2003 DAEWOO MATIZ Filter

1A–14 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
 Application Description
  Maximum Speed 144 km/h (90 mph)
 Vehicle Capacity Gradeability 0.420 tan θ
 
Vehicle Capacity
 Minimum Turning Radius 4.5 m (14.8 ft)
  Bore × Stroke 68.5 × 72.0 mm (2.70 × 2.83 inch)
  Displacement 796 cm3 (48.6 in3)
  Compression Ratio 9.3 : 1
  Maximum Power 37.5 KW (6,000 rpm)
 
Engine Information
 Maximum Torque 68.6 Nm (50.59 lb-ft) (at 4,600 rpm)
Ignition Timing (Ignition Sequence)5 BTDC (1–3–2) / 10 BTDC (1–3–2)   
Air Conditioning System (ON)
 
1,000 ± 50 rpm  Idle Speed Air Conditioning System (OFF) 950 rpm  Engine Overhead Cam L–3 
 
 
 Ignition Type
 
 Direct Ignition System (DIS) /
High Energy Ignition (HEI)
  Distributor Optical Sensor Type
  Starter SD 80
   Unleaded BPR5EY–11, RN9YC4, WR8DCX
  Spark–Plug Leaded BPR5EY, RN9YC, WR8DC
  Fuel Injection Type MPI
  Fuel Pump Electric Motor Pump
Engine Part TypeFuel FilterCartridge Engine Part Type 
Lubricating Type
 
Forced Feed Type  Oil Pump Rotary Pump Type  Cooling Type Forced Water Circulation  Radiator Cross – Flow  Water Pump Centrifugal  Thermostat Pellet Type
  Air Cleaner Element Non Woven Fablic
  Muffler Catalytic Converter, Closed Circuit
  Battery MF
Engine PartEngine OilSJ Grade
SAE 5W30, SAE 10W30, SAE 15W40
CapacityRefrigerantFour Seasons   
Engine Disassembly
 
3.0 L (3.17 qt)   Oil Change (Including filter) 2.7 L (2.85 qt)  Engine Oil Oil Change (Not including filter) 2.5 L (2.64 qt)   Oil Level Gauge 1 L (1.06 qt) (MIN to MAX)  Coolant 3.8 L (4.02 qt) Engine Information Battery 12V–35 AH, 246 CCA
 Engine Information  

Generator

65 A
  Starter 0.8 kW
   Output Capacity 90 – 133 Lph
  Fuel Pump Output Pressure 380 kPa (55.1 Psi)
  Fuel Tank Capacity 35 L (9.2 gal), 38 L (10 gal)

DAEWOO M-150 BL2
SECTION 1B
SOHC ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 1B-2. . . . . . . . . . . . . . . . . .
Engine Type 1B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication 1B-2. . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train 1B-2. . . . . . . . . . . . . .
Engine Block 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Rod 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Piston, Piston Ring and Piston Pin 1B-3. . . . . . . . . . .
Timing Belt and Pulley 1B-4. . . . . . . . . . . . . . . . . . . . .
Engine Mount 1B-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 1B-5. . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head 1B-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block 1B-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold & Air Flow System 1B-7. . . . . . . . . . . . . . . . .
Timing Belt & Engine Mount 1B-8. . . . . . . . . . . . . . . .
Diagnostic Information and Procedure 1B-9. . . . . . .
Compression Pressure Check 1B-9. . . . . . . . . . . . . . .
Oil Pressure Check 1B-9. . . . . . . . . . . . . . . . . . . . . . . .
Adjustment of Valve Clearance 1B-10. . . . . . . . . . . . .
Ignition Timing Check and Adjustment
(Typical) 1B-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Timing Check and Adjustment 1B-12. . . . . . . .
Repair Instructions 1B-14. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 1B-14. . . . . . . . . . . . . . . . . . . . . . . . . Air Filter Assembly 1B-14. . . . . . . . . . . . . . . . . . . . . . .
Air Filter Element 1B-15. . . . . . . . . . . . . . . . . . . . . . . . .
Positive Crankcase Ventilation (PCV) Hose
and Valve 1B-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1B-16. . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold (Typical) 1B-18. . . . . . . . . . . . . . . . .
Exhaust Manifold (Euro III) 1B-20. . . . . . . . . . . . . . . .
Timing Belt 1B-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan 1B-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor Case 1B-26. . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1B-28. . . . . . . . . . . . . . . . .
Engine Mount Damping Block 1B-32. . . . . . . . . . . . . .
Engine Mount Front Damping Bush 1B-34. . . . . . . . .
Engine Assembly 1B-35. . . . . . . . . . . . . . . . . . . . . . . . .
Unit Repair 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train
Components 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block Components 1B-59. . . . . . . . . . . . . . . . .
Specifications 1B-71. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications 1B-71. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 1B-73. . . . . . . . . .
Special Tools 1B-75. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1B-75. . . . . . . . . . . . . . . . . . . . . . .

1B – 2 SOHC ENGINE MECANICAL
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
ENGINE TYPE
The engine is 4-cycle, water-cooled, in-line 3 cylinders
with displacement of 796cc (68.5×72.0mm) (2.70×
2.83 in.).
Engine model
(Specifications)F8C Type SOHC /
2 Valve (MPI)
Maximum power (kw/rpm)37.5 / 6,000
Maximum torque (N
m/rpm)68.6 / 4,600
Compression ratio9.3 : 1
D102B001
ENGINE LUBRICATION
The engine lubrication is of the wetsump method to draw
up the oil forced by the oil pump. The oil pump is of a
trochoid type, and mounted on crankshaft at crankshaft
pulley side (a). Oil is drawn up through oil pump pickup
tube (b) and passed through pump (c) to oil filter (d). The
filtered oil flows into two paths in engine block. In one
path (e), oil reaches crankshaft journal bearings. Oil
from crankshaft journal bearings is supplied to connect-
ing rod bearings by means of intersecting passages
drilled in crankshaft, and then injected from a small hole
provided on big end of connecting rod to lubricate piston
(f), rings, and cylinder wall. In another path (g), oil goes
up to cylinder head and lubricates rocker arm (i), valve
(j), camshaft (k), etc. through the oil hole provided on the
rocker arm shaft (h).
D102B002
CYLINDER HEAD AND VALVE TRAIN
The cylinder head is made of cast aluminum alloy for
better strength in hardness with lightweight, and cam-
shaft (k) and rocker arm shaft (h) arranged in-line sup-
port.
D102B003
The combustion chambers are formed into the manifold
combustion chambers with increased squish parts for
better combustion efficiency and its intake and exhaust

1B –6 SOHC ENGINE MECANICAL
DAEWOO M-150 BL2
ENGINE BLOCK
D21B0011
1 Oil Level Gauge Stick
2Piston
3 Connecting Rod
4 Engine Block
5 Oil Filter6 Flywheel
7 Crankshaft
8 Oil Pan
9 Oil Pump Strainer
10 Oil Pump Assembly

SOHC ENGINE MECANICAL 1B–7
DAEWOO M-150 BL2
MANIFOLD & AIR FLOW SYSTEM
D21B0021
1 Intake Manifold
2 Exhaust Gas Recirculation (EGR) Pipe
3 Exhaust Gas Recirculation (EGR) Valve and
Solenoid
4 Throttle Body Assembly
5 Air Filter Assembly
6 Resonator7 Snorkel
8 Oxygen Sensor
9 Exhaust Manifold
10 Exhaust Manifold Heat Shield
11 Exhaust Manifold Heat Shield (Euro III)
12 Exhaust Manifold (Euro III)

1B –10 SOHC ENGINE MECANICAL
DAEWOO M-150 BL2
ADJUSTMENT OF VALVE
CLEARANCE
Adjust the valve clearance in the following procedures:
1. Remove the air filter/resonator assembly and the
relevant parts installed on the cylinder head cover.
2. Remove the cylinder head cover hexagon bolts and
remove the cover.
3. Turn over the crankshaft to make No.1 cylinder
matched with the compression top dead center.
(When the camshaft sprocket notch (d) is aligned with
the timing belt rear cover triangle pointer (e) and the
crankshaft sprocket point (f) is aligned with the oil
pump housing point (g), the compression top dead
center is on the ignition sequence for No. 1 cylinder.)
D102B303
4. Check the valve clearance for No. 1 cylinder com-
pression top dead center.

Condition

Cylinder
No.

1

2

3

Compression topIntake
dead center of
No.1 cylinder
Exhaust

marks indicates the place where the valve clear-
ance can be checked and adjusted.
5. If the checking for the valve clearance of No.1 cylin-
der compression top dead center is over, position
No.1 cylinder on the exhaust top dead center as rotat-
ing the crankshaft in a 360–degree arc. (When the
camshaft sprocket point (h) is aligned with the timing
belt rear cover triangle pointer (e), the exhaust top
dead center is on the ignition sequence for No. 1 cyl-
inder.)
D102B304
6. Check the valve clearance for the No. 1 cylinder ex-
haust top dead center.

Condition

Cylinder
No.

1

2

3

Exhaust top deadIntake
center of No.1
cylinder
Exhaust

marks indicates the place where the valve clear-
ance can be checked and adjusted.
Check and adjust the valve clearance (i) using thick-
ness gauge (j).
D102B305
D102B306

1D–12 ENGINE COOLING
DAEWOO M-150 BL2
D12D5091
4. Remove the electric cooling fan.
Refer to “Electric Cooling Fan” in this section.
5. Remove the radiator.
Remove the bolts (1).
Remove the radiator support brackets (2).
Remove the radiator (3).
6. Check the radiator for breaking, clog or other dam-
age.
Important: The radiator still contains a substantial
amount of coolant. Drain the remainder of the coolant
from the radiator into a drain pan.
D12D5101
Installation Procedure
1. Install the radiator with the mounting bolts (1) and the
support brackets (2).
Tighten
Tighten the support bracket bolts to 3.5–4.5 Nm
(31–40 lb-in).
2. Install the electric cooling fan.
Refer to “Electric Cooling Fan” in this section.
D12D5111
3. Connect the upper radiator hose to the radiator (1).
4. Connect the surge tank hose to the radiator (2).
5. Secure each hose with hose clamps.
6. Refill the engine cooling system. Refer to “Draining
and Refilling the Cooling System” in this section.
7. Connect the negative battery cable.
D102D512
THERMOSTAT (TYPICAL)
Removal Procedure
Caution: To prevent personal injury, do not remove
the surge tank cap while the engine and the radiator
are hot because the heat causes the system to re-
main under pressure. Scalding fluid and steam may
be blown out under pressure.
1. Remove air filter assembly. Refer to Section 1B,
SOHC Engine Mechanical.
2. Disconnect the lower radiator hose and drain the
coolant. Refer to “Drain and Refilling the Cooling Sys-
tem”
3. Disconnect the upper radiator hose.

ENGINE COOLING 1D–13
DAEWOO M-150 BL2
Loosen the hose clamp (1).
Disconnect the upper radiator hose (2).
D102D513
4. Remove the thermostat.
Remove the bolts (1).
Remove the thermostat housing (2).
Remove the thermostat with the gasket (3).
5. Check the gasket for crack or other damage.
6. Inspect the valve seat for foreign matter that could
prevent the valve from seating properly.
7. Inspect the thermostat for proper operation. Refer to
“Thermostat Test” in this section.
8–15 Nm
D12D514A
Installation Procedure
1. Install the thermostat with the bolts and the thermo-
stat housing.
Tighten
Tighten the mounting bolts to 8–15 Nm (71–130
lb-in).
2. Secure the upper radiator hose to the thermostat
housing with a hose clamp.
3. Refill the engine cooling system. Refer to “Draining
and Refilling the Cooling System” in this section.
MAA1D010
THERMOSTAT (EURO III)
Removal Procedure
Caution: To prevent personal injury, do not remove
the surge tank cap while the engine and the radiator
are hot because the heat causes the system to re-
main under pressure. Scalding fluid and steam may
be blown out under pressure.
1. Remove air filter assembly. Refer to Section 1B,
SOHC Engine Mechanical.
2. Disconnect the lower radiator hose and drain the
coolant. Refer to “Drain and Refilling the Cooling Sys-
tem”
3. Disconnect the upper radiator hose.