2003 FORD MUSTANG fuse box

(20A).
z Battery junction
box (BJB) fuse
12 (40A).
z Circuitry.
z GEM.
z No communication with
the instrument cluster z
Central junction
box (CJB) fuse
(s):
„11
(15A).
„ 21 (5A).
„ 34
(20A).
z Circuitry.
z Standard
corporate
protocol (SCP)
network.
z Instrument
cluster. z
Go To Pinpoint Test A .
z Incorrect fuel gauge
indication z
Circuitry.
z Fuel pump
module.
z Instrument
cluster. z
Go To Pinpoint Test B .
z Incorrect oil pressure
gauge indication z
Circuitry.
z Engine oil
pressure
switch.
z Instrument
cluster. z
Go To Pinpoint Test C .
z Incorrect temperature
gauge indication z
Circuitry.
z Engine coolant
temperature
sensor.
z Powertrain
control module
(PCM).
z Instrument
cluster. z
Go To Pinpoint Test D .
z Incorrect voltage gauge
indication— except
Cobra z
Circuitry.
z Generator.
z Standard
corporate
protocol (SCP)
network.
z Instrument
cluster. z
Go To Pinpoint Test E .
z Incorrect tachometer
indication z
Standard
corporate
protocol (SCP)
network.
z Powertrain
control module
(PCM).
z Instrument
cluster. z
Go To Pinpoint Test F .
z Incorrect boost gauge zPressure line. zGo To Pinpoint Test G . Klj . 10 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Pinpoint Tests
PINPOINT TEST A: NO COMMUNICATION WITH THE INSTRUMENT
CLUSTER z
The SERVICE ENGINE
SOON indicator is
never/always on z
Circuitry.
z SERVICE
ENGINE
SOON
indicator bulb.
z Powertrain
control module
(PCM).
z Instrument
cluster. z
Go To Pinpoint Test S .
z The turn/hazard
indicator is never/always
on z
Circuitry.
z Turn/hazard
bulb(s).
z Instrument
cluster. z
Go To Pinpoint Test T .
z The THEFT indicator is
never/always on z
Circuitry.
z THEFT
indicator LED.
z Instrument
cluster. z
REFER to Section 419 - 01 .
z The traction control
indicator is never/always
on z
Circuitry.
z Traction control
switch.
z Standard
corporate
protocol (SCP)
network.
z Powertrain
control module
(PCM).
z ABS module.
z Instrument
cluster. z
Go To Pinpoint Test U .
z The integrated circuit
display is
inoperative/erratic z
Instrument
cluster. z
Go To Pinpoint Test V .
z The instrument cluster is
inoperative z
Central junction
box (CJB) fuse
(s):
„11
(15A).
„ 21 (5A).
„ 34
(20A).
z Circuitry.
z Instrument
cluster. z
Go To Pinpoint Test V .
Test Step Result / Action to
Take Klj . 13 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Horn
Refer to Wiring Diagrams Cell
44 , Horns/Cigar Lighter for schematic and connector information.
Inspection and Verification 1. Verify the customer concern by operating the horn (13832).
2. Visually inspect for obvious signs of mechanical and electrical damage.
3. If fault is not visually evident, determine the symptom and proceed to Symptom Chart.
Symptom Chart SECTION 413-
06: Horn 2003 Mustang Workshop Manual Special Tool(s)
73 Digital Multimeter or
equivalent
105-
R0051
Visual Inspection Chart Mechanical Electrical
z
Damaged horns
z Damaged horn switch
z Damaged air bag sliding contact
(14A664) z
Blown battery junction box (BJB) Fuse Horn
Relay (20A)
z Damaged wiring harness
z Damaged connections
z Damaged horn relay
z Damaged horn switch
Symptom Chart Condition
Possible Sources Action
z The horn does not
sound z
BJB Fuse Horn Relay (20A).
z Circuitry.
z Horn relay.
z Air bag sliding contact.
z Horn switch.
z Horns. z
GO to
Pinpoint Test A .
z The horn sounds
continuously z
Circuitry.
z Horn relay.
z Remote entry system (generic
electronic module [GEM]) z
GO to
Pinpoint Test B . Klj . 1 ba
52003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

4. If the concern remains after the inspection, connect the diagnostic tool to the data link connector
(DLC) located beneath the instrument panel and select the vehicle to be tested from the
diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
zcheck that the program card is correctly installed.
z check the connections to the vehicle.
z check the ignition switch position.
5. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool manual.
6. Carry out the Data Link Diagnostic Test. If the diagnostic tool responds with: zCKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418 -
00 .
z NO RESP/NOT EQUIP for GEM, go to Pinpoint Test A.
z NO RESP/NOT EQUIP for RCM, refer to Section 501 - 20B .
z SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the GEM.
7. If the DTCs retrieved are related to the concern, go to the GEM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
8. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
9. If the DTCs retrieved are for the RCM, refer to Section 501 - 20B .
Visual Inspection Chart Mechanical Electrical
z
Switch(es) z
Central junction box (CJB) fuses:
„28 (15A)
„ 32 (15A)
„ 39 (5A)
z Circuitry
GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action
B1340 Chime Input Request
Circuit Short to Ground GEM Go To Pinpoint Test C .
B1342 ECU Is Defective GEM CLEAR the DTCs. TEST the system for normal operation.
RETRIEVE the DTCs. If DTC B1342 is retrieved, INSTALL
a new GEM. REFER to
Section 419 - 10 .
B1353 Ignition Key-
In Circuit
Open GEM Go To Pinpoint Test B .
B1462 Safety Belt Switch
Circuit Failure GEM Go To Pinpoint Test F . Klj . 3 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Symptom Chart
Symptom Chart Condition
Possible Sources Action
z No communication with the
generic electronic module
(GEM) z
Central junction box
(CJB) fuses:
„39 (5A).
„ 32 (15A).
z Circuitry.
z Generic electronic
module (GEM). z
Go To Pinpoint Test
A .
z The key- in-ignition chime does
not operate correctly z
Central junction box
(CJB) fuses:
„28 (15A).
„ 32 (15A).
z Central junction box
(CJB).
z Driver door ajar
switch.
z Key- in ignition
switch.
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
B .
z A chime does not operate
correctly— air bag z
Restraint control
module (RCM).
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
C .
z The door ajar chime does not
operate correctly z
Driver door ajar
switch.
z Passenger door ajar
switch.
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
D .
z The headlamp on reminder
chime does not operate
correctly z
Headlamp switch .
z Circuitry.
z Generic electronic
module (GEM).
z Driver door ajar
switch.
z Ignition switch. z
Go To Pinpoint Test
E .
z The safety belt warning chime
does not operate correctly z
Circuitry.
z Safety belt switch.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
F .
z The belt minder feature does
not operate correctly z
Circuitry.
z Safety belt switch.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
F . Klj . 4 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

provide ventilation.
WARNING: When lifting a plastic- cased battery, excessive pressure on the end walls
could cause acid to spew through the vent caps resulting in personal injury, damage to the
vehicle or to the battery. Lift with a battery carrier or with your hands on opposite corners.
1. Verify the customer concern by operating the engine to duplicate the concern.
2. Inspect the charging system (battery, generator cable, harness connectors, connections) to determine if any obvious mechanical or electrical concerns exist. If found, repair as necessary
and test the system for normal operation. Refer to the following tables:
3. Check the operation of the charging system warning indicator lamp (instrument cluster). Normal operation is as follows:
zWith the ignition switch OFF, the charging system warning indicator should be OFF.
z With the ignition switch in RUN and the engine off, the charging system warning indicator
light should be on.
z With the engine running, the charging system warning indicator light should be off.
4. Verify the battery is being charged. Carry out the Battery— Load Test. Refer to Component
Tests in this section.
5. If the customer concern is verified after the initial inspection, refer to the Symptom Chart to determine which tests to carry out.
Symptom Chart Visual Inspection Chart
Mechanical Electrical
z
Battery case, posts, hold- down clamp, cables and
connections
z Generator drive (serpentine) belt for condition and
tension. Refer to Section 303 - 05 .
z Generator pulley z
Battery junction box (BJB)
fuse 20 (20A)
z Fuse links
z Circuitry
z Battery charge warning
indicator
z Cables
Normal Charging System Voltages Ignition
Switch
Position A Circuit
36
(YE/WH) I Circuit
904
(LG/RD) Generator B+
Circuit 38 (BK/OG) Battery Engine to
battery
ground Charging
System Warning Indicator
Operation OFF 12V 0V 12V 12V 0V Off
RUN-
engine off 12V 1-
3V 12V 12V 0V Illuminated
RUN-
engine
running 13-
15V 13-
15V 13-
15V 13-15V 0V Off Klj . 3 ba
142003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Pinpoint Tests
CAUTION: Do not make jumper connections except as directed. Incorrect connections
may damage the voltage regulator test terminals, fuses, or fuse links.
CAUTION: Do not allow any metal object to come in contact with the generator housing
and internal diode cooling fins.
NOTE: All voltage measurements are referenced to the negative (- ) battery post unless otherwise
specified. PINPOINT TEST A: BATTERY IS DISCHARGED OR VOLTAGE IS Symptom Chart
Condition
Possible Sources Action
z Battery is discharged or voltage is
low z
Circuitry.
z High key- off current
drain(s).
z Battery.
z Generator. z
Go To Pinpoint
Test A .
z The charging system warning
indicator is on with the engine
running (the system voltage does
not increase) z
Circuitry.
z Voltage regulator.
z Generator. z
Go To Pinpoint
Test B .
z The system overcharges (the
battery voltage is greater than 15.5
volts) z
Circuitry.
z Voltage regulator.
z Generator. z
Go To Pinpoint
Test C .
z The charging system warning
indicator is on with the engine
running and the battery increases
voltage z
Circuitry.
z Instrument cluster.
z Voltage regulator.
z Generator. z
Go To Pinpoint
Test D .
z The charging system warning
indicator is off with the ignition
switch in the RUN position and the
engine off z
Bulb.
z Circuitry.
z Instrument cluster.
z Voltage regulator.
z Generator. z
Go To Pinpoint
Test E .
z The charging system warning
indicator flickers or is intermittent z
Central junction box
(CJB) fuse 5 (15A).
z Generator
connector
unplugged (C102a).
z Circuitry.
z Generator. z
Go To Pinpoint
Test F .
z The generator is noisy zBolts or brackets.
z Drive belt.
z Generator or pulley. z
Go To Pinpoint
Test G .
z Radio interference zGenerator.
z Circuitry.
z In-vehicle
entertainment
system. z
Go To Pinpoint
Test F . Klj . 4 ba
142003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST G: THE GENERATOR IS NOISY REPAIR as
necessary. TEST the
system for normal
operation.
F2 CHECK FUSE
z
Key in START position.
z With the engine running, check battery junction box (BJB) fuse 20
(20A) in circuit 36 (YE/WH) for looseness by wiggling the fuse and
noting the charging system warning indicator lamp operation.
z Does the charging system warning indicator lamp flicker? Yes
REPAIR loose fuse
connections as
necessary. TEST the
system for normal
operation.
No
GO to
F3 .
F3 CHECK A CIRCUIT 36 (YE/WH) CONNECTIONS
z
Key in OFF position.
z Connect a fused jumper wire between the generator C102c, (4.6L
4V) or C102a (3.8L or 4.6L 2V) pin 3, circuit 36 (YE/WH), harness
side and the positive battery terminal.
z Key in START position.
z With the engine running, note the charging system warning
indicator operation.
z Does the charging system warning indicator lamp flicker? Yes
REFER to
Section 414 - 02 . TEST the
system for normal
operation.
No
REPAIR loose
connection(s) in
circuits. TEST the
system for normal
operation. Test Step Result / Action to Take
G1 CHECK FOR ACCESSORY DRIVE NOISE
z
Check the accessory drive belt for damage and
correct installation. Check the accessory
mounting brackets and generator pulley for
looseness or misalignment.
z Is the accessory drive OK? Yes
GO to
G2 .
No
REPAIR as necessary. REFER to
Section 303 - 05 for diagnosis and testing
of the accessory drive system. TEST the
system for normal operation. G2 CHECK GENERATOR MOUNTING
z
Check the generator mounting for loose bolts
or misalignment.
z Is the generator mounted correctly? Yes
GO to
G3 .
No
REPAIR as necessary. TEST the system
for normal operation. G3 CHECK GENERATOR FOR ELECTRICAL Klj . 9 ba
142003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...