2003 FORD MUSTANG wiring

28. Connect the degas bottle return hose.
29. Connect the degas bottle vent hose.
30. Connect the wiring harness anchor to the valve cover.
31. Install the positive crankcase ventilation (PCV) valve hose and connect the electrical connector. Klj . 18 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

19.
NOTE: Do not completely remove the bolts.
Loosen the bolts.
20. Lower the front sub- frame.
21. Remove the sub- frame brace.
22. Remove the starter wiring harness nuts and position the wiring harness out of the way. Klj . 4 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Install the oil pan drain plug.
7. Position the starter wiring harness and install the wiring harness nuts.
8. Install the sub-
frame brace. Klj . 7 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13.
NOTE: Mark the bolts and the crossmember location for assembly reference.
NOTE: RH shown, LH similar.
Remove the four bolts.
14. NOTE: RH shown, LH similar.
Remove the four bolts.
15. Using the jackstands, lower the front subframe.
RH mount 16. Remove the nut and detach the wiring harness.
17. Remove the bolts, the studbolt and the engine mount. Klj . 4 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Attach the ground cables and install the nuts.
RH mount 3. Position the engine mount and install the bolts and studbolt.
4. Attach the wiring harness and install the nut. Both mounts Klj . 6 ba
102003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

14. Remove the bolts and detach the retainer. Position the cables and the bracket aside.
15. Disconnect the evaporative emissions return line.
16. Disconnect the 16-
pin and the 42-pin connectors.
17. Separate the engine control sensor wiring in three locations and position onto the engine.
18. Disconnect the vacuum hoses. Klj . 4 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

19. Disconnect the heater hoses.
20. Remove the wiring support bracket.
21. Disconnect the connectors.
22. Raise the cover and remove the nut and cables. Klj . 5 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

NOTE:
Do not rotate the driveshaft.
Using a suitable tool, disconnect the driveshaft flange from the rear axle flange and remove the
driveshaft.
40. Index- mark the transmission output shaft at the six o'clock position.
41. Remove the starter motor terminal cover.
42. Disconnect the starter wiring. 1. Remove the nut and disconnect the battery positive cable.
2. Remove the nut and disconnect the starter solenoid wire. Klj . 10 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...