2003 DODGE RAM map sensor

VACUUM ASSIST
The PCM cannot detect leaks or restrictions in the
vacuum circuits of vacuum assisted engine control
system devices. However, these could cause the PCM
to store a MAP sensor diagnostic trouble code and
cause a high idle condition.
PCM SYSTEM GROUND
The PCM cannot determine a poor system ground.
However, one or more diagnostic trouble codes maybe generated as a result of this condition. The mod-
ule should be mounted to the body at all times, also
during diagnostic.
PCM CONNECTOR ENGAGEMENT
The PCM may not be able to determine spread or
damaged connector pins. However, it might store
diagnostic trouble codes as a result of spread connec-
tor pins.
DREMISSIONS CONTROL 25 - 9
EMISSIONS CONTROL (Continued)

ABS - DESCRIPTION, BRAKES...........5-39
ABS - OPERATION, BRAKES.............5-39
ABS BRAKE BLEEDING - STANDARD
PROCEDURE.........................5-40
ABS INDICATOR - DESCRIPTION.........8J-17
ABS INDICATOR - OPERATION..........8J-17
A/C APPLICATION TABLE,
SPECIFICATIONS......................24-7
A/C COMPRESSOR CLUTCH -
DESCRIPTION........................24-9
A/C COMPRESSOR CLUTCH -
INSPECTION........................24-12
A/C COMPRESSOR CLUTCH -
INSTALLATION.......................24-12
A/C COMPRESSOR CLUTCH -
OPERATION..........................24-9
A/C COMPRESSOR CLUTCH - REMOVAL . . 24-10
A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-10
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-10
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-13
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-14
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-13
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-14
A/C COMPRESSOR NOISE - DIAGNOSIS
AND TESTING.......................24-36
A/C CONDENSER - DESCRIPTION.........24-39
A/C CONDENSER - OPERATION..........24-39
A/C EVAPORATOR - DESCRIPTION.......24-47
A/C EVAPORATOR - INSTALLATION......24-47
A/C EVAPORATOR - OPERATION.........24-47
A/C EVAPORATOR - REMOVAL..........24-47
A/C HEATER CONTROL - DESCRIPTION . . . 24-14
A/C HEATER CONTROL - INSTALLATION . . . 24-15
A/C HEATER CONTROL - REMOVAL......24-14
A/C ORIFICE TUBE - DESCRIPTION.......24-48
A/C ORIFICE TUBE - INSTALLATION......24-49
A/C ORIFICE TUBE - OPERATION........24-48
A/C ORIFICE TUBE - REMOVAL..........24-49
A/C PERFORMANCE - DIAGNOSIS AND
TESTING............................24-2
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-15
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-15
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-16
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-15
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-16
ACCELERATOR PEDAL - INSTALLATION . . . 14-24
ACCELERATOR PEDAL - REMOVAL.......14-24
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION...............14-25
ACCELERATOR PEDAL POSITION
SENSOR - INSTALLATION..............14-25
ACCELERATOR PEDAL POSITION
SENSOR - OPERATION................14-25
ACCELERATOR PEDAL POSITION
SENSOR - REMOVAL..................14-25
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING................7-25,7-28,7-31
ACCUMULATOR - DESCRIPTION.........24-49
ACCUMULATOR - DESCRIPTION
. . 21-191,21-372
ACCUMULATOR - INSPECTION
. . . 21-192,21-373
ACCUMULATOR - INSTALLATION
........24-50
ACCUMULATOR - OPERATION
..........24-49
ACCUMULATOR - OPERATION
....21-192,21-373
ACCUMULATOR - REMOVAL
............24-49
ACM COVER - INSTALLATION
............8O-9
ACM COVER - REMOVAL
...............8O-9
ACTUATION TEST MODE - DESCRIPTION,
CIRCUIT
.............................25-1
ACTUATOR - DESCRIPTION, BLEND
DOOR
.............................24-16
ACTUATOR - DESCRIPTION, FUEL
CONTROL
..........................14-85
ACTUATOR - DESCRIPTION, MODE
DOOR
.............................24-20
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR
................24-22ACTUATOR - INSTALLATION, BLEND
DOOR.............................24-17
ACTUATOR - INSTALLATION, FLOOR -
DEFROST DOOR.....................24-20
ACTUATOR - INSTALLATION, FUEL
CONTROL..........................14-85
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-22,23-32
ACTUATOR - INSTALLATION, MODE
DOOR.............................24-22
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-23
ACTUATOR - OPERATION, BLEND DOOR . . 24-16
ACTUATOR - OPERATION, FUEL
CONTROL..........................14-85
ACTUATOR - OPERATION, MODE DOOR . . . 24-21
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-22
ACTUATOR - REMOVAL, BLEND DOOR....24-17
ACTUATOR - REMOVAL, FLOOR -
DEFROST DOOR.....................24-19
ACTUATOR - REMOVAL, FUEL CONTROL . . 14-85
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-22,
23-31
ACTUATOR - REMOVAL, MODE DOOR....24-21
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-22
ADAPTER HOUSING SEAL -
INSTALLATION...........21-127,21-539,21-83
ADAPTER HOUSING SEAL - REMOVAL . . 21-127,
21-539,21-83
ADAPTER MOUNT - INSTALLATION, DISC
BRAKE CALIPER......................5-17
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-19
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-19
ADHESIVE LOCATIONS -
SPECIFICATIONS, STRUCTURAL........23-113
ADJUSTABLE PEDAL MOTOR -
DESCRIPTION........................5-24
ADJUSTABLE PEDAL MOTOR -
INSTALLATION........................5-24
ADJUSTABLE PEDAL MOTOR - REMOVAL . . 5-24
ADJUSTABLE PEDAL SWITCH -
INSTALLATION.........................5-6
ADJUSTABLE PEDAL SWITCH -
REMOVAL............................5-6
ADJUSTER - DIAGNOSIS AND TESTING,
HYDRAULIC LASH................9-124,9-31
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-50
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-50
ADJUSTER ASSEMBLY - DESCRIPTION,
ROCKER ARM.......................9-124
ADJUSTER ASSEMBLY - INSTALLATION,
ROCKER ARM..................9-124,9-249
ADJUSTER ASSEMBLY - REMOVAL,
ROCKER ARM..................9-124,9-249
ADJUSTER ASSY - CLEANING, ROCKER
ARM
..............................9-310
ADJUSTER ASSY - DESCRIPTION,
ROCKER ARM
.......................9-310
ADJUSTER ASSY - INSPECTION,
ROCKER ARM
.......................9-311
ADJUSTER ASSY - INSTALLATION,
ROCKER ARM
.............9-198,9-312,9-379
ADJUSTER ASSY - REMOVAL, ROCKER
ARM
....................9-198,9-310,9-379
ADJUSTING TOOL - ADJUSTMENT, WITH
. . . 5-36
AFTER A SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE
.................8O-7
AIR CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING
..........................21-494
AIR CLEANER ELEMENT - INSTALLATION
. 9-105,
9-20,9-242,9-298,9-370
AIR CLEANER ELEMENT - REMOVAL
. 9-105,9-20,
9-242,9-297,9-370
AIR CONDITIONER - DESCRIPTION,
HEATER
.............................24-1
AIR CONDITIONER - OPERATION,
HEATER
.............................24-1
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE WITH
.......7-70AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE
WITHOUT............................7-70
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITH.............7-68
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITHOUT..........7-69
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-33
AIR CONTROL MOTOR - INSTALLATION,
IDLE...............................14-35
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-33
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-34
AIR COOLER AND PLUMBING -
CLEANING, CHARGE..................11-16
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE...............11-15
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-16
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE...............11-16
AIR COOLER AND PLUMBING -
OPERATION, CHARGE.................11-15
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE..................11-15
AIR COOLER SYSTEM - LEAKS -
DIAGNOSIS AND TESTING, CHARGE......11-15
AIR DAM - INSTALLATION, FRONT........13-2
AIR DAM - REMOVAL, FRONT...........13-2
AIR HEATER - DESCRIPTION, INTAKE.....14-91
AIR HEATER - INSTALLATION, INTAKE....14-91
AIR HEATER - OPERATION, INTAKE......14-91
AIR HEATER - REMOVAL, INTAKE........14-91
AIR HEATER RELAY - DESCRIPTION,
INTAKE ............................14-92
AIR HEATER RELAY - INSTALLATION,
INTAKE ............................14-93
AIR HEATER RELAY - OPERATION,
INTAKE ............................14-92
AIR HEATER RELAY - REMOVAL, INTAKE . . 14-93
AIR INTAKE SYSTEM - INSTALLATION....9-194
AIR INTAKE SYSTEM - REMOVAL........9-194
AIR TEMPERATURE SENSOR -
DESCRIPTION, INTAKE................14-36
AIR TEMPERATURE SENSOR -
INSTALLATION, INTAKE................14-38
AIR TEMPERATURE SENSOR -
OPERATION, INTAKE..................14-36
AIR TEMPERATURE SENSOR -
REMOVAL, INTAKE...................14-36
AIR TEMPERATURE SENSOR/MAP
SENSOR - DESCRIPTION, INTAKE........14-93
AIR TEMPERATURE SENSOR/MAP
SENSOR - INSTALLATION, INTAKE.......14-94
AIR TEMPERATURE SENSOR/MAP
SENSOR - OPERATION, INTAKE.........14-93
AIR TEMPERATURE SENSOR/MAP
SENSOR - REMOVAL, INTAKE...........14-93
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - DESCRIPTION, INLET.........14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - INSTALLATION, INLET........14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - OPERATION, INLET..........14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - REMOVAL, INLET............14-90
AIR TESTING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-143,21-324
AIR TO OIL COOLER - INSTALLATION.....7-75
AIR TO OIL COOLER - REMOVAL.........7-74
AIRBAG - DESCRIPTION, DRIVER........8O-22
AIRBAG - DESCRIPTION, PASSENGER....8O-34
AIRBAG - DESCRIPTION, SIDE CURTAIN . . 8O-51
AIRBAG - INSTALLATION, DRIVER.......8O-24
AIRBAG - INSTALLATION, PASSENGER . . . 8O-37
AIRBAG - INSTALLATION, SIDE CURTAIN . . 8O-53
AIRBAG - OPERATION, DRIVER.........8O-23
AIRBAG - OPERATION, PASSENGER......8O-35
AIRBAG - OPERATION, SIDE CURTAIN....8O-51
AIRBAG - REMOVAL, DRIVER
...........8O-23
AIRBAG - REMOVAL, PASSENGER
.......8O-35
AIRBAG - REMOVAL, SIDE CURTAIN
.....8O-52
AIRBAG CONTROL MODULE -
DESCRIPTION
.......................8O-10
AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE IMPACT
...........8O-53
DRINDEX 1
Description Group-Page Description Group-Page Description Group-Page

INDICATOR - DESCRIPTION, UPSHIFT....8J-40
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-42
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-42
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-43
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-19
INDICATOR - OPERATION, ABS..........8J-17
INDICATOR - OPERATION, AIRBAG.......8J-18
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-19
INDICATOR - OPERATION, CARGO LAMP . . 8J-20
INDICATOR - OPERATION, CHECK
GAUGES............................8J-21
INDICATOR - OPERATION, CRUISE.......8J-22
INDICATOR - OPERATION, DOOR AJAR . . . 8J-23
INDICATOR - OPERATION, ETC..........8J-25
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-27
INDICATOR - OPERATION, HIGH BEAM....8J-28
INDICATOR - OPERATION, LAMP OUT....8J-28
INDICATOR - OPERATION, LOW FUEL.....8J-29
INDICATOR - OPERATION, OVERDRIVE
OFF ...............................8J-33
INDICATOR - OPERATION, SEATBELT.....8J-34
INDICATOR - OPERATION, SECURITY.....8J-35
INDICATOR - OPERATION, SERVICE 4WD . . 8J-36
INDICATOR - OPERATION, TRANS TEMP . . 8J-38
INDICATOR - OPERATION, TURN SIGNAL . . 8J-39
INDICATOR - OPERATION, UPSHIFT......8J-40
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-42
INDICATOR - OPERATION, WASHER
FLUID..............................8J-42
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-43
INDICATOR LAMP - DESCRIPTION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP - OPERATION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-30
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-30
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-7
INERTIA HINGE COVER - INSTALLATION,
CENTER SEAT BACK..................23-78
INERTIA HINGE COVER - REMOVAL,
CENTER SEAT BACK..................23-78
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-6
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE................8M-10
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-8
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE...........................8M-10
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-39
INITIALIZATION, STANDARD PROCEDURE
- SENTRY KEY IMMOBILIZER SYSTEM....8Q-3
INJECTION PUMP - DESCRIPTION, FUEL . . 14-64
INJECTION PUMP - INSTALLATION, FUEL . 14-67
INJECTION PUMP - OPERATION, FUEL
....14-64
INJECTION PUMP - REMOVAL, FUEL
.....14-65
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL
..................14-65
INJECTOR - DESCRIPTION, FUEL
. . . 14-32,14-85
INJECTOR - INSTALLATION, FUEL
........14-87
INJECTOR - OPERATION, FUEL
.....14-32,14-86
INJECTOR - REMOVAL, FUEL
...........14-87
INJECTOR FIRING ORDER, DIESEL -
FUEL
..............................14-60
INJECTOR RAIL - DESCRIPTION, FUEL
....14-89
INJECTOR RAIL - INSTALLATION, FUEL
. . . 14-90
INJECTOR RAIL - OPERATION, FUEL
.....14-89
INJECTOR RAIL - REMOVAL, FUEL
.......14-89
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - DESCRIPTION
.....14-90INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - INSTALLATION.....14-90
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - OPERATION.......14-90
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - REMOVAL........14-90
INLET FILTER - INSTALLATION..........14-23
INLET FILTER - REMOVAL..............14-23
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
INNER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
INNER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
INNER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-6
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-552
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-549
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-550
INPUT CLUTCH ASSEMBLY - OPERATION . 21-549
INPUT SHAFT SEAL - INSTALLATION,
STEERING GEAR.....................19-28
INPUT SHAFT SEAL - REMOVAL,
STEERING GEAR.....................19-25
INPUT SPEED SENSOR - DESCRIPTION . . 21-558
INPUT SPEED SENSOR - INSTALLATION . 21-559
INPUT SPEED SENSOR - OPERATION....21-558
INPUT SPEED SENSOR - REMOVAL.......21-559
INSERTS - INSTALLATION, SPRING TIP....2-42
INSERTS - REMOVAL, SPRING TIP........2-41
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-22,23-32
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-22,
23-31
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-384
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-384
INSTRUMENT CLUSTER - ASSEMBLY.....8J-15
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING.......................8J-10
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-14
INSTRUMENT CLUSTER - INSTALLATION . . 8J-16
INSTRUMENT CLUSTER - OPERATION.....8J-6
INSTRUMENT CLUSTER - REMOVAL.....8J-14
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-7
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-6
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-56
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-53
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-58
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-58
INSTRUMENT PANEL DRIVER SIDE
BEZEL - INSTALLATION................23-59
INSTRUMENT PANEL DRIVER SIDE
BEZEL - REMOVAL...................23-58
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-29
INSTRUMENT PANEL DUCTS - REMOVAL . 24-29
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - INSTALLATION.........23-57
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - REMOVAL............23-57
INSTRUMENT PANEL LOWER
SURROUND - INSTALLATION...........23-60
INSTRUMENT PANEL LOWER
SURROUND - REMOVAL...............23-60
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-60
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-59
INTAKE AIR HEATER - DESCRIPTION.....14-91
INTAKE AIR HEATER - INSTALLATION
.....14-91
INTAKE AIR HEATER - OPERATION
.......14-91
INTAKE AIR HEATER - REMOVAL
........14-91
INTAKE AIR HEATER RELAY -
DESCRIPTION
.......................14-92
INTAKE AIR HEATER RELAY -
INSTALLATION
.......................14-93INTAKE AIR HEATER RELAY -
OPERATION.........................14-92
INTAKE AIR HEATER RELAY - REMOVAL . . 14-93
INTAKE AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-36
INTAKE AIR TEMPERATURE SENSOR -
INSTALLATION.......................14-38
INTAKE AIR TEMPERATURE SENSOR -
OPERATION.........................14-36
INTAKE AIR TEMPERATURE SENSOR -
REMOVAL..........................14-36
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - DESCRIPTION..........14-93
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - INSTALLATION..........14-94
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - OPERATION............14-93
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - REMOVAL.............14-93
INTAKE MANIFOLD - CLEANING....9-158,9-219,
9-275,9-346,9-402
INTAKE MANIFOLD - DESCRIPTION . 9-157,9-219,
9-274,9-401,9-71
INTAKE MANIFOLD - INSPECTION . . 9-158,9-219,
9-275,9-346,9-402
INTAKE MANIFOLD - INSTALLATION.....9-158,
9-219,9-275,9-346,9-402,9-72
INTAKE MANIFOLD - OPERATION........9-274
INTAKE MANIFOLD - REMOVAL....9-157,9-219,
9-275,9-345,9-401,9-72
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING . . . 9-157,9-219,9-274,
9-401
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-71
INTAKE SYSTEM - INSTALLATION, AIR....9-194
INTAKE SYSTEM - REMOVAL, AIR.......9-194
INTAKE/EXHAUST VALVES & SEATS -
CLEANING..........................9-248
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION....9-122,9-246,9-27,9-305,9-375
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION........................9-248
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..............9-123,9-248,9-29
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.................9-122,9-248,9-28
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-3
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-4
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-3
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-3
INTERIOR - CAUTION.................23-63
INTERLOCK - ADJUSTMENTS, BRAKE
TRANSMISSION SHIFT . . . 21-195,21-376,21-540
INTERLOCK - DIAGNOSIS AND TESTING,
BRAKE TRANSMISSION SHIFT . . . 21-195,21-375,
21-540
INTERLOCK SYSTEM - DESCRIPTION,
BRAKE TRANSMISSION SHIFT . . . 21-194,21-375,
21-540
INTERLOCK SYSTEM - OPERATION,
BRAKE TRANSMISSION SHIFT . . . 21-194,21-375,
21-540
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-6
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.....9-178,9-225,
9-353,9-4,9-93
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-7
IOD FUSE - DESCRIPTION...........8W-97-6
IOD FUSE - INSTALLATION...........8W-97-7
IOD FUSE - OPERATION.............8W-97-6
IOD FUSE - REMOVAL..............8W-97-6
ISO FLARING - STANDARD PROCEDURE....5-7
ISOLATORS - INSTALLATION, BODY
......23-37
ISOLATORS - REMOVAL, BODY
.........23-36
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL
........................2-18
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL
.........................2-26
JOINT - INSTALLATION, LOWER BALL
. 2-19,2-33
18 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

MANUAL TRANSMISSION -
DESCRIPTION.........................0-4
MANUAL TRANSMISSION - NV3500 -
ASSEMBLY..........................21-17
MANUAL TRANSMISSION - NV3500 -
CLEANING..........................21-15
MANUAL TRANSMISSION - NV3500 -
DESCRIPTION........................21-1
MANUAL TRANSMISSION - NV3500 -
DIAGNOSIS AND TESTING..............21-3
MANUAL TRANSMISSION - NV3500 -
DISASSEMBLY........................21-4
MANUAL TRANSMISSION - NV3500 -
INSPECTION........................21-15
MANUAL TRANSMISSION - NV3500 -
INSTALLATION.......................21-38
MANUAL TRANSMISSION - NV3500 -
OPERATION..........................21-1
MANUAL TRANSMISSION - NV3500 -
REMOVAL...........................21-3
MANUAL TRANSMISSION - NV3500 -
SPECIAL TOOLS.....................21-40
MANUAL TRANSMISSION - NV3500 -
SPECIFICATIONS.....................21-39
MANUAL TRANSMISSION - NV4500 -
ASSEMBLY..........................21-61
MANUAL TRANSMISSION - NV4500 -
CLEANING..........................21-60
MANUAL TRANSMISSION - NV4500 -
DESCRIPTION.......................21-42
MANUAL TRANSMISSION - NV4500 -
DIAGNOSIS AND TESTING.............21-43
MANUAL TRANSMISSION - NV4500 -
DISASSEMBLY........................21-44
MANUAL TRANSMISSION - NV4500 -
INSPECTION........................21-60
MANUAL TRANSMISSION - NV4500 -
INSTALLATION.......................21-77
MANUAL TRANSMISSION - NV4500 -
OPERATION.........................21-42
MANUAL TRANSMISSION - NV4500 -
REMOVAL..........................21-43
MANUAL TRANSMISSION - NV4500 -
SPECIAL TOOLS.....................21-79
MANUAL TRANSMISSION - NV4500 -
SPECIFICATIONS.....................21-79
MANUAL TRANSMISSION - NV5600 -
ASSEMBLY.........................21-105
MANUAL TRANSMISSION - NV5600 -
DESCRIPTION.......................21-87
MANUAL TRANSMISSION - NV5600 -
DIAGNOSIS AND TESTING.............21-89
MANUAL TRANSMISSION - NV5600 -
DISASSEMBLY.......................21-90
MANUAL TRANSMISSION - NV5600 -
INSPECTION.......................21-104
MANUAL TRANSMISSION - NV5600 -
INSTALLATION......................21-120
MANUAL TRANSMISSION - NV5600 -
OPERATION.........................21-89
MANUAL TRANSMISSION - NV5600 -
REMOVAL..........................21-89
MANUAL TRANSMISSION - NV5600 -
SPECIAL TOOLS....................21-122
MAP SENSOR - DESCRIPTION.....14-39,14-94
MAP SENSOR - INSTALLATION..........14-42
MAP SENSOR - OPERATION............14-39
MAP SENSOR - REMOVAL.............14-40
MASTER CYLINDER - DESCRIPTION......5-19
MASTER CYLINDER - OPERATION........5-20
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-20
MASTER CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING..............5-20
MATCH MOUNTING - STANDARD
PROCEDURE.........................22-3
MATCHING TIRE - DESCRIPTION, FULL
SIZE, SPARE WHEEL WITH.............22-15
MATS - INSTALLATION, CARPETS AND
FLOOR
.............................23-66
MATS - REMOVAL, CARPETS AND
FLOOR
.............................23-66
MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE, HEIGHT
.........2-3
MEASURING TIMING CHAIN STRETCH -
INSPECTION
...................9-279,9-405
MEASURING TIMING CHAIN WEAR -
STANDARD PROCEDURE
...............9-165MEASURING TIMING CHAIN WEAR,
STANDARD PROCEDURE................9-76
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.....9-181,9-184,
9-228,9-283,9-356,9-6,9-91
MECHANISM - DESCRIPTION, SHIFT....21-253,
21-430,21-574
MECHANISM - INSTALLATION, SHIFT.....21-85
MECHANISM - OPERATION, SHIFT......21-253,
21-430,21-574
MECHANISM - REMOVAL, SHIFT........21-84
MEMBER BUSHING - INSTALLATION,
TORSION BAR CROSS..................2-14
METRIC SYSTEM - DESCRIPTION......Intro.-9
MICRO 420 BATTERY TESTER -
STANDARD PROCEDURE, USING........8F-12
MICRO RELAY - DESCRIPTION........8W-97-9
MICRO RELAY - INSTALLATION......8W-97-10
MICRO RELAY - OPERATION.........8W-97-9
MICRO RELAY - REMOVAL..........8W-97-10
MICRO-RELAY - DIAGNOSIS AND
TESTING.........................8W-97-9
MILE, SPECIFICATIONS - TIRE
REVOLUTIONS PER...................22-10
MINI-TRIP COMPUTER - DIAGNOSIS
AND TESTING, COMPASS..............8M-7
MIRROR - DESCRIPTION, AUTOMATIC
DAY / NIGHT........................8N-12
MIRROR - DIAGNOSIS AND TESTING,
AUTOMATIC DAY / NIGHT..............8N-12
MIRROR - INSTALLATION, SIDE VIEW....23-41
MIRROR - OPERATION, AUTOMATIC DAY
/ NIGHT............................8N-12
MIRROR - REMOVAL, AUTOMATIC DAY /
NIGHT.............................8N-13
MIRROR - REMOVAL, REAR VIEW.......23-71
MIRROR - REMOVAL, SIDE VIEW........23-41
MIRROR - REMOVAL, SIDEVIEW........8N-13
MIRROR FLAG - INSTALLATION, SIDE
VIEW..............................23-27
MIRROR FLAG - REMOVAL, SIDE VIEW . . . 23-27
MIRROR GLASS - INSTALLATION, SIDE
VIEW..............................23-44
MIRROR GLASS - REMOVAL, SIDE VIEW . . 23-42
MIRROR SUPPORT BRACKET -
INSTALLATION, REARVIEW.............23-71
MIRROR SWITCH - DIAGNOSIS AND
TESTING, POWER....................8N-13
MIRROR SWITCH - REMOVAL, POWER . . . 8N-13
MIRROR SYSTEM - DESCRIPTION,
HEATED.............................8G-1
MIRROR SYSTEM - DIAGNOSIS AND
TESTING, HEATED.....................8G-2
MIRROR SYSTEM - OPERATION, HEATED . . 8G-1
MIRRORS - DESCRIPTION, POWER......8N-11
MIRRORS - DIAGNOSIS AND TESTING,
POWER............................8N-11
MIRRORS - OPERATION, POWER........8N-11
MODE - DESCRIPTION, CIRCUIT
ACTUATION TEST.....................25-1
MODE - DESCRIPTION, STATE DISPLAY
TEST...............................25-1
MODE DOOR ACTUATOR - DESCRIPTION . . 24-20
MODE DOOR ACTUATOR -
INSTALLATION.......................24-22
MODE DOOR ACTUATOR - OPERATION . . . 24-21
MODE DOOR ACTUATOR - REMOVAL.....24-21
MODE SENSOR - DESCRIPTION
. . 21-684,21-718
MODE SENSOR - OPERATION
....21-684,21-718
MODES OF OPERATION - DESCRIPTION
....8E-8
MODES, STANDARD PROCEDURE -
CONFIGURING A NEW MODULE /
SWITCH OPERATING
...................8Q-3
MODULE - DESCRIPTION, AIRBAG
CONTROL
..........................8O-10
MODULE - DESCRIPTION, DRIVER DOOR
. . 8N-5
MODULE - DESCRIPTION, FRONT
CONTROL
........................8W-97-4
MODULE - DESCRIPTION, FRONT
CONTROL
...........................8E-5
MODULE - DESCRIPTION, FUEL PUMP
....14-12
MODULE - DESCRIPTION, FUEL TANK
....14-75
MODULE - DESCRIPTION, HEATED SEAT
. . . 8E-6
MODULE - DESCRIPTION, INTEGRATED
POWER
..........................8W-97-3
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY
......................8N-7MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-13
MODULE - DESCRIPTION, SIDE IMPACT
AIRBAG CONTROL...................8O-53
MODULE - DESCRIPTION, TRANSFER
CASE CONTROL......................8E-15
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-19
MODULE - DESCRIPTION, WIPER.......8R-22
MODULE - DIAGNOSIS AND TESTING,
DRIVER DOOR.......................8N-6
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL..................8W-97-5
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-6
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8E-7
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY..............8N-8
MODULE - INSTALLATION, AIRBAG
CONTROL..........................8O-12
MODULE - INSTALLATION, DRIVER
DOOR..............................8N-7
MODULE - INSTALLATION, ENGINE
CONTROL...........................8E-5
MODULE - INSTALLATION, FRONT
CONTROL........................8W-97-5
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-6
MODULE - INSTALLATION, FUEL PUMP . . . 14-13
MODULE - INSTALLATION, FUEL TANK....14-75
MODULE - INSTALLATION, HEATED SEAT . . . 8E-7
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-4
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY......................8N-8
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-15
MODULE - INSTALLATION, WIPER.......8R-23
MODULE - OPERATION, AIRBAG
CONTROL..........................8O-10
MODULE - OPERATION, DRIVER DOOR....8N-5
MODULE - OPERATION, FRONT
CONTROL........................8W-97-5
MODULE - OPERATION, FRONT
CONTROL...........................8E-5
MODULE - OPERATION, FUEL PUMP.....14-12
MODULE - OPERATION, FUEL TANK......14-75
MODULE - OPERATION, HEATED SEAT.....8E-6
MODULE - OPERATION, INTEGRATED
POWER..........................8W-97-3
MODULE - OPERATION, REMOTE
KEYLESS ENTRY......................8N-8
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER.......................8E-13
MODULE - OPERATION, SIDE IMPACT
AIRBAG CONTROL...................8O-54
MODULE - OPERATION, TRANSFER CASE
CONTROL..........................8E-15
MODULE - OPERATION, TRANSMISSION
CONTROL..........................8E-19
MODULE - OPERATION, WIPER.........8R-23
MODULE - REMOVAL, AIRBAG CONTROL . 8O-11
MODULE - REMOVAL, DRIVER DOOR.....8N-7
MODULE - REMOVAL, ENGINE CONTROL . . . 8E-4
MODULE - REMOVAL, FRONT CONTROL . 8W-97-5
MODULE - REMOVAL, FRONT CONTROL . . . 8E-6
MODULE - REMOVAL, FUEL PUMP.......14-12
MODULE - REMOVAL, FUEL TANK.......14-75
MODULE - REMOVAL, HEATED SEAT......8E-7
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-3
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY..............................8N-8
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER.......................8E-15
MODULE - REMOVAL, WIPER...........8R-23
MODULE / SWITCH OPERATING MODES,
STANDARD PROCEDURE -
CONFIGURING A NEW
.................8Q-3
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE
...............8M-3
MODULE LENS REPLACEMENT -
STANDARD PROCEDURE
...............8M-3
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT
...................23-93
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT
...................23-93
DRINDEX 21
Description Group-Page Description Group-Page Description Group-Page

SEAT BELT & RETRACTOR - REMOVAL,
REAR OUTBOARD....................8O-41
SEAT BELT BUCKLE - INSTALLATION,
FRONT OUTBOARD...................8O-34
SEAT BELT BUCKLE - REMOVAL, FRONT
OUTBOARD.........................8O-33
SEAT BELT SWITCH - DESCRIPTION.....8O-46
SEAT BELT SWITCH - DIAGNOSIS AND
TESTING...........................8O-47
SEAT BELT SWITCH - OPERATION.......8O-46
SEAT BELT TENSION REDUCER -
DESCRIPTION.......................8O-48
SEAT BELT TENSION REDUCER -
DIAGNOSIS AND TESTING.............8O-49
SEAT BELT TENSION REDUCER -
OPERATION.........................8O-49
SEAT BELT TENSIONER - DESCRIPTION . . . 8O-47
SEAT BELT TENSIONER - OPERATION....8O-48
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-50
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-50
SEAT CUSHION / COVER - FRONT -
INSTALLATION.......................23-83
SEAT CUSHION / COVER - FRONT -
REMOVAL..........................23-83
SEAT CUSHION / COVER - REAR -
INSTALLATION.......................23-85
SEAT CUSHION / COVER - REAR -
REMOVAL..........................23-85
SEAT CUSHION - INSTALLATION,
CENTER............................23-80
SEAT CUSHION - REMOVAL, CENTER.....23-80
SEAT CUSHION COVER - INSTALLATION,
CENTER............................23-81
SEAT CUSHION COVER - REMOVAL,
CENTER............................23-81
SEAT CUSHION FRAME - REAR -
INSTALLATION.......................23-85
SEAT CUSHION FRAME - REAR -
REMOVAL..........................23-85
SEAT ELEMENT - DESCRIPTION, HEATED . . 8G-5
SEAT ELEMENT - DIAGNOSIS AND
TESTING, HEATED.....................8G-6
SEAT ELEMENT - INSTALLATION,
HEATED.............................8G-6
SEAT ELEMENT - OPERATION, HEATED....8G-6
SEAT ELEMENT - REMOVAL, HEATED.....8G-6
SEAT MODULE - DESCRIPTION, HEATED . . . 8E-6
SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED.....................8E-7
SEAT MODULE - INSTALLATION, HEATED . . . 8E-7
SEAT MODULE - OPERATION, HEATED.....8E-6
SEAT MODULE - REMOVAL, HEATED......8E-7
SEAT SENSOR - DESCRIPTION, HEATED . . . 8G-7
SEAT SENSOR - DIAGNOSIS AND
TESTING, HEATED.....................8G-7
SEAT SENSOR - OPERATION, HEATED.....8G-7
SEAT SENSOR - REMOVAL, HEATED......8G-7
SEAT STORAGE BIN - INSTALLATION,
UNDER............................23-81
SEAT STORAGE BIN - REMOVAL, UNDER . . 23-81
SEAT STORAGE BIN COVERING -
INSTALLATION, UNDER................23-81
SEAT STORAGE BIN COVERING -
REMOVAL, UNDER...................23-81
SEAT STORAGE BIN LATCH -
INSTALLATION, UNDER................23-81
SEAT STORAGE BIN LATCH - REMOVAL,
UNDER............................23-81
SEAT SWITCH - DESCRIPTION, DRIVER . . . 8N-15
SEAT SWITCH - DESCRIPTION, HEATED . . . 8G-7
SEAT SWITCH - DESCRIPTION,
PASSENGER........................8N-16
SEAT SWITCH - DIAGNOSIS AND
TESTING, DRIVER....................8N-15
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED.....................8G-8
SEAT SWITCH - DIAGNOSIS AND
TESTING, PASSENGER................8N-17
SEAT SWITCH - INSTALLATION, DRIVER . . 8N-16
SEAT SWITCH - INSTALLATION, HEATED
. . . 8G-9
SEAT SWITCH - INSTALLATION,
PASSENGER
........................8N-18
SEAT SWITCH - OPERATION, DRIVER
....8N-15
SEAT SWITCH - OPERATION, HEATED
.....8G-8
SEAT SWITCH - OPERATION,
PASSENGER
........................8N-17SEAT SWITCH - REMOVAL, DRIVER......8N-16
SEAT SWITCH - REMOVAL, HEATED.......8G-9
SEAT SWITCH - REMOVAL, PASSENGER . . 8N-17
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-3
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED.....................8G-4
SEAT SYSTEM - DIAGNOSIS AND
TESTING, POWER....................8N-14
SEAT SYSTEM - OPERATION, HEATED.....8G-4
SEAT TRACK - DESCRIPTION, POWER....8N-18
SEAT TRACK - DIAGNOSIS AND
TESTING, POWER....................8N-18
SEAT TRACK - INSTALLATION...........23-83
SEAT TRACK - INSTALLATION, POWER . . . 8N-19
SEAT TRACK - OPERATION, POWER.....8N-18
SEAT TRACK - REMOVAL..............23-83
SEAT TRACK - REMOVAL, POWER.......8N-19
SEATBELT INDICATOR - DESCRIPTION....8J-34
SEATBELT INDICATOR - OPERATION......8J-34
SEATS - CLEANING, INTAKE/EXHAUST
VALVES ............................9-248
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES . 9-122,9-246,9-27,9-305,9-375
SEATS - DESCRIPTION, POWER.........8N-14
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES ............................9-248
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES...........9-123,9-248,9-29
SEATS - OPERATION, POWER............8N-14
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES ...................9-122,9-248,9-28
SECONDARY CATCH - INSTALLATION,
LATCH STRIKER.....................23-48
SECONDARY CATCH - REMOVAL, LATCH
STRIKER...........................23-48
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY INDICATOR - DESCRIPTION....8J-34
SECURITY INDICATOR - OPERATION.....8J-35
SECURITY SYSTEM, DIAGNOSIS AND
TESTING - VEHICLE THEFT..............8Q-3
SELECTION - STANDARD PROCEDURE,
HEAD GASKET.......................9-330
SELECTOR INDICATOR - DESCRIPTION,
GEAR..............................8J-26
SELECTOR INDICATOR - OPERATION,
GEAR..............................8J-27
SELECTOR SWITCH - DESCRIPTION....21-685,
21-719
SELECTOR SWITCH - OPERATION......21-685,
21-719
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL........14-68,14-7
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-8
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL.....................14-68,14-7
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-7
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-10
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-12
SENSE - PCM INPUT - OPERATION, ASD
. . . 8I-6
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD)
.................8W-01-8
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION
....................14-25
SENSOR - DESCRIPTION, AMBIENT
TEMP
.............................8M-10
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE
......................8F-21
SENSOR - DESCRIPTION, CAMSHAFT
POSITION
..........................14-82
SENSOR - DESCRIPTION, CAMSHAFT
POSITION
............................8I-8
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION
.....................14-26,14-83
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE
...............7-44
SENSOR - DESCRIPTION, FRONT WHEEL
SPEED
..............................5-41
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT
..................14-68,14-7
SENSOR - DESCRIPTION, FUEL
PRESSURE
.........................14-72
SENSOR - DESCRIPTION, HEATED SEAT
. . . 8G-7SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - DESCRIPTION, INPUT SPEED . 21-558
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-93
SENSOR - DESCRIPTION, KNOCK........8I-25
SENSOR - DESCRIPTION, LINE
PRESSURE (LP)....................21-559
SENSOR - DESCRIPTION, MAP.....14-39,14-94
SENSOR - DESCRIPTION, MODE . . 21-684,21-718
SENSOR - DESCRIPTION, OUTPUT
SPEED............................21-567
SENSOR - DESCRIPTION, OXYGEN.......14-43
SENSOR - DESCRIPTION, POSITION....21-618,
21-654
SENSOR - DESCRIPTION, SPEED . 21-254,21-431
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-52
SENSOR - DESCRIPTION,
TRANSMISSION RANGE . . 21-263,21-441,21-581
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE . 21-267,21-445,
21-583
SENSOR - DESCRIPTION, WATER IN
FUEL..............................14-77
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-11
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8G-7
SENSOR - DIAGNOSIS AND TESTING,
REAR WHEEL SPEED..................5-43
SENSOR - INSTALLATION,
ACCELERATOR PEDAL POSITION........14-25
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - INSTALLATION, CAMSHAFT
POSITION..........................14-83
SENSOR - INSTALLATION, CAMSHAFT
POSITION...........................8I-14
SENSOR - INSTALLATION, CRANKSHAFT
POSITION.....................14-30,14-84
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-47
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-42
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-8
SENSOR - INSTALLATION, FUEL
PRESSURE.........................14-72
SENSOR - INSTALLATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - INSTALLATION, INPUT SPEED . 21-559
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE......................14-38
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-94
SENSOR - INSTALLATION, KNOCK........8I-26
SENSOR - INSTALLATION, LINE
PRESSURE (LP)....................21-560
SENSOR - INSTALLATION, MAP.........14-42
SENSOR - INSTALLATION, OUTPUT
SPEED............................21-567
SENSOR - INSTALLATION, OXYGEN......14-45
SENSOR - INSTALLATION, POSITION....21-619,
21-654
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-43
SENSOR - INSTALLATION, THROTTLE
POSITION..........................14-54
SENSOR - INSTALLATION,
TRANSMISSION RANGE........21-266,21-444
SENSOR - OPERATION, ACCELERATOR
PEDAL POSITION....................14-25
SENSOR - OPERATION, AMBIENT TEMP . . 8M-10
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-21
SENSOR - OPERATION, CAMSHAFT
POSITION
..........................14-82
SENSOR - OPERATION, CAMSHAFT
POSITION
............................8I-8
SENSOR - OPERATION, CRANKSHAFT
POSITION
.....................14-26,14-83
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE
...............7-44
SENSOR - OPERATION, FRONT WHEEL
SPEED
..............................5-41
30 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT..................14-68,14-7
SENSOR - OPERATION, FUEL PRESSURE . . 14-72
SENSOR - OPERATION, HEATED SEAT.....8G-7
SENSOR - OPERATION, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - OPERATION, INPUT SPEED . . . 21-558
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-93
SENSOR - OPERATION, KNOCK..........8I-25
SENSOR - OPERATION, LINE PRESSURE
(LP)..............................21-559
SENSOR - OPERATION, MAP...........14-39
SENSOR - OPERATION, MODE . . . 21-684,21-718
SENSOR - OPERATION, OUTPUT SPEED . . 21-567
SENSOR - OPERATION, OXYGEN........14-43
SENSOR - OPERATION, POSITION......21-619,
21-654
SENSOR - OPERATION, SPEED . . . 21-254,21-431
SENSOR - OPERATION, THROTTLE
POSITION..........................14-52
SENSOR - OPERATION, TRANSMISSION
RANGE................21-263,21-441,21-581
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE.........21-267,21-445,21-583
SENSOR - OPERATION, WATER IN FUEL . . 14-78
SENSOR - REMOVAL, ACCELERATOR
PEDAL POSITION....................14-25
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-21
SENSOR - REMOVAL, CAMSHAFT
POSITION..........................14-83
SENSOR - REMOVAL, CAMSHAFT
POSITION...........................8I-11
SENSOR - REMOVAL, CRANKSHAFT
POSITION.....................14-29,14-84
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-44
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-41
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-7
SENSOR - REMOVAL, FUEL PRESSURE . . . 14-72
SENSOR - REMOVAL, HEATED SEAT......8G-7
SENSOR - REMOVAL, INLET AIR
TEMPERATURE SENSOR/PRESSURE......14-90
SENSOR - REMOVAL, INPUT SPEED.....21-559
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE SENSOR/MAP...........14-93
SENSOR - REMOVAL, KNOCK...........8I-25
SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-559
SENSOR - REMOVAL, MAP.............14-40
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-567
SENSOR - REMOVAL, OXYGEN..........14-44
SENSOR - REMOVAL, POSITION . . 21-619,21-654
SENSOR - REMOVAL, REAR WHEEL
SPEED
..............................5-42
SENSOR - REMOVAL, THROTTLE
POSITION
..........................14-53
SENSOR - REMOVAL, TRANSMISSION
RANGE
......................21-265,21-443
SENSOR - REMOVAL, WATER IN FUEL
....14-78
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE
......8M-11
SENSOR RETURN - DESCRIPTION
.......8E-10
SENSOR (TRS) - DIAGNOSIS AND
TESTING, TRANSMISSION RANGE
......21-264,
21-442
SENSOR/MAP SENSOR - DESCRIPTION,
INTAKE AIR TEMPERATURE
............14-93
SENSOR/MAP SENSOR - INSTALLATION,
INTAKE AIR TEMPERATURE
............14-94
SENSOR/MAP SENSOR - OPERATION,
INTAKE AIR TEMPERATURE
............14-93
SENSOR/MAP SENSOR - REMOVAL,
INTAKE AIR TEMPERATURE
............14-93
SENSOR/PRESSURE SENSOR -
DESCRIPTION, INLET AIR
TEMPERATURE
......................14-90
SENSOR/PRESSURE SENSOR -
INSTALLATION, INLET AIR
TEMPERATURE
......................14-90SENSOR/PRESSURE SENSOR -
OPERATION, INLET AIR TEMPERATURE . . . 14-90
SENSOR/PRESSURE SENSOR -
REMOVAL, INLET AIR TEMPERATURE....14-90
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-66
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE.....................9-343,9-67
SENSOR/SWITCH - OPERATION, OIL
PRESSURE..........................9-66
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE.....................9-343,9-67
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-13
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-13
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-15
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - DESCRIPTION........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INDICATOR LAMP - OPERATION..........8Q-5
SENTRY KEY IMMOBILIZER SYSTEM
INITIALIZATION, STANDARD
PROCEDURE.........................8Q-3
SENTRY KEY IMMOBILIZER SYSTEM
(SKIS), DESCRIPTION..................8Q-1
SENTRY KEY IMMOBILIZER SYSTEM
TRANSPONDER PROGRAMMING,
STANDARD PROCEDURE...............8Q-4
SEPARATOR - DESCRIPTION, FUEL
FILTER / WATER .....................14-61
SEPARATOR - INSTALLATION, FUEL
FILTER / WATER .....................14-62
SEPARATOR - OPERATION, FUEL FILTER
/ WATER ...........................14-61
SEPARATOR - REMOVAL, FUEL FILTER /
WATER.............................14-61
SERVO - ASSEMBLY, FRONT.....21-209,21-388
SERVO - ASSEMBLY, REAR......21-253,21-430
SERVO - CLEANING, FRONT.....21-208,21-388
SERVO - CLEANING, REAR......21-252,21-430
SERVO - DESCRIPTION.................8P-6
SERVO - DESCRIPTION, FRONT . . 21-207,21-387
SERVO - DESCRIPTION, REAR . . . 21-252,21-429
SERVO - DISASSEMBLY, FRONT . . 21-208,21-388
SERVO - DISASSEMBLY, REAR . . . 21-252,21-430
SERVO - INSPECTION, FRONT . . . 21-208,21-388
SERVO - INSTALLATION................8P-7
SERVO - OPERATION..................8P-7
SERVO - OPERATION, FRONT....21-208,21-387
SERVO - OPERATION, REAR.....21-252,21-429
SERVO - REMOVAL....................8P-7
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-12
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHAFT - ASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT...........21-245,21-423
SHAFT - CAUTION, HALF................3-11
SHAFT - DESCRIPTION, PLANETARY
GEARTRAIN/OUTPUT...........21-242,21-420
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-11
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - DISASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT...........21-243,21-421
SHAFT - INSPECTION, PLANETARY
GEARTRAIN/OUTPUT...........21-245,21-422
SHAFT - INSTALLATION, BALANCE........9-79
SHAFT - INSTALLATION, FRONT
PROPELLER...........................3-7
SHAFT - INSTALLATION, HALF...........3-12
SHAFT - INSTALLATION, IDLER.....9-175,9-80
SHAFT - INSTALLATION, REAR
PROPELLER...........................3-8
SHAFT - OPERATION, PLANETARY
GEARTRAIN/OUTPUT...........21-243,21-420
SHAFT - REMOVAL, BALANCE...........9-79
SHAFT - REMOVAL, FRONT PROPELLER
....3-6
SHAFT - REMOVAL, HALF
...............3-11
SHAFT - REMOVAL, IDLER
.........9-175,9-79
SHAFT - REMOVAL, REAR PROPELLER
.....3-7
SHAFT - SPECIAL TOOLS, HALF
..........3-12SHAFT - SPECIAL TOOLS, PROPELLER.....3-6
SHAFT - SPECIFICATIONS, HALF..........3-12
SHAFT - SPECIFICATIONS, PROPELLER.....3-6
SHAFT - STANDARD PROCEDURE,
PROPELLER...........................3-3
SHAFT FRONT BEARING -
INSTALLATION, OUTPUT........21-217,21-395
SHAFT FRONT BEARING - REMOVAL,
OUTPUT.....................21-217,21-395
SHAFT REAR BEARING - INSTALLATION,
OUTPUT.....................21-217,21-396
SHAFT REAR BEARING - REMOVAL,
OUTPUT.....................21-217,21-395
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT.........21-618,21-653,21-683,21-717
SHAFT SEAL - INSTALLATION, STEERING
GEAR INPUT........................19-28
SHAFT SEAL - REMOVAL, FRONT
OUTPUT.........21-617,21-653,21-683,21-717
SHAFT SEAL - REMOVAL, STEERING
GEAR INPUT........................19-25
SHAFT SEALS - INSTALLATION, AXLE . 3-33,3-58,
3-84
SHAFT SEALS - REMOVAL, AXLE . 3-33,3-58,3-84
SHAFTS - ASSEMBLY, AXLE.............3-58
SHAFTS - DISASSEMBLY, AXLE..........3-56
SHAFTS - INSTALLATION, AXLE....3-111,3-138,
3-33,3-58,3-83
SHAFTS - REMOVAL, AXLE . . . 3-111,3-138,3-33,
3-56,3-83
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH.................23-41
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH................23-41
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-40
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH................23-41
SHIELDS - DESCRIPTION, HEAT..........11-7
SHIELDS - INSTALLATION, HEAT.........11-8
SHIELDS - REMOVAL, HEAT.............11-7
SHIFT BOOT - INSTALLATION, 4WD
FLOOR.............................23-64
SHIFT BOOT - REMOVAL, 4WD FLOOR....23-63
SHIFT COVER - INSTALLATION....21-128,21-86
SHIFT COVER - REMOVAL.......21-128,21-86
SHIFT INTERLOCK - ADJUSTMENTS,
BRAKE TRANSMISSION . . 21-195,21-376,21-540
SHIFT INTERLOCK - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION......21-195,
21-375,21-540
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-194,
21-375,21-540
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-194,
21-375,21-540
SHIFT LEVER - ADJUSTMENT....21-622,21-657
SHIFT LEVER - INSTALLATION . . . 21-621,21-656
SHIFT LEVER - INSTALLATION, GEAR.....19-12
SHIFT LEVER - REMOVAL.......21-620,21-655
SHIFT LEVER - REMOVAL, GEAR........19-12
SHIFT MECHANISM - DESCRIPTION....21-253,
21-430,21-574
SHIFT MECHANISM - INSTALLATION.....21-85
SHIFT MECHANISM - OPERATION......21-253,
21-430,21-574
SHIFT MECHANISM - REMOVAL.........21-84
SHIFT MOTOR - DESCRIPTION . . . 21-686,21-720
SHIFT MOTOR - INSTALLATION . . 21-686,21-720
SHIFT MOTOR - OPERATION.....21-686,21-720
SHIFT MOTOR - REMOVAL......21-686,21-720
SHOCK - DIAGNOSIS AND TESTING . . . 2-23,2-35
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-38
SHOCK - INSTALLATION............2-35,2-40
SHOCK - REMOVAL................2-35,2-40
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-34
SHOES - INSTALLATION................5-34
SHOES - REMOVAL
....................5-33
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
..........................8W-01-10
SIDE - INSTALLATION, LEFT
............9-122
SIDE - INSTALLATION, RIGHT
...........9-121
DRINDEX 31
Description Group-Page Description Group-Page Description Group-Page

TACHOMETER - DESCRIPTION..........8J-37
TACHOMETER - OPERATION............8J-37
TAIL LAMP - INSTALLATION............8L-21
TAIL LAMP - REMOVAL................8L-21
TAIL LAMP UNIT - INSTALLATION.......8L-21
TAIL LAMP UNIT - REMOVAL...........8L-21
TAILGATE - INSTALLATION.............23-17
TAILGATE - REMOVAL.................23-17
TAILPIPE - 5.9L DIESEL - INSPECTION....11-9
TAILPIPE - 5.9L DIESEL - INSTALLATION . . . 11-9
TAILPIPE - 5.9L DIESEL - REMOVAL......11-9
TAILPIPE - INSPECTION...............11-10
TAILPIPE - INSTALLATION..............11-10
TAILPIPE - REMOVAL.................11-10
TANK - DESCRIPTION, FUEL............14-20
TANK - OPERATION, FUEL..............14-20
TANK MODULE - DESCRIPTION, FUEL....14-75
TANK MODULE - INSTALLATION, FUEL....14-75
TANK MODULE - OPERATION, FUEL......14-75
TANK MODULE - REMOVAL, FUEL.......14-75
TAPPETS - DIAGNOSIS AND TESTING,
HYDRAULIC....................9-258,9-386
TASK MANAGER - DESCRIPTION.........25-1
TASK MANAGER - OPERATION...........25-5
TCM QUICK LEARN - STANDARD
PROCEDURE........................8E-21
TEMP INDICATOR - DESCRIPTION,
TRANS.............................8J-38
TEMP INDICATOR - OPERATION, TRANS . . 8J-38
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-10
TEMP SENSOR - OPERATION, AMBIENT . . 8M-10
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-23
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-23
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-21
TEMPERATURE SENSOR - DESCRIPTION,
ENGINE COOLANT.....................7-44
TEMPERATURE SENSOR - DESCRIPTION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION.........21-267,21-445,21-583
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-11
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-21
TEMPERATURE SENSOR -
INSTALLATION, ENGINE COOLANT........7-47
TEMPERATURE SENSOR -
INSTALLATION, INTAKE AIR............14-38
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-21
TEMPERATURE SENSOR - OPERATION,
ENGINE COOLANT.....................7-44
TEMPERATURE SENSOR - OPERATION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION.........21-267,21-445,21-583
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-21
TEMPERATURE SENSOR - REMOVAL,
ENGINE COOLANT.....................7-44
TEMPERATURE SENSOR - REMOVAL,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-11
TEMPERATURE SENSOR/MAP SENSOR -
DESCRIPTION, INTAKE AIR.............14-93
TEMPERATURE SENSOR/MAP SENSOR -
INSTALLATION, INTAKE AIR............14-94
TEMPERATURE SENSOR/MAP SENSOR -
OPERATION, INTAKE AIR...............14-93
TEMPERATURE SENSOR/MAP SENSOR -
REMOVAL, INTAKE AIR................14-93
TEMPERATURE SENSOR/PRESSURE
SENSOR - DESCRIPTION, INLET AIR.....14-90
TEMPERATURE SENSOR/PRESSURE
SENSOR - INSTALLATION, INLET AIR
.....14-90
TEMPERATURE SENSOR/PRESSURE
SENSOR - OPERATION, INLET AIR
.......14-90
TEMPERATURE SENSOR/PRESSURE
SENSOR - REMOVAL, INLET AIR
........14-90
TEMPORARY - DESCRIPTION, SPARE
TIRE
................................22-5
TEMPORARY TIRE - DESCRIPTION,
SPARE
.............................22-15TENSION REDUCER - DESCRIPTION,
SEAT BELT .........................8O-48
TENSION REDUCER - DIAGNOSIS AND
TESTING, SEAT BELT.................8O-49
TENSION REDUCER - OPERATION, SEAT
BELT ..............................8O-49
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-47
TENSIONER - OPERATION, SEAT BELT....8O-48
TENSIONERS - 3.7L / 4.7L -
DESCRIPTION, BELT...................7-22
TENSIONERS - 3.7L / 4.7L -
INSTALLATION, BELT...................7-23
TENSIONERS - 3.7L / 4.7L - OPERATION,
BELT ...............................7-22
TENSIONERS - 3.7L / 4.7L - REMOVAL,
BELT ...............................7-22
TENSIONERS - 5.9L - DESCRIPTION,
BELT ...............................7-23
TENSIONERS - 5.9L - INSTALLATION,
BELT ...............................7-24
TENSIONERS - 5.9L - OPERATION, BELT . . . 7-23
TENSIONERS - 5.9L - REMOVAL, BELT.....7-23
TENSIONERS - 5.9L DIESEL -
DESCRIPTION, BELT...................7-24
TENSIONERS - 5.9L DIESEL -
INSTALLATION, BELT...................7-25
TENSIONERS - 5.9L DIESEL -
OPERATION, BELT.....................7-24
TENSIONERS - 5.9L DIESEL - REMOVAL,
BELT ...............................7-25
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL..............8W-01-14
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE . . 21-140,21-321,21-493
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - DIAGNOSIS AND TESTING,
VACUUM SUPPLY.....................8P-2
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-10
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-11
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-10
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-8
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION..........................25-1
TEST MODE - DESCRIPTION, STATE
DISPLAY............................25-1
TESTER - STANDARD PROCEDURE,
USING MICRO 420 BATTERY............8F-12
TESTS - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION/LEAKAGE.....9-288
THEFT SECURITY SYSTEM, DIAGNOSIS
AND TESTING - VEHICLE...............8Q-3
THERMOSTAT - 3.7L/4.7L -
DESCRIPTION, ENGINE COOLANT.........7-50
THERMOSTAT - 3.7L/4.7L -
INSTALLATION, ENGINE COOLANT........7-51
THERMOSTAT - 3.7L/4.7L - OPERATION,
ENGINE COOLANT.....................7-51
THERMOSTAT - 3.7L/4.7L - REMOVAL,
ENGINE COOLANT.....................7-51
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT.........7-52
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT........7-53
THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-52
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT............7-53
THERMOSTAT - DIAGNOSIS AND
TESTING....................7-48,7-51,7-52
THERMOSTAT-5.7L/5.9L - DESCRIPTION,
ENGINE COOLANT.....................7-47
THERMOSTAT-5.7L/5.9L -
INSTALLATION, ENGINE COOLANT........7-49
THERMOSTAT-5.7L/5.9L - OPERATION,
ENGINE COOLANT
.....................7-48
THERMOSTAT-5.7L/5.9L - REMOVAL,
ENGINE COOLANT
.....................7-48
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM
. 21-156,21-337,21-495
THREADED HOLE REPAIR -
DESCRIPTION
......................Intro.-9
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN
.....9-186,9-232,
9-289,9-361,9-9,9-93THROTTLE BODY - DESCRIPTION........14-45
THROTTLE BODY - INSTALLATION.......14-47
THROTTLE BODY - OPERATION.........14-45
THROTTLE BODY - REMOVAL...........14-45
THROTTLE CONTROL CABLE -
INSTALLATION..................14-51,14-96
THROTTLE CONTROL CABLE - REMOVAL . 14-49,
14-94
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-52
THROTTLE POSITION SENSOR -
INSTALLATION.......................14-54
THROTTLE POSITION SENSOR -
OPERATION.........................14-52
THROTTLE POSITION SENSOR -
REMOVAL..........................14-53
THROTTLE VALVE CABLE -
ADJUSTMENTS...............21-255,21-432
THROTTLE VALVE CABLE -
DESCRIPTION................21-254,21-432
TIE DOWN - INSTALLATION, CARGO BOX . 23-37
TIE DOWN - REMOVAL, CARGO BOX.....23-37
TIE ROD END - DIAGNOSIS AND
TESTING, OUTER.....................19-31
TIE ROD END - INSTALLATION..........19-37
TIE ROD END - INSTALLATION, OUTER . . . 19-32
TIE ROD END - REMOVAL..............19-36
TIE ROD END - REMOVAL, OUTER.......19-31
TIMING - DESCRIPTION, VALVE..........9-75
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-65
TIMING - OPERATION, VALVE............9-75
TIMING - VERIFICATION - STANDARD
PROCEDURE, ENGINE.................9-165
TIMING BELT / CHAIN COVER(S) -
INSTALLATION........9-169,9-278,9-404,9-81
TIMING BELT / CHAIN COVER(S) -
REMOVAL............9-168,9-278,9-404,9-80
TIMING BELT/CHAIN AND SPROCKETS -
INSPECTION....................9-171,9-83
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION........9-172,9-279,9-406,9-84
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL............9-169,9-279,9-405,9-81
TIMING CHAIN STRETCH - INSPECTION,
MEASURING...................9-279,9-405
TIMING CHAIN WEAR - STANDARD
PROCEDURE, MEASURING.............9-165
TIMING CHAIN WEAR, STANDARD
PROCEDURE - MEASURING.............9-76
TIMING CHAIN/TENSIONER -
DESCRIPTION.......................9-222
TIMING CHAIN/TENSIONER - OPERATION . 9-222
TIMING DRIVE SYSTEM - DESCRIPTION . . 9-164
TIMING DRIVE SYSTEM - OPERATION....9-164
TIMING, SPECIFICATIONS - IGNITION......8I-6
TIMING VERIFICATION - SERVICE
PROCEDURE.........................9-76
TIMING VERIFICATION - STANDARD
PROCEDURE........................9-348
TIMING/CHAIN AND SPROCKETS -
INSTALLATION.......................9-222
TIMING/CHAIN AND SPROCKETS -
REMOVAL..........................9-221
TIMING/CHAIN COVER - INSTALLATION
. . . 9-221
TIMING/CHAIN COVER - REMOVAL
.......9-220
TIP INSERTS - INSTALLATION, SPRING
....2-42
TIP INSERTS - REMOVAL, SPRING
........2-41
TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME RAIL
.........................13-4
TIRE - DESCRIPTION, FULL SIZE, SPARE
WHEEL WITH MATCHING
..............22-15
TIRE - DESCRIPTION, SPARE /
TEMPORARY
........................22-15
TIRE / TEMPORARY - DESCRIPTION,
SPARE
..............................22-5
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE
................22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING
........................22-1
TIRE INFLATION PRESSURES -
DESCRIPTION
........................22-6
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING
........................22-7
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION
........................22-6
34 INDEXDR
Description Group-Page Description Group-Page Description Group-Page