2003 FORD MUSTANG wiring

46. Remove the nut and the wiring harness bracket.
47. Remove the nuts and position the wiring harness aside.
48. Disconnect the oil pressure sensor.
49. Remove the nut and the engine ground cable.
50. Disconnect the hose from the oil filter adapter. Klj . 12 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

55. Remove the ground strap bolt.
56. Remove the degas bottle support bracket.
57. Install the two bolts from the RH lifting bracket.
58. Disconnect the reversing lamp switch electrical connector, and the wiring harness from the
transmission. Klj . 14 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

65. Remove the bolts.
All vehicles 66. Lower the transmission, remove the seven bolts, and remove the transmission.
67. NOTE: RH side shown, LH side similar.
Remove the two engine mount nuts.
68. Remove the transmission wiring harness. 1. Remove the RH oxygen sensor connector from the bracket.
2. Disconnect the transmission wiring connector and remove the harness. Klj . 17 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

40. Remove the bolts and the RH valve cover.
41. Remove the knock sensor wiring harness.
1. LH knock sensor electrical connector.
2. RH knock sensor electrical connector.
3. Engine control sensor electrical connector.
4. Fuel injector electrical connector.
5. A/C compressor electrical connector.
6. Crankshaft position sensor (CKP) electrical connector.
42. Remove the knock sensors. Klj . 12 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

59. Install the knock sensor wiring harness.
1. LH knock sensor electrical connector
2. RH knock sensor electrical connector
3. Engine control sensor electrical connector
4. Fuel injector electrical connector
5. A/C compressor electrical connector
6. CKP sensor electrical connector
60. Install the lower intake manifold. zPosition the gaskets.
z Install the intake manifold and tighten the bolts in the sequence shown.
61. Install the generator. Klj . 21 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

69. Connect the throttle position (TP) sensor electrical connector.
70. Connect the idle air control (IAC) valve electrical connector.
71. Connect the generator wiring. Klj . 24 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Manual transmission vehicles
2. Install the clutch cable and retaining screws.
All vehicles 3. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
4. Connect the transmission wiring harness. 1. Connect the RH oxygen sensor connector retainer.
2. Connect the transmission harness electrical connector.
5. NOTE: RH side shown, LH side similar.
Install the LH and RH engine mount nuts. Klj . 2 ba
182003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Install the clutch release lever cover and bolt.
All vehicles 14. Connect the output shaft speed (OSS) sensor electrical connector and attach the left and right oxygen sensor electrical connectors to the crossmember.
15. Connect the reversing lamp switch electrical connector and the wiring harness to the transmission.
16. Remove the two bolts from the RH lifting bracket. Klj . 5 ba
182003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...