2003 DAEWOO MATIZ Drum wheel

2A–2 SUSPENSION DIAGNOSIS
DAEWOO M-150 BL2
Condition Probable Cause Correction
Car Lead/Pull
Mismatched or uneven tires.
Replace the tires.

A broken or a sagging coil spring.
Replace the coil spring.

A improperly radial tire lateral force.
Check the wheel alignment.

Switch the tire and wheel assemblies.

Replace the tires as needed.

The front–wheel alignment is
out–of–align.
Align the front wheels.

Off–center steering gear.
Reseat the pinion valve assembly.

Replace the pinion valve assembly as
needed.

Front–brake dragging.
Adjust the front brakes.
Abnormal or Excessive
Tire Wear
The front–wheel and rear–wheel
alignment is out–of–align.
Align the front and the rear wheels.

Excessive toe.
Adjust the toe.

A broken or a sagging coil spring.
Replace the coil spring.

Out–of–balance tires.
Balance the tires.

Worn strut dampeners.
Replace the strut dampeners.

A failure to rotate tires.
Rotate the tires.

Replace the tires as needed.

Overloaded vehicle.
Maintain the proper load weight.

Low tire inflation.
Inflate the tires to the proper pressure.
Scuffed Tires
Incorrect toe.
Adjust the toe.

A twisted or a bent suspension arm.
Replace the suspension arm.
Wheel Tramp
An out–of–balance tire or wheel.
Balance the tire or the wheel.

Improper strut dampener action.
Replace the strut dampeners.
Shimmy, Shake, or
An out–of–balance tire or wheel.
Balance the tire or the wheel.
Vibration
Excessive wheel hub runout.
Measure the hub flange runout.

Replace the hub as needed.

Excessive brake drum or brake rotor
imbalance.
Adjust the brakes.

Replace the brake rotor or the brake
drum as needed.

Worn tie rod ends.
Replace the tie rod ends.

Wheel trim imbalance.
Balance the wheel.

A worn ball joint.
Replace the control arm and ball joint
assembly.

Excessive wheel runout.
Measure the wheel runout.

Replace the wheel as needed.

Excessive loaded radial runout on the
tire and wheel assembly.
Match–mount the tire and wheel
assembly.

2D –12 REAR SUSPENSION
DAEWOO M-150 BL2
UNIT REPAIR
D106C701
HUB AND BEARING ASSEMBLY
Tools Required
DW 340–010 Front Wheel Hub Remover
DW 350–030 Rear Wheel Bearing Race Installer
Disassembly Procedure
1. Remove the rear brake drum. Refer to Section 4E,
Rear Drum Brakes.
2. Remove the rear wheel bearing.

Remove the outer tapered roller bearing (1).
D106C702

Remove the oil seal (2).

Remove the inner tapered roller bearing (3).
D106C703
3. Remove the bearing races from the brake drum.

Remove the inner bearing race (1).

REAR SUSPENSION 2D–13
DAEWOO M-150 BL2
D106C704

Remove the outer bearing race (2).
Important: Use only new bearing race.
D106C705
Assembly Procedure
1. Press the bearing race into the break drum using the
front wheel hub remover DW 340–010 and the rear
wheel bearing race installer DW 350–030.

Press the inner bearing race (1).
D106C706

Press the outer bearing race (2).
D106C707
2. Install the wheel bearing and oil seal into the brake
drum.
Important: Coat or fill all the hollow spaces of both
wheel bearing, the ring seal lip and the brake drum with
antifriction grease.

Install the inner bearing (1).

Install the oil seal (2).

REAR SUSPENSION 2D–15
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application Unit Description
Suspension Type– Isolated Trailing Link
Maximum Lengthmm (in.) 394.5 ± 3 (15.53 ± 0.12)
Shock Absorber Minimum Lengthmm (in.) 257.5 ± 3 (10.14 ± 0.12)

Shock Absorber
Strokemm (in.) 137 (5.39)
Clearancemm (in.) 0
Rear Wheel Bearing No LoadNm (lb-in.) 0.137 – 0.422 (0.9 – 3.7)
Coil Spring Height (No Load)mm (in.) 291 (11.46)
Grease Type (Rear Wheel Bearing and Hub)–M–8143 ANTIF BRG GREASE
FASTENER TIGHTENING SPECIFICATIONS
Application Nm Lb-Ft Lb-In Shock Absorber–to–Body Bracket Nut 45 – 70 33 – 52 – Shock Absorber–to–Rear Axle Bolt 45 – 70 33 – 52 – Trailing Arm–to–Rear Axle Bolt 80 – 90 59 – 66 – Trailing Arm–to–Body Bracket Bolt 70 – 90 55 – 66 – Lateral Rod–to–Body Bracket Bolt 50 – 70 37 – 52 – Lateral Rod–to–Rear Axle Nut 35 – 55 25 – 41 – Rear Axle Castellated Nut* – – – ABS Rear Speed Sensor Retaining Bolt 9 – 13 – 80 – 11 5

Rear Axle Castellated Nut : Refer to Section 4E, Rear Drum Brakes

TIRES AND WHEELS 2E–7
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON-VEHICLE SERVICE
D106A501
D106A502
WHEEL
Removal Procedure
1. Remove the wheel cover on the vehicle equipped
with steel wheel.
2. Loosen the wheel nuts.
3. Raise and suitably support the vehicle.
4. Remove the wheel nuts.
Notice: Never use heat to loosen a tight wheel. It can
shorten the life of the wheel, the wheel nuts and the
wheel bearings. Excessive force, such as hammering
the wheel or tire, can also cause damage and is not rec-
ommended. Slight tapping of the wheel sidewall with
one’s hand or with a rubber mallet is acceptable.
5. Remove the wheel.
Difficulty in removing the wheels from the vehicle can be
due to foreign material or to a tight fit between the wheel
centerhole and the hub or the rotor. These wheels can
be removed by
1. Retightening the wheel nuts on the affected wheel
and then loosening the wheel nuts by two turns.
2. Lowering the vehicle and rocking it from side to side
as hard as possible, using one or more person’s body
weight to loosen the wheel.
3. Raising the vehicle and removing the wheel.
Caution: Do not allow the penetrating oil to get on
the vertical surfaces between the wheel and the
drum (or rotor) because penetrating oil in this area
could cause the wheel to work loose as the vehicle
is driven, resulting in loss of control and an injury
accident.
Penetrating oil is not effective in removing tight wheels.
If it is used, however, apply it sparingly and only to the
wheel’s centerhole area.

2E –8 TIRES AND WHEELS
DAEWOO M-150 BL2
D16A503A
90–11 0 Nm
Installation Procedure
Notice: Before installing the wheels, remove any build-
up of corrosion on the wheel mounting surface and the
brake drum or the rotor mounting surface by scraping
and brushing them with a wire brush. Installing the
wheels without good metal-to-metal contact at the
mounting surfaces can cause the wheel nuts to loosen,
which can later allow a wheel to come off while the ve-
hicle is moving. Wheel nuts must be tightened in se-
quence and to the proper torque to avoid bending the
wheel, the brake drum or the rotor.
1. Mount the wheel.
2. Install the wheel nuts in the diagonally. Do not tighten
the wheel nuts.
3. Lower the vehicle.
Tighten
Tighten the wheel nuts to 90–110 Nm (66–81 lb-ft).
ON-VEHICLE BALANCING
On-vehicle balancing will help correct vibrations due to
brake drum, rotor, and wheel cover imbalances.
Notice: Do not allow the front suspension to hang free.
When the drive axle is run at an extreme angle, extra
vibrations can occur, as well as damage to seals and
joints.
1. During on-vehicle balancing, do not remove the bal-
ance weights from the off-vehicle dynamic balance.
2. If more than 1 ounce of additional weight is required,
split the weight between the inner and the outer rim
flanges.
3. Spin the driven tire and wheel assemblies using the
engine.
OFF-VEHICLE BALANCING
Perform wheel balancing with an electronic off-vehicle
balancer. The balancer is easy to use and gives both a
static and a dynamic balance. Unlike on-vehicle balanc-
ing, the off-vehicle balancer does not correct for drum or
rotor imbalance. This drawback is overcome by its accu-
racy. Secure the wheel on the balancer with a cone
through the back side of the centerhole, not through the
wheel nut holes.
CORRECTING NON-UNIFORM TIRES
There are two ways to correct properly balanced tires
which still vibrate. One method uses an automatic
machine which loads the tire and buffs small amounts of
rubber from high spots on the outer two tread rows.
Correction by this method is usually permanent and, if it
is done properly, does not significantly affect the
appearance or the tread life of the tire. Tire truing with a
blade-type machine is not recommended because it
substantially reduces the tread life and often does not
correct the problem permanently.

4A –4 HYDRAULIC BRAKES
DAEWOO M-150 BL2
DIAGNOSITIC INFORMATION AND PROCEDURES
BRAKE SYSTEM TESTING
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Brakes should be tested on a dry, clean, reasonably
smooth and level roadway. A true test of brake perfor-
mance cannot be made if the roadway is wet, greasy, or
covered with loose dirt whereby all tires do not grip the
road equally. Testing will also be adversely affected if the
roadway is crowned so as to throw the weight so roughly
that the wheels tend to bounce.
Test the brakes at different vehicle speeds with both light
and heavy pedal pressure; however, avoid locking the
brakes and sliding the tires. Locked brakes and sliding
tires do not indicate brake efficiency since heavily
braked, but turning, wheels will stop the vehicle in less
distance than locked brakes. More tire-to-road friction is
present with a heavily braked, turning tire than with a
sliding tire.
Because of the high deceleration capability, a firmer
pedal may be felt at higher deceleration levels.
There are three major external conditions that affect
brake performance:

Tires having unequal contact and grip of the road will
cause unequal braking. Tires must be equally in-
flated, and the tread pattern of the right and the left
tires must be approximately equal.

Unequal loading of the vehicle can affect the brake
performance since the most heavily loaded wheels
require more braking power, and thus more braking
effort, than the others.

Misalignment of the wheels, particularly conditions of
excessive camber and caster, will cause the brakes
to pull to one side.
To check for brake fluid leaks, hold constant foot pres-
sure on the pedal with the engine running at idle and the
shift lever in NEUTRAL. If the pedal gradually falls away
with the constant pressure, the hydraulic system may be
leaking. Perform a visual check to confirm any sus-
pected leaks.
Check the master cylinder fluid level. While a slight drop
in the reservoir level results from normal lining wear, an
abnormally low level indicates a leak in the system. The
hydraulic system may be leaking either internally or ex-
ternally. Refer to the procedure below to check the mas-
ter cylinder. Also, the system may appear to pass this
test while still having a slight leak. If the fluid level is nor-
mal, check the vacuum booster pushrod length. If an in-
correct pushrod length is found, adjust or replace the
rod.Check the master cylinder using the following proce-
dure:

Check for a cracked master cylinder casting or brake
fluid leaking around the master cylinder. Leaks are in-
dicated only if there is at least one drop of fluid. A
damp condition is not abnormal.

Check for a binding pedal linkage and for an incorrect
pushrod length. If both of these parts are in satisfac-
tory condition, disassemble the master cylinder and
check for an elongated or swollen primary cylinder or
piston seals. If swollen seals are found, substandard
or contaminated brake fluid should be suspected. If
contaminated brake fluid is found, all the components
should be disassembled and cleaned, and all the rub-
ber components should be replaced. All of the pipes
must also be flushed.
Improper brake fluid, or mineral oil or water in the fluid,
may cause the brake fluid to boil or cause deterioration
of the rubber components. If the primary piston cups in
the master cylinder are swollen, then the rubber parts
have deteriorated. This deterioration may also be evi-
denced by swollen wheel cylinder piston seals on the
drum brake wheels.
If rubber deterioration is evident, disassemble all the hy-
draulic parts and wash the parts with alcohol. Dry these
parts with compressed air before reassembly to keep al-
cohol out of the system. Replace all the rubber parts in
the system, including the hoses. Also, when working on
the brake mechanisms, check for fluid on the linings. If
excessive fluid is found, replace the linings.
If the master cylinder piston seals are in satisfactory
condition, check for leaks or excessive heat conditions.
If these conditions are not found, drain the fluid, flush the
master cylinder with brake fluid, refill the master cylin-
der, and bleed the system. Refer to “Manual Bleeding
the Brakes” in this section.
BRAKE HOSE INSPECTION
The hydraulic brake hoses should be inspected at least
twice a year. The brake hose assembly should be
checked for road hazard damage, cracks, chafing of the
outer cover, and for leaks or blisters. Inspect the hoses
for proper routing and mounting. A brake hose that rubs
on a suspension component will wear and eventually
fail. A light and a mirror may be needed for an adequate
inspection. If any of the above conditions are observed
on the brake hose, adjust or replace the hose as neces-
sary.

HYDRAULIC BRAKES 4A–13
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
0.8 SOHC Engine
Application Millimeters Inches



Brake Drums:
Inside Diameter
Maximum Rebore Diameter
Out-of-Round


180
182
0.04


7.09
7.17
0.0016




Brake Rotors:
Discard Thickness
Lateral Runout (Installed)
Rotor Diameter
Rotor Thickness (New)



10
0.05
236
12.7




0.4
0.002
9.3
0.5
Master Cylinder:
Bore Diameter 20.64 0.81
Caliper:
Piston Diameter
48

1.89
Wheel Cylinder Diameter: 17.46 0.69



Brake Pedal:
Free Play
Height
Stroke


6 – 10
200
30



0.24 – 0.31
7.87
1.18
Type DOT–3 or DOT–4 Brake Fluid Capacity 0.45 L (0.48 qt.)
FASTENER TIGHTENING SPECIFICATIONS

Application

Nm

Lb-Ft

Lb-In
Brake Pipe Fittings 16 12 –
Front Brake Hose-to-Caliper Bolt 25.5 19.1 –
Brake Pedal–to–Pedal Bracket Hex Bolt

18

13

–
Brake Pedal Bracket Mounting Bolts 18 – 26 13 – 20 –
Brake Pedal Bracket Mounting Nuts 18 – 26 13 – 20 –
Stoplamp Switch Mounting Bracket Bolts

9 – 12

–

80 – 106