine performance
z EGR valve - valve may let in too much exhaust gas and cause engine to run lean
z vacuum leak - engine will not get correct air/fuel mixture
z MAP/MAF sensor - incorrect air/fuel mixture
z HO2S sensor - too rich/lean air/fuel mixture
z fuel pressure - may be too low
z engine mounts - loose/damaged mounts can cause vibration concerns
z axle joints - check for vibration Torque Converter Road Evaluation Form
1) Does the Torque Converter
Engage/Disengage? Yes ·
GO to Step 2. No ·
REFER to Diagnosis By Symptom —
Torque Converter No Apply Routine
240/340 and Always Applied Routine
241/341 in this section for further
diagnosis information. Repair as
required, verify converter operation
and then continue. 2) Does vibration occur during 3-
4 or 4-3 shift at:
light, medium, or heavy throttle? Light ·
May be torque converter clutch
shudder. GO to Step 3. Medium ·
May be torque converter clutch
shudder. GO to Step 3. Heavy ·
Not torque converter clutch shudder
— converter does not engage due to
PCM strategy. REFER to Section 100 - 04 and
Diagnosis By Symptom —
Noise/Vibration Routine 254/354
in this section for further diagnosis. 3) Is the problem vehicle speed dependent Yes ·
Not torque converter clutch shudder Klj . 2 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

(operating at steady speed, i.e. 64 km/h (40 mph)
regardless of transmission range. Verify by
manually selecting 2nd, OD cancel, and OD. —
REFER to Section 100 - 04 and
Diagnosis By Symptom —
Noise/Vibration Routine 254/354 in
this section for further diagnosis. No ·
GO to Step 4. 4) Is the problem engine-
rpm dependent?
(Occurs at the same engine rpm independent of
transmission gear. Verify by holding same rpm in
each transmission gear.) Yes ·
Not torque converter clutch shudder
— REFER to Section 100 - 04 and
Diagnosis By Symptom —
Noise/Vibration Routine 254/354 in
this section for further diagnosis. No ·
GO to Step 5. 5) Does the problem occur in coast, steady
speed, or reverse range? Yes ·
Not torque converter clutch shudder
— REFER to Section 100 - 04 and
Diagnosis By Symptom —
Noise/Vibration Routine 254/354 in
this section for further diagnosis. No ·
GO to Step 6. 6) Does vibration occur during extended light
brake application? Yes ·
Not torque converter clutch shudder
— REFER to Section 100 - 04 ,
Section 206 - 00 and
Diagnosis By Symptom —
Noise/Vibration Routine
254/354 in this section for further
diagnosis. No ·
GO to Step 7. 7) If one of the driving modes in Step 2 identifies
a vibration which was not present in Steps 3-
6,
then there is a strong possibility that the vibration
is caused by the torque converter clutch function.
Carry out the repair procedures as found under
Disassembly/Assembly. Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Visual Inspection
This inspection will identify modifications or additions to the vehicle operating system that may affect
diagnosis. Inspect the vehicle for non-
Ford factory add-on devices such as:
z electronic add- on items:
„ air conditioning
„ generator (alternator)
„ engine turbo
„ cellular telephone
„ cruise control
„ CB radio
„ linear booster
„ backup alarm signal
„ computer
z Vehicle modification:
These items, if not installed correctly, will affect the powertrain control module (PCM), or transmission
function. Pay particular attention to add- on wiring splices in the PCM harness or transmission wiring
harness, abnormal tire size, or axle ratio changes.
zLeaks; refer to Leak Inspection.
z Correct linkage adjustments; refer to Section 307 - 05 .
Shift Linkage Check
Check for a misadjustment in shift linkage by matching the detents in the transmission range selector
lever with those of the manual lever in the transmission. If they match, the misadjustment is in the
indicator. Do not adjust the shift linkage.
Hydraulic leakage at the manual control valve can cause delay in engagements and/or slipping while
operating if the linkage is not correctly adjusted. Refer to Section 307 - 05 for shift linkage adjustment.
Check TSBs and OASIS
Refer to all technical service bulletins (TSB) and OASIS messages which pertain to the transmission
concern and follow the procedure as described.
Carry Out On- Board Diagnostics (KOEO, KOER)
After a road test, with the vehicle warm and before disconnecting any connectors, carry out the Quick
Test using the scan tool. Refer to the Powertrain Control/Emissions Diagnosis (PC/ED) manual. SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

Diagnosing an electronically controlled automatic transmission is simplified by using the following
procedures. One of the most important things to remember is that there is a definite procedure to
follow. DO NOT TAKE SHORT CUTS OR ASSUME THAT CRITICAL CHECKS OR ADJUSTMENTS
HAVE ALREADY BEEN MADE. Follow the procedures as written to avoid missing critical components
or steps. By following the diagnostic sequence, the technician will be able to diagnose and repair the
concern the first time.
On-
Board Diagnostics With Diagnostic Tool
NOTE: For detailed instruction and other diagnostic methods using the scan tool, refer to the scan tool
tester manual and the Powertrain Control/Emissions Diagnosis (PC/ED) manual. These quick tests
should be used to diagnose the powertrain control module (PCM) and should be carried out in order.
zQuick Test 1.0 - Visual Inspection
z Quick Test 2.0 - Set Up
z Quick Test 3.0 - Key On, Engine Off (KOEO)
z Quick Test 4.0 - Continuous Memory
z Quick Test 5.0 - Key On, Engine Running (KOER)
„ Special Test Mode
„ Wiggle Test
„ Output Test Mode
„ PCM Reset Mode
„ Clearing DTCs
„ OBD II Drive Cycle
z Other Scan Tool Features
For further information on other diagnostic testing features using the scan tool, refer to the Powertrain
Control/Emissions Diagnosis (PC/ED) manual. Other diagnostic methods include the following:
„Parameter Identification (PID) Access Mode
„ Freeze Frame Data Access Mode and Manual
007-
00131 or equivalent 73 III Automotive Meter
105-
R0057 or equivalent UV Leak Detector Kit
164-
R0756 or equivalent Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Output State Control (OSC) Mode
Output State Control (OSC) allows the technician to take control of certain parameters to function the
transmission. For example, OSC allows the technician to shift the transmission only when he/she
commands a gear change. If the technician commands 1st gear in OSC, the transmission will remain
in 1st gear until the technician commands the next gear. Another example, the technician can
command a shift solenoid to turn on or off when carrying out an electrical circuit check. OSC has two
modes of operation for transmission, the BENCH MODE and the DRIVE MODE. Each
mode/parameter has a unique set of vehicle operating requirements that the technician is required to
meet before being allowed to operate OSC.
NOTE:
To operate OSC the digital transmission range (TR) sensor must be operational. No Diagnostic
Trouble Codes (DTCs) related to the digital TR sensor can be present.
To operate OSC the vehicle speed source must be operational. No diagnostic codes (DTCs) related to
this source can be present. The vehicle speed source can vary depending on vehicle configuration.
Technicians should verify which input source is applicable for their vehicle application. The following
are potential vehicle speed sources:
„anti- lock braking system (ABS)
„ output shaft speed (OSS) sensor
„ vehicle speed sensor
z The vehicle requirements MUST BE MET when SENDING the OSC value. Refer to individual
test modes for vehicle requirements.
z If the vehicle requirements are NOT MET when SENDING the OSC value, an ERROR
MESSAGE will appear. When the ERROR MESSAGE is received, OSC is aborted and must be
restarted.
z If AFTER SENDING an OSC value, and the vehicle requirements are no longer met, the PCM
will cancel the OSC value and NO ERROR message will appear. Once the vehicle requirements
are met again, the PCM will automatically SEND the previous OSC value without any additional
actions required by the service technician.
z The OSC value XXX may be sent anytime to cancel OSC.
Output State Control (OSC) Procedures
zCarry out visual inspection and vehicle preparation as required.
z Select "Vehicle and Engine Selection" menu.
z Select appropriate vehicle and engine.
z Select "Diagnostic Data Link."
z Select "Powertrain Control Module."
z Select "Output Test Mode."
z Select "KOEO On- Demand Self Test and KOER On- Demand Self Tests."
z Carry out test and record DTCs.
z Repair all NON- Transmission DTCs.
z Repair all digital TR Sensor DTCs.
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Klj . 1 ba
92003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

z
Repair all vehicle speed DTCs.
z Make sure that the vehicle speed sensor and digital TR sensors are functional.
z Select "Active Command Modes."
z Select "Trans - Bench Mode or Trans - Drive Mode."
OSC — Transmission Bench Modes
The following Transmission Bench Modes may be used or required during diagnostics.
SSA, SSB and TCC in BENCH MODE
The BENCH MODE allows the technician to carry out electrical circuit checks on the following
components:
zSSA - activates SSA OFF or ON.
z SSB - activates SSB OFF or ON.
z Transmission converter clutch (TCC) - activates TCC OFF or ON.
OSC "SSA, SSB, TCC" BENCH MODE operates ONLY when:
zthe digital TR sensor is operational and no digital TR sensor DTCs are present.
z the vehicle speed input is operational and no VSS sensor DTCs are present.
z the transmission range selector lever is in P.
z the key is ON.
z the engine is OFF.
OSC Command Values
zOFF - turns solenoid OFF.
z ON - turns solenoid ON.
z XXX - cancels OSC value sent.
z SEND - sends the values to PCM.
BENCH MODE Procedure for SSA, SSB and TCC
Follow operating instructions from the scan tool menu screen:
zSelect "Output State Control."
z Select "Trans - Bench Mode."
z Select "PIDs" to be monitored.
z Monitor all selected PIDs during test.
z Select "Parameters - SSA, SSB or TCC."
z Select "ON" to turn solenoid ON.
z Press "SEND" to send command ON.
z Select "OFF" to turn solenoid OFF.
z Press "SEND" to send command OFF. Klj . 2 ba
92003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

z
Select "XXX" to cancel at any time.
z Press "SEND."
EPC in BENCH MODE
The BENCH MODE is also used to test the functionality of the transmission's electronic pressure
control. During BENCH MODE, the electronic pressure control (EPC) solenoid can ramp up/down in
increments of 103 kPa (15 psi) from zero to 620 kPa (90 psi) and 620 kPa (90 psi) to zero psi.
The OSC functions for the parameter EPC allows the technician to choose the following options:
zEPC - activates EPC to selected values.
z 00 - sets EPC pressure to 00 kPa (00 psi).
z 15 - sets EPC pressure to 103 kPa (15 psi).
z 30 - sets EPC pressure to 206 kPa (30 psi).
z 45 - sets EPC pressure to 310 kPa (45 psi).
z 60 - sets EPC pressure to 411 kPa (60 psi).
z 75 - sets EPC pressure to 517 kPa (75 psi).
z 90 - sets EPC pressure to 620 kPa (90 psi).
To carry out an EPC BENCH MODE pressure functionality test, install a pressure gauge in the EPC
port. The following requirements are required to carry out this test:
zVSS and digital TR sensor operational
z No VSS and digital TR sensor DTCs
z Transmission range selector lever in P
z Key ON
z Engine ON
z Engine speed at least 1,500 rpm for accurate EPC pressure measurement
To carry out an EPC BENCH MODE solenoid circuit pinpoint test, the following requirements are
required.
zVSS and digital TR sensor operational
z No VSS and digital TR sensor DTCs
z Transmission range selector lever in P
z Key ON
z Engine OFF
OSC Command Values
z00 - sets EPC pressure to 00 kPa (00 psi).
z 15 - sets EPC pressure to 103 kPa (15 psi).
z 30 - sets EPC pressure to 206 kPa (30 psi).
z 45 - sets EPC pressure to 310 kPa (45 psi).
z 60 - sets EPC pressure to 411 kPa (60 psi). Klj . 3 ba
92003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

z
the engine is ON.
z the TCC is OFF.
z the transmission range selector lever is in O/D.
z the vehicle speed is greater than 3.2 km/h (2 mph).
OSC Command Values
z1 - PCM selects 1st gear.
z 2 - PCM selects 2nd gear.
z 3 - PCM selects 3rd gear.
z 4 - PCM selects 4th gear.
z XXX - cancels OSC value sent.
z SEND - sends the values to PCM.
DRIVE MODE Procedure for GR_CM
Follow operating instructions from the scan tool menu screen.
zSelect "Output State Control."
z Select "Trans - DRIVE MODE."
z Select "PIDs" to be monitored.
z Monitor all selected PIDs during test.
z Select "Parameters - GR_CM."
z Select Value "1- 4."
z Press "SEND" to send command.
z Re- Select Value "1- 4."
z Press "SEND" to send command.
z Select "XXX" to cancel at any time.
z Press "SEND."
TCC in DRIVE MODE
This OSC function is used to test whether the torque converter clutch is engaging and disengaging
correctly.
The OSC functions for the TCC parameter allows the technician to choose the following:
zTCC - activates TCC OFF and ON.
z ON - turns TCC solenoid ON.
z OFF - turns TCC solenoid OFF.
OSC "TCC OFF" DRIVE MODE operates ONLY when:
zthe digital TR sensor is operational and no digital TR sensor DTCs are present.
z the vehicle speed sensor is operational and no VSS sensor DTCs are present. Klj . 5 ba
92003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...