2003 FORD MUSTANG manual transmission

5. Disconnect the TCS connector.
6.
CAUTION: Extra force may be needed to lift up on the handle. Do not to pull too far
or damage to the overdrive cancel button may result, as the wires may be pulled out of
the switch.
Remove the screw and the handle.
7. Remove the transmission control switch. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Bezel
Removal
1. Remove the shifter top control panel.
2. Disconnect the electrical connectors.
3. Remove the shifter bezel. 4. Remove the bulb from the bezel. SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Bulb
Removal and Installation
1. Remove the floor console. For additional information, refer to Section 501 - 12 .
2. Remove the bolts, then position the bezel upward.
3. Remove the bulb socket from the bezel.
4. Remove the bulb.
5. To install, reverse the removal procedure.
SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Knob
Removal
1. Remove the shifter top control panel.
2. Disconnect the electrical connectors.
3. Remove the shifter bezel. 4. Remove the bulb from the bezel. SECTION 307-
05: Automatic Transaxle/Transmission External Controls 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

5. Disconnect the TCS connector.
6.
CAUTION: Extra force may be needed to lift up on the handle. Do not to pull too far
or damage to the overdrive cancel button may result, as the wires may be pulled out of
the switch.
Remove the screw and the handle.
7. Remove the transmission control switch. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

SPECIFICATIONS
SECTION 308-
00: Manual Transaxle/Transmission and Clutch — General
Information 2003 Mustang Workshop
Manual General Specifications
Item Specification
Pressure plate
Pressure spring Belleville
Sensor spring Belleville
Clutch Disc (3.8L)
Clutch diameter 280 mm (11.0 inches)
Number of springs 5
Color identification none
Clutch Disc (4.6L 2V)
Clutch diameter 280 mm (11.0 inches)
Number of springs 4
Color identification none
Lubricants (Spec and Capacity) Fluid
T50D-
MERCON® Multi- Purpose ATF Transmission Fluid XT -2-QDX 2.6L (2.8 qt)
TR3650-
Synthetic MERCON® ( ATF) Transmission Fluid E6AZ-19582- B 3.6L (7.5 pt) Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Manual Transmission and Clutch
The primary function of the clutch is to couple and uncouple engine power to the transmission upon
driver command. For additional information, refer to
Section 308 - 01 .
Clutch Disc and Clutch Pressure Plate — 3.8L
SECTION 308-
00: Manual Transaxle/Transmission and Clutch — General
Information 2003 Mustang Workshop
Manual Item Part Number Description
1 6397 Flywheel housing to block dowel (2 req'd)
2 — Rear face of block and flywheel (part of 6010)
3 6397 Flywheel to clutch pressure plate dowel (3 req'd)
4 7600 Pilot bearing
5 7550 Clutch disc
6 7563 Clutch pressure plate Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

Clutch Disc and Clutch Pressure Plate —
4.6L (4V)
z The clutch is a single plate, dry friction clutch disc. The clutch disc has a splined hub with
integral torsional springs. The clutch disc hub attaches to the input shaft.
z Engine output is coupled to the transmission input shaft by friction existing between the clutch
disc facings and the flywheel/clutch pressure plate assembly. The extent of this friction is directly related to the composition of the facing material and the magnitude of the clamping 12 7548 Clutch release hub and bearing
13 N808969-
S100 Bolt
14 N808969-
S100 Bolt (6 req'd)
15 — Rear face of block and flywheel (part of 6010)
16 — Bolt (3 req'd)
17 6397 Flywheel housing to block dowel (2 req'd)
Item Part Number Description
1 6375 Flywheel
2 7600 Pilot bearing
3 7550 Clutch disc
4 7563 Clutch pressure plate
5 7548 Clutch release hub and bearing
6 7515 Clutch release lever
7 7B602 Clutch release lever stud
8 6392 Flywheel housing
9 N808969-S100 Clutch pressure plate bolt (6 req'd) Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...