2003 FORD MUSTANG mirror

z
No contact with side
glass. z
ADJUST the door glass.
z No contact with glass
runs at both ends of
belt line seal. z
ADJUST the belt line seal
or ADD foam at the seal
ends.
z Belt line seal damaged. zINSTALL a new seal.
z Air leak at outer
belt line z
Belt line seal installed
incorrectly on flange
(no glass contact). z
ADJUST the seal.
z Belt line seal does not
contact the glass. z
ADJUST the door glass.
z No contact with glass
runs at both ends of
belt line seal. z
ADJUST the belt line
seal/ADD foam at the seal
ends.
z Belt line seal damaged. zINSTALL a new seal.
z Draft at inner
door
handle/speaker
opening z
Hole in watershield. zSEAL the hole with a
suitable tape.
z Watershield
misaligned. z
REALIGN the watershield.
INSTALL a new
watershield if the pressure
sensitive adhesive fails.
z Exterior door handle
seal
misaligned/damaged. z
REALIGN or INSTALL a
new seal as necessary.
z Wind noise from
side view mirror z
Outside mirror housing
misaligned. z
REALIGN with the edges
shingled correctly and no
gaps.
z Mirror sail gasket
folded/misaligned. z
REINSTALL with the
gasket unfolded and
aligned correctly.
z Mirror housing trim cap
installed incorrectly. z
REINSTALL with the
edges shingled to the air
flow.
z Air leak through mirror
housing hinge. z
Fully ENGAGE the mirror
into its operating
position/USE foam to
block the air path through
the hinge.
z Inner sail trim installed
incorrectly. z
REINSTALL the sail
trim/ADJUST the door
trim.
z Inner sail gasket/barrier
installed incorrectly. z
REINSTALL the trim
cover with the
gasket/barrier aligned
correctly.
z Air path through wiring
bundle/fastener access
holes. z
BLOCK the air path(s)
with foam/tape.
z Exposed fastener
access hole on mirror
housing/sail. z
INSTALL a new cap if it is
missing.
z Air leak around
perimeter of fixed z
Gaps in the sealant
bead. z
APPLY approved sealant. Klj . 13 ba
702003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Interior Lighting
The interior lighting system consists of the following:
zmap/dome lamp assembly
z rear- high mount/cargo lamp assembly
z dimmer switch
z door ajar switch (located on the door latches)
z rear view mirror interior lamp (convertible only)
z courtesy lamp
z vanity mirror lamp assembly
z transmission range indicator
SECTION 417-
02: Interior Lighting 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

as detected by the door ajar circuit. For vehicles equipped with the remote keyless entry feature, any
signal the GEM detects when a valid remote transmitter button is depressed will reset both the
demand and courtesy lamp battery saver timers. This battery saver relay then restores power to both
the demand and courtesy lamp circuits.
Base Courtesy and Extended Lighting
The base courtesy lighting feature provides interior lighting for the convenience of the vehicle's
occupants. The courtesy lamps consist of the map/dome lamps for the coupe and the map lamps for
the convertible. All lamps designated as courtesy lamps will be illuminated whenever the GEM detects
that the driver or passenger doors become ajar, by means of the driver or passenger door ajar circuits.
The courtesy lamps will also be illuminated when the GEM detects that the dome lamp switch has
been activated, by means of the dome lamp switch circuit.
The extended courtesy lighting feature provides temporary extended illumination of the courtesy lamps
after the customer has entered the vehicle. The courtesy lamps will remain illuminated for 25 seconds
after the GEM detects that the driver and passenger doors are closed, as detected by the door ajar
circuits. The extended courtesy lighting feature will be terminated after the 25 second time-
out period,
or if the GEM detects that the ignition switch has been moved from the OFF position to either the RUN,
ACC, or START positions.
Demand Lighting
The GEM does not provide any special features to the demand lighting group with the exception of
providing a power source when the battery saver feature is active. The demand lighting group consists
of the luggage compartment lamp, the driver and passenger vanity mirror lamps, and the map lamps.
Illuminated Entry with Remote Keyless Entry
The illuminated entry with remote keyless entry feature, provides power to the courtesy lamps when
the remote transmitter is used. When the GEM detects that the ignition switch is in the OFF or key out
positions, and it detects that a valid remote transmitter unlock button has been depressed, power to
the courtesy lamps will be enabled. The courtesy lamp circuit will remain powered until one of the
following occurs:
zThe GEM detects that the ignition switch has been moved from the OFF, to the RUN, START,
or ACC position.
z The GEM detects any valid remote transmitter lock button is depressed.
z The courtesy lamp circuit has been powered for 25 seconds.
If the GEM detects any valid remote transmitter unlock button has been depressed, and the ignition
switch is in the OFF or key out position during the 25 second time- out, the courtesy lamp circuits will
remain powered for an additional 25 seconds.
Inspection and Verification
1. The interior lighting system is a generic electronic module (GEM) controlled system.
2. Verify the customer concern by operating the interior lighting system.
3. Visually inspect for the following obvious signs of mechanical and electrical damage. Klj . 2 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST C: THE DEMAND LIGHTING IS INOPERATIVE z
Is the resistance less than 5 ohms? CLEAR the DTCs.
B21 CHECK GROUND CIRCUIT 1205 (BK) FOR OPEN
z
Measure the resistance between luggage compartment lid
switch C430 Pin 1, Circuit 1205 (BK), harness side and
ground.
z Is the resistance less than 5 ohms? Yes
INSTALL a new luggage
compartment solenoid.
For additional information,
REFER to
Section 501 -
14A . REPEAT the self-
test. CLEAR the DTCs.
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. Test Step Result / Action to Take
C1 CHECK GEM SUPPLIED POWER TO THE DEMAND LAMPS
z
Turn on both map lamps by depressing the map lamp
switches.
z Turn on both vanity mirror lamps.
z Open the luggage compartment lid.
z Do any of the lamps illuminate? Yes
GO to
C8 .
No
GO to C2 .
C2 CHECK IGNITION STATES
z
Monitor the GEM PIDS IGN_KEY, IGN_A, IGN_S, and IGN_R
while cycling the ignition switch through the OFF, ACC, RUN,
START and key out positions.
z Do the PID values agree with the ignition switch
positions? Yes
GO to
C3 .
No
For key- in-ignition
concerns, REFER to
Section 413 - 09 .
C3 CHECK DRIVER AND PASSENGER DOOR AJAR INPUTS TO
THE GEM z
Monitor the GEM PIDs D_DOOR and P_DOOR, while
opening and closing the driver and passenger doors.
z Did the GEM PIDs D_DOOR and P_DOOR agree with the
driver and passenger door positions? Yes
GO to
C4 .
No
REFER to Section 413 -
09 . Klj . 12 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

C4 CHECK INTERIOR LAMP SWITCH INPUT TO THE GEM —
MONITOR GEM PID DOMESW z
Monitor the GEM PID DOMESW, while moving the interior
lamp switch from the OFF to the ON position.
z Does the GEM PID DOMESW values agree with the
interior lamp switch positions? Yes
GO to
C5 .
No
GO to Pinpoint Test B .
C5 CHECK THE LUGGAGE COMPARTMENT LID AJAR INPUT
TO THE GEM — MONITOR THE GEM PID DECKLID z
Monitor the GEM PID DECKLID, while opening, and closing,
the luggage compartment lid.
z Does the GEM PID DECKLID agree with the luggage
compartment lid position? Yes
GO to
C6 .
No
GO to Pinpoint Test B .
C6 CHECK CIRCUIT 705 (LG/OG) FOR OPEN
z
Turn on both map lamps using the switches in the rear view
mirror.
z Turn on both vanity mirror lamps.
z Open the luggage compartment lid.
z Disconnect: GEM C201c.
z Connect a fused jumper (20A) between GEM C201c Pin 4,
Circuit 705 (LG/OG), harness side and battery positive
terminal.
z Do the demand lamps illuminate? Yes
GO to
C7 .
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. C7 CHECK CIRCUIT 1006 (DG/WH) FOR OPEN
NOTE:
Verify battery voltage at CJB Fuse 7 (20A) before
carrying out this test.
z Disconnect: GEM C201a.
z Measure the voltage between GEM C201a Pin 1, Circuit 1006
(DG/WH), harness side and ground.
z Is the voltage greater than 10 volts? Yes
INSTALL a new GEM. For
additional information,
REFER to
Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs.
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. C8 CHECK CIRCUIT 705 (LG/OG) FOR VOLTAGE AT
INOPERATIVE DEMAND LAMP z
Key in OFF position.
z Disconnect inoperative demand lamp, dome/map C929 Yes
GO to
C9 . Klj . 13 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Trim Panel —
Door
Removal
All vehicles
1. CAUTION: Use a shop towel or similar material between the tool and the front door
trim panel or damage to the front door trim panel may occur.
Position the window regulator switch plate (14527) aside. 1. Pull at the service notch.
2. Lift to release the clip at the rear edge.
2. Remove the window regulator switch plate. 1. Disconnect the power mirror electrical connector.
2. Remove the screws and the window regulator switch plate.
3. Remove the door latch release handle cup (22634).
SECTION 501-
05: Interior Trim and Ornamentation 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

SPECIFICATIONS
SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Torque Specifications
Description Nm lb-
ft lb-
in Exterior rear view mirror nuts 12 9 —
Exterior rear view mirror motor screws 7 — 62 Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Rear View Mirrors
The rear view mirror system consists of the following components:
zexterior rear view mirror
z exterior rear view mirror control
z exterior rear view mirror glass
z exterior rear view mirror motor
z interior rear view mirror
z exterior rear view mirror (Cobra) (manual folding)
SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...