2002 JEEP LIBERTY interior

[x] Cancel search: interior

steering wheel jacking timing belt belt TPMS reset manual transmission

Load previous 8 pages

Page 1683 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual The blower motor is located on the passenger side
of the vehicle under the dash
(1) Disconnect and isolate the battery negative
cable.
(2) Unplug the blower motor wire harness connec-
tor (Fig. 2).
(3

Page 1686 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual (7) Disconnect the heater hoses from the heater
core tubes. Install plugs in, or tape over the opened
heater core tubes.
(8) Unplug the HVAC system vacuum supply line
connector from the engine side ha

(7) Disconnect the heater hoses from the heater
core tubes. Install plugs in, or tape over the opened
heater core tubes.
(8) Unplug the HVAC system vacuum supply line
connector from the engine side harness.
(9) Remove the nuts from the HVAC housing
mounting studs.
(10) Remove the HVAC housing from inside the
vehicle taking care not to allow any remaining cool-
ant to drain on the vehicles interior.
DISASSEMBLY
(1) Remove the HVAC housing from the vehicle
and place it on the workbench. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/DISTRIBUTION/HVAC
HOUSING - REMOVAL)
(2) Unplug the vacuum harness connectors from
the mode and recirculation door actuators and the
recirculation door actuator.
(3) Disengage the vacuum harness from any rout-
ing clips located on the lower half of the HVAC hous-
ing.
(4) Remove the blower motor and blower wheel
unit from the HVAC housing. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/DISTRIBUTION/
BLOWER MOTOR - REMOVAL)
(5) Pop out the grommet onl the vacuum supply
line and slide hole in housing.
(6) Carefully remove the foam seals from the
heater core and evaporator coil tube mounting flange
of the HVAC housing. If the either seal is deformed
or damaged it must be replaced.
(7) Use a screwdriver to pry off the four snap clips
that help secure the upper and lower HVAC housing
halves together.
(8) Remove the screws that secure the upper and
lower HVAC housing halves together.
(9) Carefully separate the upper HVAC housing
from the lower half.
ASSEMBLY
(1) Assemble the upper HVAC housing half to the
lower half. During assembly, be certain of the follow-
ing.
(a) That each of the mode door pivot shaft ends
and the two temperature blend door shafts are
properly engaged in there pivot holes.
(b) That the blower motor venturi ring is prop-
erly indexed and installed.
(c) If the unit is equipped with air conditioning,
that the evaporator coil tube rubber seal is prop-
erly positioned in the grooves in both the upper
and lower HVAC housing halves.
(2) Install the screws and four snap clips that
secure the upper and lower HVAC housing halves toeach other. Tighten the screws to 2.2 N´m (20 in.
lbs.).
(3) Install the blower motor and wheel unit in the
HVAC housing. (Refer to 24 - HEATING & AIR CON-
DITIONING/DISTRIBUTION/BLOWER MOTOR -
INSTALLATION)
(4) Install the foam seals on the flanges around
the heater core and evaporator coil tube mounting
flange of the HVAC housing.
(5) Insert the vacuum supply line and connector
through the foam seal on the heater core and evapo-
rator coil tube mounting flange of the HVAC housing.
Check that the vacuum grommet is securely seated
into the housing hole flange.
(6) Engage the vacuum harness to the routing
clips and plug in the vacuum harness connector at
the floor door actuator and, if the unit is so equipped,
at the recirculation air door actuator.
INSTALLATION
WARNING: IF THE VEHICLE IS EQUIPPED WITH AIR
CONDITIONING, REVIEW THE WARNINGS AND
CAUTIONS IN PLUMBING BEFORE PERFORMING
THE FOLLOWING OPERATION. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/PLUMBING - WARNING)
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - CAUTION) (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING - CAUTION -
REFRIGERANT HOSES/LINES/TUBES PRECAU-
TIONS)
(1) Position the HVAC housing to the dash panel.
Be certain that the evaporator condensate drain tube
and the housing mounting studs are inserted into
their correct mounting holes.
(2) Install and tighten the nuts onto the HVAC
housing mounting studs. Tighten the nuts to 6.2 N´m
(55 in.lbs.).
(3) Connect the HVAC system vacuum supply line
connector.
(4) Unplug or remove the tape from the heater
core tubes. Connect the heater hoses to the heater
core tubes and fill the engine cooling system(Refer to
7 - COOLING/ENGINE - STANDARD PROCE-
DURE).
(5) If the vehicle is not equipped with air condi-
tioning, go to Step 10.
(6) Unplug or remove the tape from the liquid line
and the evaporator inlet tube fittings. Connect the
liquid line coupler to the evaporator inlet tube. (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMB-
ING - STANDARD PROCEDURE - A/C LINE COU-
PLERS)
(7) Evacuate the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
24 - 34 DISTRIBUTIONKJ
HVAC HOUSING (Continued)

Page 1753 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-68
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION........................9-26
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..........

INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-68
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION........................9-26
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION....................9-28,9-36
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.......................9-27,9-35
INTERIOR - DESCRIPTION, LAMPS/
LIGHTING..........................8L-65
INTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING....................8L-68
INTERIOR - OPERATION, LAMPS/
LIGHTING..........................8L-67
INTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING....................8L-71
INTERLOCK CABLE - INSTALLATION,
PARK .............................21-153
INTERLOCK CABLE - REMOVAL, PARK . . . 21-153
INTERLOCK SYSTEM - DESCRIPTION,
BRAKE TRANSMISSION SHIFT.........21-124
INTERLOCK SYSTEM - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION
SHIFT.............................21-125
INTERLOCK SYSTEM - OPERATION,
BRAKE TRANSMISSION SHIFT.........21-125
INTERMEDIATE SHAFT - INSTALLATION . . . 19-11
INTERMEDIATE SHAFT - REMOVAL......19-11
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-4
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
INTRUSION TRANSCEIVER MODULE -
DESCRIPTION.......................8Q-14
INTRUSION TRANSCEIVER MODULE -
INSTALLATION......................8Q-16
INTRUSION TRANSCEIVER MODULE -
OPERATION.........................8Q-15
INTRUSION TRANSCEIVER MODULE -
REMOVAL..........................8Q-15
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
IOD FUSE - DESCRIPTION...........8W-97-3
IOD FUSE - INSTALLATION...........8W-97-3
IOD FUSE - OPERATION.............8W-97-3
IOD FUSE - REMOVAL..............8W-97-3
ISO FLARING - STANDARD PROCEDURE....5-8
JOINT - DESCRIPTION, UPPER
SUSPENSION ARM, BUSHINGS, AND
BALL...............................2-20
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - INSTALLATION, UPPER BALL.....2-20
JOINT - OPERATION, UPPER
SUSPENSION ARM, BUSHINGS, AND
BALL...............................2-20
JOINT - REMOVAL, UPPER BALL.........2-20
JOINT/BOOT-INNER - INSTALLATION, CV . . . 3-17
JOINT/BOOT-INNER - REMOVAL, CV.......3-15
JOINT/BOOT-OUTER - INSTALLATION, CV . . . 3-13
JOINT/BOOT-OUTER - REMOVAL, CV......3-12
JOINTS - ASSEMBLY, SINGLE CARDAN
UNIVERSAL...........................3-9
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL...................3-8
JOUNCE BUMPER - INSTALLATION.......2-19
JOUNCE BUMPER - REMOVAL...........2-19
JUMP STARTING PROCEDURE -
STANDARD PROCEDURE
.................0-5
JUNCTION BLOCK - DESCRIPTION
.....8W-97-4
JUNCTION BLOCK - DESCRIPTION
........5-20
JUNCTION BLOCK - DIAGNOSIS AND
TESTING
.........................8W-97-4
JUNCTION BLOCK - INSTALLATION
.......5-20
JUNCTION BLOCK - OPERATION
......8W-97-4
JUNCTION BLOCK - OPERATION
..........5-20
JUNCTION BLOCK - REMOVAL
...........5-20
KEY - DESCRIPTION, TRANSPONDER
....8Q-18
KEY - OPERATION, TRANSPONDER
......8Q-18
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY
................8E-15
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-18
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY
.................8E-16KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY............................8E-17
KEY TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE, SENTRY........8Q-8
KEY-IN IGNITION SWITCH -
DESCRIPTION.......................19-10
KEY-IN IGNITION SWITCH - DIAGNOSIS
AND TESTING.......................19-10
KEYLESS ENTRY MODULE -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY MODULE - DIAGNOSIS
AND TESTING, REMOTE................8N-7
KEYLESS ENTRY MODULE -
INSTALLATION, REMOTE...............8N-7
KEYLESS ENTRY MODULE - OPERATION,
REMOTE............................8N-7
KEYLESS ENTRY MODULE - REMOVAL,
REMOTE............................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-8
KEYLESS ENTRY TRANSMITTER -
SPECIFICATIONS, REMOTE..............8N-9
KNEE BLOCKER - INSTALLATION.......23-155
KNEE BLOCKER - REMOVAL...........23-155
KNOCK SENSOR - DESCRIPTION.........8I-11
KNOCK SENSOR - INSTALLATION........8I-12
KNOCK SENSOR - OPERATION..........8I-11
KNOCK SENSOR - REMOVAL............8I-12
KNUCKLE - INSTALLATION...............2-9
KNUCKLE - REMOVAL...................2-9
LABEL - DESCRIPTION, VEHICLE
EMISSION CONTROL INFORMATION
(VECI)............................Intro.-8
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION.....................Intro.-9
LACE - INSTALLATION, OPENING TRIM . . 23-180
LACE - REMOVAL, OPENING TRIM......23-180
LAMP BULB - INSTALLATION, ASH
RECEIVER..........................8L-71
LAMP BULB - INSTALLATION, CARGO....8L-73
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP BULB - INSTALLATION,
COURTESY.........................8L-76
LAMP BULB - INSTALLATION, FRONT....8L-27
LAMP BULB - INSTALLATION, FRONT
FOG ...............................8L-22
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-28
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-45
LAMP BULB - INSTALLATION, READING . . . 8L-79
LAMP BULB - INSTALLATION, REAR.....8L-59
LAMP BULB - INSTALLATION, REPEATER . . 8L-60
LAMP BULB - INSTALLATION, VANITY....8L-84
LAMP BULB - REMOVAL, ASH RECEIVER . . 8L-71
LAMP BULB - REMOVAL, CARGO........8L-72
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-18
LAMP BULB - REMOVAL, COURTESY.....8L-75
LAMP BULB - REMOVAL, FRONT........8L-26
LAMP BULB - REMOVAL, FRONT FOG....8L-21
LAMP BULB - REMOVAL, FRONT
POSITION..........................8L-28
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-44
LAMP BULB - REMOVAL, READING......8L-79
LAMP BULB - REMOVAL, REAR.........8L-58
LAMP BULB - REMOVAL, REPEATER.....8L-60
LAMP BULB - REMOVAL, VANITY........8L-83
LAMP INDICATOR - DESCRIPTION,
FRONT FOG.........................8J-19
LAMP INDICATOR - DESCRIPTION, REAR
FOG ...............................8J-27
LAMP INDICATOR - OPERATION, FRONT
FOG ...............................8J-19
LAMP INDICATOR - OPERATION, REAR
FOG ...............................8J-27
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-24
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR
.............8J-24
LAMP RELAY - DESCRIPTION, DAYTIME
RUNNING
...........................8L-20
LAMP RELAY - DESCRIPTION, FRONT
FOG
...............................8L-22
LAMP RELAY - DESCRIPTION, PARK
.....8L-54
LAMP RELAY - DESCRIPTION, REAR FOG
. 8L-56LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT FOG.................8L-23
LAMP RELAY - DIAGNOSIS AND
TESTING, PARK......................8L-55
LAMP RELAY - DIAGNOSIS AND
TESTING, REAR FOG..................8L-57
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - INSTALLATION, FRONT
FOG ...............................8L-24
LAMP RELAY - INSTALLATION, PARK.....8L-56
LAMP RELAY - INSTALLATION, REAR
FOG ...............................8L-58
LAMP RELAY - OPERATION, DAYTIME
RUNNING...........................8L-20
LAMP RELAY - OPERATION, FRONT FOG . . 8L-22
LAMP RELAY - OPERATION, PARK.......8L-54
LAMP RELAY - OPERATION, REAR FOG . . . 8L-57
LAMP RELAY - REMOVAL, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - REMOVAL, FRONT FOG . . . 8L-24
LAMP RELAY - REMOVAL, PARK........8L-55
LAMP RELAY - REMOVAL, REAR FOG....8L-58
LAMP REPLACEMENT - STANDARD
PROCEDURE, CMTC...................8M-2
LAMP REPLACEMENT - STANDARD
PROCEDURE, COURTESY...............8M-2
LAMP SWITCH - DESCRIPTION, BACKUP . . 8L-15
LAMP SWITCH - DESCRIPTION, BRAKE . . . 8L-16
LAMP SWITCH - DIAGNOSIS AND
TESTING, BACKUP.....................8L-15
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE.....................8L-17
LAMP SWITCH - INSTALLATION, BRAKE . . 8L-18
LAMP SWITCH - INSTALLATION, CARGO . . 8L-74
LAMP SWITCH - INSTALLATION,
READING...........................8L-80
LAMP SWITCH - OPERATION, BACKUP . . . 8L-15
LAMP SWITCH - OPERATION, BRAKE.....8L-16
LAMP SWITCH - REMOVAL, BRAKE......8L-17
LAMP SWITCH - REMOVAL, CARGO......8L-73
LAMP SWITCH - REMOVAL, READING....8L-80
LAMP UNIT - ADJUSTMENT, FRONT FOG . . 8L-25
LAMP UNIT - INSTALLATION, ASH
RECEIVER..........................8L-72
LAMP UNIT - INSTALLATION, CARGO.....8L-74
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP UNIT - INSTALLATION, COURTESY . . 8L-77
LAMP UNIT - INSTALLATION, FRONT.....8L-28
LAMP UNIT - INSTALLATION, FRONT
FOG ...............................8L-25
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-46
LAMP UNIT - INSTALLATION, READING . . . 8L-81
LAMP UNIT - INSTALLATION, REAR......8L-60
LAMP UNIT - INSTALLATION, REPEATER . . 8L-61
LAMP UNIT - REMOVAL, ASH RECEIVER . . 8L-72
LAMP UNIT - REMOVAL, CARGO........8L-74
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-19
LAMP UNIT - REMOVAL, COURTESY.....8L-76
LAMP UNIT - REMOVAL, FRONT.........8L-27
LAMP UNIT - REMOVAL, FRONT FOG.....8L-25
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-45
LAMP UNIT - REMOVAL, READING.......8L-81
LAMP UNIT - REMOVAL, REAR..........8L-59
LAMP UNIT - REMOVAL, REPEATER......8L-60
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
DIAGNOSIS AND TESTING..............8L-7
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-5
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS.....................8L-15
LAMPS/LIGHTING - INTERIOR -
DESCRIPTION.......................8L-65
LAMPS/LIGHTING - INTERIOR -
DIAGNOSIS AND TESTING.............8L-68
LAMPS/LIGHTING - INTERIOR -
OPERATION
.........................8L-67
LAMPS/LIGHTING - INTERIOR -
SPECIFICATIONS
.....................8L-71
LASH ADJUSTER - DIAGNOSIS AND
TESTING, HYDRAULIC
..............9-19,9-30
LATCH - ACCESS PANEL - DESCRIPTION
. 23-139
LATCH - ACCESS PANEL - INSTALLATION
. 23-139
14 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

Page 1764 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual SPARK PLUG - OPERATION.............8I-12
SPARK PLUG - REMOVAL..............8I-15
SPARK PLUG CABLE RESISTANCE, 2.4L....8I-3
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-13
SP

SPARK PLUG - OPERATION.............8I-12
SPARK PLUG - REMOVAL..............8I-15
SPARK PLUG CABLE RESISTANCE, 2.4L....8I-3
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-13
SPARK PLUGS, SPARK PLUG -
CLEANING..........................8I-15
SPARK PLUGS, SPECIFICATIONS..........8I-3
SPEAKER - DESCRIPTION..............8A-13
SPEAKER - INSTALLATION.............8A-15
SPEAKER - OPERATION...............8A-14
SPEAKER - REMOVAL.................8A-14
SPECIAL TOOLS - 3.7L ENGINE..........9-15
SPECIAL TOOLS - 8 1/4 AXLE...........3-98
SPECIAL TOOLS - BASE BRAKES..........5-7
SPECIAL TOOLS - BODY................23-5
SPECIAL TOOLS - COOLING.............7-14
SPECIAL TOOLS - FRONT AXLE..........3-34
SPECIAL TOOLS - FRONT SUSPENSION.....2-8
SPECIAL TOOLS - FUEL SYSTEM.........14-6
SPECIAL TOOLS - OUTER TIE ROD END
REMOVAL TOOL.....................19-15
SPECIAL TOOLS - POWER
DISTRIBUTION SYSTEMS............8W-97-2
SPECIAL TOOLS - POWER STEERING
PUMP.............................19-20
SPECIAL TOOLS - REAR AXLE...........3-63
SPECIAL TOOLS - RFE TRANSMISSION....21-120
SPECIAL TOOLS - STEERING COLUMN....19-8
SPECIAL TOOLS - WIRING/TERMINAL . 8W-01-10
SPECIAL TOOLS, BATTERY SYSTEM.......8F-7
SPECIFICATIONS, BATTERY SYSTEM......8F-6
SPECIFICATIONS, BRAKES - ABS.........5-33
SPECIFICATIONS, CHARGE CAPACITY.....24-42
SPECIFICATIONS, CLUTCH...............6-5
SPECIFICATIONS, DIAGNOSIS AND
TESTING............................22-8
SPECIFICATIONS, FLUID CAPACITIES.......0-4
SPECIFICATIONS, FRAME DIMENSIONS....13-3
SPECIFICATIONS, FRONT AXLE...........3-33
SPECIFICATIONS, GAP AND FLUSH.....23-116
SPECIFICATIONS, IGNITION TIMING.......8I-2
SPECIFICATIONS, LAMPS/LIGHTING -
EXTERIOR..........................8L-15
SPECIFICATIONS, LAMPS/LIGHTING -
INTERIOR..........................8L-71
SPECIFICATIONS, NV1500..............21-30
SPECIFICATIONS, OPENING DIMENSIONS . 23-111
SPECIFICATIONS, PAINT CODES........23-162
SPECIFICATIONS, REAR AXLE............3-62
SPECIFICATIONS, REMOTE KEYLESS
ENTRY TRANSMITTER.................8N-9
SPECIFICATIONS, SEALER LOCATIONS....23-87
SPECIFICATIONS, SPECIFICATIONS.......24-10
SPECIFICATIONS, STANDARD
PROCEDURE.........................23-4
SPECIFICATIONS, TORQUE..............13-6
SPECIFICATIONS, WELD AND
STRUCTURAL ADHESIVE LOCATIONS......23-9
SPEED CONTROL - DESCRIPTION........8P-1
SPEED CONTROL - OPERATION..........8P-1
SPEED CONTROL - TORQUE.............8P-2
SPEED SENSOR - DESCRIPTION, INPUT . 21-143
SPEED SENSOR - DESCRIPTION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, FRONT
WHEEL.............................5-34
SPEED SENSOR - INSTALLATION, INPUT . 21-143
SPEED SENSOR - INSTALLATION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, REAR
WHEEL.............................5-35
SPEED SENSOR - OPERATION, INPUT . . . 21-143
SPEED SENSOR - OPERATION, OUTPUT . . 21-152
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-34
SPEED SENSOR - REMOVAL, INPUT.....21-143
SPEED SENSOR - REMOVAL, OUTPUT . . . 21-152
SPEED SENSOR - REMOVAL, REAR
WHEEL.............................5-35
SPEEDOMETER - DESCRIPTION
.........8J-32
SPEEDOMETER - OPERATION
...........8J-32
SPLASH SHIELD - INSTALLATION,
FRONT WHEELHOUSE
................23-143
SPLASH SHIELD - INSTALLATION, REAR
WHEELHOUSE
......................23-144
SPLASH SHIELD - REMOVAL, FRONT
WHEELHOUSE
......................23-143SPLASH SHIELD - REMOVAL, REAR
WHEELHOUSE......................23-144
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-7
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-14
SPRING - INSTALLATION...........2-13,2-18
SPRING - REMOVAL...............2-13,2-18
SPRINGS - DESCRIPTION, VALVE.....9-29,9-38
SPRINGS - INSTALLATION, VALVE....9-29,9-38
SPRINGS - REMOVAL, VALVE........9-29,9-38
STABILIZER BAR - INSTALLATION....2-14,2-19
STABILIZER BAR - REMOVAL........2-14,2-19
STABILIZER BAR BUSHINGS -
INSTALLATION.........................2-9
STABILIZER BAR BUSHINGS - REMOVAL....2-9
STABILIZER LINK - INSTALLATION........2-14
STABILIZER LINK - REMOVAL............2-14
STAKING - STANDARD PROCEDURE,
HEAT ...............................23-3
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-39
STARTER MOTOR - INSTALLATION.......8F-41
STARTER MOTOR - REMOVAL..........8F-39
STARTER MOTOR, GAS POWERED.......8F-39
STARTER MOTOR RELAY - DESCRIPTION . 8F-41
STARTER MOTOR RELAY -
INSTALLATION.......................8F-43
STARTER MOTOR RELAY - OPERATION.....8F-42
STARTER MOTOR RELAY - REMOVAL.....8F-43
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-42
STARTING PROCEDURE - STANDARD
PROCEDURE, JUMP....................0-5
STARTING SYSTEM - DESCRIPTION......8F-32
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-33
STARTING SYSTEM - INSPECTION.......8F-37
STARTING SYSTEM - OPERATION........8F-32
STATE DISPLAY TEST MODE -
DESCRIPTION........................25-2
STEERING - DESCRIPTION..............19-1
STEERING - OPERATION................19-1
STEERING COLUMN, SPECIAL TOOLS.....19-8
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER.......19-3
STEERING LINKAGE - STANDARD
PROCEDURE........................19-16
STEERING PRESSURE SWITCH -
DESCRIPTION, POWER................19-22
STEERING PRESSURE SWITCH -
INSTALLATION, POWER...............19-22
STEERING PRESSURE SWITCH -
OPERATION, POWER..................19-22
STEERING PRESSURE SWITCH -
REMOVAL, POWER...................19-22
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-18
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-20
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-1
STEERING SYSTEM - DIAGNOSIS AND
TESTING, SUSPENSION.................2-1
STEERING WHEEL - INSTALLATION......19-12
STEERING WHEEL - REMOVAL..........19-12
STOP LAMP BULB - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP BULB - REMOVAL, CENTER
HIGH MOUNTED.....................8L-18
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-19
STRAP - DESCRIPTION, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRAP - INSTALLATION, CHECK . 23-121,23-128,
23-135
STRAP - INSTALLATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-11
STRAP - OPERATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRAP - REMOVAL, CHECK
.....23-121,23-128,
23-135
STRAP - REMOVAL, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRIKER - INSTALLATION, GLOVE BOX
LATCH
............................23-149STRIKER - INSTALLATION, HOOD AJAR
SWITCH............................8Q-14
STRIKER - INSTALLATION, LATCH......23-124,
23-132,23-137
STRIKER - INSTALLATION, REAR SEAT
BACK LATCH.......................23-171
STRIKER - REMOVAL, GLOVE BOX
LATCH ............................23-148
STRIKER - REMOVAL, HOOD AJAR
SWITCH............................8Q-13
STRIKER - REMOVAL, LATCH . . . 23-124,23-132,
23-137
STRIKER - REMOVAL, REAR SEAT BACK
LATCH ............................23-170
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS, WELD................23-9
STRUCTURAL COVER - DESCRIPTION.....9-55
STRUCTURAL COVER - INSTALLATION.....9-55
STRUCTURAL COVER - OPERATION.......9-55
STRUCTURAL COVER - REMOVAL........9-55
STUDS - INSTALLATION...............22-11
STUDS - REMOVAL...................22-11
SUCTION LINE - INSTALLATION, A/C.....24-49
SUCTION LINE - REMOVAL, A/C.........24-48
SUN VISOR - INSTALLATION..........23-160
SUN VISOR - REMOVAL..............23-160
SUN VISOR SUPPORT - INSTALLATION . . 23-160
SUN VISOR SUPPORT - REMOVAL......23-160
SUNROOF - DESCRIPTION............23-175
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-178
SUNSHADE - INSTALLATION...........23-179
SUNSHADE - REMOVAL..............23-179
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A.........8O-6
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING..............8O-6
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLIES - DESCRIPTION, 5 VOLT......8E-13
SUPPLIES - OPERATION, 5 VOLT........8E-15
SUPPORT - INSTALLATION, REAR
FASCIA..............................13-3
SUPPORT - INSTALLATION, SUN VISOR . . 23-160
SUPPORT - REMOVAL, REAR FASCIA......13-3
SUPPORT - REMOVAL, SUN VISOR.....23-160
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR.................23-161
SUPPORT CYLINDER - INSTALLATION . . . 23-120
SUPPORT CYLINDER - INSTALLATION,
FLIP-UP GLASS.....................23-139
SUPPORT CYLINDER - REMOVAL.......23-120
SUPPORT CYLINDER - REMOVAL,
FLIP-UP GLASS.....................23-139
SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO NOISE............8A-9
SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO NOISE...........8A-11
SUPPRESSION GROUND STRAP -
OPERATION, RADIO NOISE.............8A-10
SUPPRESSION GROUND STRAP -
REMOVAL, RADIO NOISE..............8A-10
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET............9-9
SUSPENSION - DIAGNOSIS AND
TESTING, REAR.......................2-17
SUSPENSION AND STEERING SYSTEM -
DIAGNOSIS AND TESTING...............2-1
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - DESCRIPTION, UPPER......2-20
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - OPERATION, UPPER........2-20
SUSPENSION, SPECIAL TOOLS - FRONT....2-8
SWING GATE - INSTALLATION.........23-138
SWING GATE - REMOVAL.............23-138
SWING GATE BELTLINE WEATHERSTRIP
- INSTALLATION....................23-186
SWING GATE BELTLINE WEATHERSTRIP
- REMOVAL
........................23-186
SWING GATE OPENING WEATHERSTRIP
- INSTALLATION
....................23-186
SWING GATE OPENING WEATHERSTRIP
- REMOVAL
........................23-186
SWITCH - DESCRIPTION
................8P-5
SWITCH - DESCRIPTION, A/C HIGH
PRESSURE
.........................24-17
KJINDEX 25
Description Group-Page Description Group-Page Description Group-Page

Page 1786 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual JEEP LIBERTY 2002
FRONT SEAT Contd25.000.00#.4 799.00 I 5 Adjuster;. Seat Belt R/L 55315033AC#.4 799.00 6 Buckle, :oeat Belt11 R/L 5GM341L5AB .2lIAdditional Parls &/or Deater Contact Required#w/Fron

JEEP LIBERTY 2002
FRONT SEAT Cont'd25.000.00#.4 799.00 I 5 Adjuster;. Seat Belt R/L 55315033AC#.4 799.00 6 Buckle, :oeat Belt11 R/L 5GM341L5AB '.2lIAdditional Parls &/or Deater Contact Required#w/Front Seat ASBY RemovedLIMITED MODEL Cont'd18 Switch, HeatPassenger Side 5GW44DX9ABDriver Side 5GW44DX9AB19 Switch, PowerPassen.Qer Side 55352782AADriver Side 55352782AA20 WIring, Seet1lPassenger Side 5O71990AADriver Side 5071991AA11Additional Parts &/or Dealer Contact Required21 Module, Heat ControlPassenger Side 56010113AADriver Side 56010113AA
25.4525.45
27.5027.50
40.9539.60
REAR
1
~2~
t'ower -
Passenger Side WD24WL8AADriver Side WD25XDVAA#WISest Assy Removed7 Handle, AdjusterPassenjjer Side 5072003AADriver Side 5072003AA8 Cable, ReclinerPassenjjer Side 5066458AADriver Side 5066458AA9 Shield, Adjuster1jManualPassenger Side R UZ50WL5AA .1L UZ42TL2AA .1Driver Side R UZ51WL5AA .1L UZ43TL2AA .1PowerPassenger SideHeateiJ R UZ541L2AAL UZ42TL2AANon-Heated R UZ52TL2AAL UZ43TL2AADriver SideHeated R UZ43TL2AAL UZ551L2AANon-Heated R UZ43TL2AAL UZ53WL5AA10 Recliner, Seal11Passenger Side R 5072020AAL 5072021AADriver Side R 5072022AAL 5072023AA1]Additional Paris &lor Dealer Contact Required11 Handle, ReclinerLight TaupePassenger SideTo 6-1-01 UZ281L2AAFrom 6-1-01 UZ281L2ABDriver SideTo 6-1-01 UZ291L2AAFrom 6-1-01 UZ291L2ABSlate GrayPassenger SideTo 6-1-01 UZ281DVAAFrom 6-1-01 UZ281 DVABDriver SideTo 6-1-01 UZ291 DVAAFrom 6-1-01 UZ291 DVABTaupePassenger SideTo 6-1-01 UZ281L5AAFrom 6'1-01 UZ281L5ABDriver SideTo 6-1-01 UZ291L5AAFrom 6-1-01 UZ291L5AB12 Knob, SwitchPassenjjer Side 4607042Driver Side 460704313 Switch, HeatPassenger Side 5GW44DX9ABDriver Side 5GW44DX9AB14 Switch, PowerPassenjjer Side 55352782AADriver Side 55352782AA15 Wiring, Seal11! Passenger Side 5071990AAIDriver Side 5071991AA1]Additional Paris &lor Dealer Contact Required16 Module, Heat Control! PassenSJer Side 56010113AADriver Side 56010113AA
16.3516.35
15.3515.35
19.3513.3519.3513.35~62.5062.50
RENEGADE, SPORT MODEL.1.1.1.1.1.1.1.1
3
~004-09550 ~20.50 1 Belt, Outer Rear Seat1] R 5HG341DVAD #1.0 112.0013.35 L 5HG331DVAB #1.0 209.0021.70 #Includes R&R Quarter Trim Panel13.35 2 Belt, Center Rear Seat1] 5HK441D2AA 119.003 Buckle, Rear Seat1] R 5GU581DVAD .2 30.9513.35 L 5GE491L5AD .2 45.6020.50 ~Additional Parts &/or Dealer Contact Required
83.60 I Use Procedure Explanations 16 and 28 with the following text.83.6083.60SHEET METAL
Refinish Door Outside. ...Add for Jambs & InteriorAddforJambs R&I Door Assy .""""'"
AIL 2.3AIL 1.0AIL .5AIL .612.7012.70
12.7012.70
1
""-l
12.7012.70
12.7012.70
#.8 28700#.8 287.00I#.8 287.00I#.8 287.0012.12:
12:12:
4.'4.'
25.25.
27.27.
40;39.'
~~004-09551
1 Cover, Seat BackSlate GrayPassenJjer Side UZ061DVAADriver Side UZ061DVAATaupePassenger Side UZ061L5AADriver Side UZ061L5AA2 Frame, Seat BackSlate GrayPassenger Side UZ321DVAA #.8 624.00Driver Side UZ331DVAA #.8 624.00TaupePassenJjer Side UZ321L5AA #.B 624.00Driver Side UZ331 L5AA #.B 624.00#R&R One Side Complete, wlSeat Assy Removed3 Cover, Seat CushionllSlate GrayPassenJjer Side UZ141DVAA 274.00Driver Side UZ141DVAA 274.00TaupePassenJjer Side UZ141L5AA 274.00Driver Side UZ141L5AA 274.004 Freme, Seat CushionManualPassenJjer Side 5O72110AA 144.00Driver Side 5O72111AA 144.00PowerPassenger Side 5O72110AA 144.00Driver S'tde 5O72126AA
~
1 Shell Assy, Door R 55176890AB #4.5 409.00L 55176891AB #4.5 410.00"ncludes R&UR&R Resr VIew Mirror2 Panel, Door Repair11 R 5066542AA #7.0 83.35L 5066543AA #7.0 0.001]lncluded wlDoor Shell Assy"ncludes R&UR&R Resr View MI"or & Door Glsss
EXTERIOR TRIM
R/L .4AiL #.6Refinish Side Moulding R&IRearViewMirror #Includes R&I Trim Panel
62.50!62.50
5-f1R&I Seal~Y:-: ;.,...~:::.:.:::::;;:.4
FRONT
1~~~~~~~~~~-, ~2
~~4~004-09552 --31 Moulding, Side (Adhesive)Limited ModelCode K2B I
Code K2E 1
Code K2F I
Code K2M
Code K2Q
Code K2R
Code K2S
Code K2T
Code K2W
Code K2X
\-52-t\)~
8/
i ~ TI\V6I
004-0954943
1 Belt, Front Seat1JTo 12-17-01 R 5HG341DVAD #.7 112.00L 5HG331DVAB #.7 209.00From 12-17-01 R 5HG341DVAC #.7 112.00L 5HG331DVAF #.7 260,00llAdditional Palts &lor Dealer Contact Required#Includes R&R Up~r & Lower Center Trim Panels2 Nut, Seat Belt R/L 6506002AA ,3 Plug, Lower TrimLight Taupe AiL 5HM79TL2AASlate Gray R/L 5HM79WL5AATaupe AiL 5HM79XDVAA
F 5GF54WB7ABL 5GF55WB7ABR 5GF54XGRABL 5GF55XGRABR 5GF54WE5ABL 5GF55WE5ABR 5GF54XRVABL 5GF55XRVABR 5GF54XBQABL 5GF55XBQABR 5GF54PR4ABL 5GF55PR4ABR 5GF54WS2ABL 5GF55WS2ABR 5GF54YU2ABL 5GF55YU2ABR 5GF54SW1ABL 5GF55SW1ABR 5GF54DX8ABL 5GF55DX8AB
.2 51.35.2 51.35.2 51.35.2 51.35.2 51.35.2 51.35.2 51.35.2 51.35.2 51.35.2 51.35.2 50.00.2 50.00.2 5f35.2 51.35.2 51.35.2 51.35.2 50.00.2 50.00..2 50.00.2 50.00
70
1.101.10
I1.10
Labor Times Shown are for Replacement with New OEM Undamaged Parts on New Undamaged Vehicles.Comments or suggestions? Need assistance? Call 1-800-854-7030 or 8~;8/578-6550, Ext 8220. Fax 1-888-256-7969 or 858/549-0629.572CH
7070
707060
604545
50501
95601

Page 1787 of 1803

$JEEP LIBERTY 2002 KJ / 1.G Workshop Manual \:-- .-11 ~ JEEP LIBERTY 2002enega e, po 5 :~5, Lock 507 3 2.35L 5GF35HS5AA .,. 29.~5 L 5072355AA 2.35eNamapiate (Adha$lve) 7 Hinge, Upper R/L 55177026AA #.2 28.35 2 "LIBERTY" R/L 55156604AA .2 23.7$

\:-- .-1'1
~
JEEP LIBERTY 2002enega e, po 5 :~5, Lock 507 3 2.35L 5GF35HS5AA .,. 29.'~5 L 5072355AA 2.35eNamapiate (Adha$lve) 7 Hinge, Upper R/L 55177026AA #.2 28.35 2 "LIBERTY" R/L 55156604AA .2 23.75 8 Hinge, Lower R/L 55177026AA #.2 28.35 I
3 "LIMITED EDITION" R/L 55156274AB .2 16.45 #W/Door Removed4 "SPORT" R/L 55156273AB .2 18.10 9 Check, Door R/L 55177028AB #.2 28.00Namep!ate /Adhesive) #w/Trim Panel Removed"RENEGADE" R/L N.A. .2 0.00 10 Seal, Lower Door R/L 55235928AA .2 11.255 Mirror, Rear View1j 11 Weatherstrip, Door11 R/L 5GU 15WL5AB .6 63.20Manual R 55155836AA #.3 75.50 ~Addilional Parts &/or Dealer Contact Required~-- L 55155837AA #.3 70.70-Power R 55155840AA #.3 106.00 GLASS & PARTSL 55155841AA #.3 101.00~11Additional Parts &/or Dealer Contact Required 2#W/Trim Panel ,Removed
004-09936INTERIOR TRIM
R&I Trim Panel " ,. """ AIL .3
NOTE: All Par!$ in this section are included in R&R TrimPanel unless noted otherwise.
Code K2E R 5GF38XGRAB .2 33.20L 5GF39XGRAB .2 33.20Code K2F R 5GF38WE5AB .2 33.20L 5GF39WE5AB .2 33.20Code K2M R 5GF38XRVAB .2 33.20L 5GF39XRVAB .2 33.20Code K20 R 5GF38XBOAB .2 33.20L 5GF39XBOAB .2 33.20Code K2R R 5GF38PR4AB .2 33.20L 5GF39PR4AB .2 33.20Code K2S R 5GF38WS2AB .2 33.20L 5GF39WS2AB .2 33.20Code K2T R 5GF38YU2AB .2 33.20L 5GF39YU2AB .2 33.20Code K2W R 5GF38SW1AB .2 33.20L 5GF39SW1AB .2 33.20Code K2X R 5GF38DX8AB .2 33.20L 5GF39DX8AB .2 33.20Renegade, Sport Model R 5GF30HS5AB .2 21.60L 5GF31HS5AB .2 21.602 Flare! Door Openinglimited ModelCode K5B R 5GF32WB7AA #.3 127.00L 5GF33WB7AA #.3 127.00.Code K5E R 5GF32XGRAA #.3 127.00L 5GF33XGRAA #.3 127.00Code K5F R 5GF32WE5AA #.3 127.00L 5GF33WE5AA #.3 127.00Code K5M R 5GF32XRVAA #.3 127.00L 5GF33XRVAA #.3 127.00Code K50 R 5GF32XBOAA #.3 127.00L 5GF33XBQAA #.3 127.00Code K5R R 5GF32PR4AA #.3 127.00L 5GF33PR4AA #.3 127.00Code KSS R 5GF32WS2AA #.3 127.00L 5GF33WS2AA #.3 127.00Code KST R 5GF32YU2AA #.3 127.00L 5GF33YU2AA #.3 127.00Code K5W R 5GF32SW1AA #.3 127.00L 5GF33SW1AA #.3 127.00Code K5X R 5GF32DX8AA #.3 127.00L 5GF33DX8AA #.3 127.00Renegade ModelCode K4C R 5HV50AFMAA #.3 91.70L 5HV49AFMAA #.3 91.70Code K4S R 5HVSOWS2AA #.3 91.70L 5HV49WS2AA #.3 91.70Code K4T R 5HV50YU2AA #.3 91.70L 5HV49YU2AA #.3 91.70Sport Model R 5GF36HS5AB #.3 63.00L 5GF37HS5AB #.3 63.00#Included in R&R Rear Door Shell Assy or Rear DoorRepair Panel
~--::f::::' 5-i
iIl3-~~42
~~:~
004-09927
~ 0--2
~3
004-09928 4
1 Panel, TrimllClothManual Windows R UX64WL5AA .4 290.00L UX65WL5AA .4 290.00Power Windows R UXOOWL5AA .4 200.00L UX61WL5AA .4 260.00Leather R UX681D2AA .4 285.00L UX691D2AA .4 287.002 Plug, Doo~ AiL 5GY30XDVAA 451\Addilional Parts &/or Dealer Contact Required3 Speaker, DoorStandard AiL 50038610AC #.2 43.00Premium AiL 50038593AC #.2 167004 Shield, Moisture R 55235892AB #.1 0.00L 55235893AB #.1 0.00#WlTrim Panel Removed, Not Included in R~rR TrimPanel
HARDWARE
AiL .3AiL .3AiL #.5
5 4,f
INTERIOR TRIM
/jR&ITrimPanel R/L .3
NOTE: All Parts in this section are included in R&R TrimPanel unless noted otherwise.
Refinish Upper Hinge Refinish Lower Hinge R&IOulsideHandleAssy "nclude, R&I Trim Panel
6
3~2.I .
7-d'
9-ri...,..@ 1 c 1 V
8~
.11/"
0 1"70-- 2
~
1 Shell Assy, Door R 55176906AAL 55176907AA2 Panel, Door Repai~ R 5066544AAL 5066545AA1]lncluded w/Door Shell Assy#Includes R&VR&R Door Glass
4.04.0#6.5#6.5
0.000.0010.000.00--004-09554
31 latCh, DoorManual Locks
Power Locks
Nwffr/m Panel2 Striker, Door3 Spacer, StrikerHandle, InsideIwffrlm Panel4 Rod, Inside Handle
5 Rod, Lock Knob
6 Handle, Outside
#Wffrlm Panel
#.3#.3#.3#.3
.2
#.2
004-09929
Illustration Located in Next Column
R 5GF38WB7ABL 5GF39WB7AB.2 33.20.2 33.20
Procedure Explanation Pages Must Be Used with the At,ove Text for an Accurate Damage Report.Comltlenlls or suggestuons? NeEd assistance? Call1-800.854-:r030 or 858/578-6550, Ext 8220. Fro( 1-888-256-7969 or 858/549-0629.573CH
1 Glass, Front DoorChrysler-Tinted R 55360374AB 1.0 0.00L 55360375AB 1.0 180.00INAGS-Green R/L ODO9984.5GTY 1.0 403.652 Weatherstrip, Outer Belt R 55235870AA .2 20.25L 55235871AA .2 20.2513 Weatherstrip, Inner Belt R 55235878AB 18.95L 55235879AB 18.954 Regulator, Windowtl;anual Windows R 55360032AB #.3 73.70IL 55360033AB #.3 73.70#W/Door Glass RemovedPower Windows~ R 55360030AB #.3 49.60IL 55360031AB #.3 49.601!Additional Parts &/or Dealer Contact RequiredMotor, Window R/L N.A. #.3 0.00#R&R One Side Complete, w/Door Glass RemovedHandle, Window R/[ FW80>:OV 6.505 Channel, Glass R 55235874AB #.9 78.50 IL 55235875AB #.9 78.50#W/Door Glass Removed Ceduct.6
R 55177040ACL 55177041ACR 55177042ACL 55177043ACRemoved
AiL 4780607AAAiL 4520289AiL N.A.Removed
R 5072350AAL 5072351AAR 55360534ABL 55360535ABR 55360332ABL 55360333ABRemoved
1 Panel, TrlmllCloth R 5GF18WL5AB .4 245.00L 5GF19WL5AB .4 245.00Leather R 5GF221D2AB .4 272.00L 5GF231D2AB .4 272.002 Plug, Door1] AiL 5GY30XDVAA .45llAdditional Parls &/or Dealer Contact Required3 Speaker. Door
Refinish Door Outside AiL 2.2AddforJambs&lnterior AiL 1.0AddforJambs AiL .5R&IDoorAssy AiL .6

Page 1790 of 1803

JEEP LIBERTY 2002 KJ / 1.G Workshop Manual JEEP LIBERTY 2002
QUARTER GLASS Confd410
OjJ.::::::::~~~~::::::::::;;;)t;
0.000.000.000.00
,...,.,,-
Privacyw/Antenna A 55360056AB #1.5L 55235923AB #1.5w/o Antenna A 55235922AB #1.5L 55235923AB #1.

JEEP LIBERTY 2002
QUARTER GLASS Conf'd410
OjJ.::::::::~~~~::::::::::;;;')t';
0.000.000.000.00
,...,.,,-
Privacyw/Antenna A 55360056AB #1.5L 55235923AB #1.5w/o Antenna A 55235922AB #1.5L 55235923AB #1.5NAGSTintedw/Antenna A DQO9990GTN #1.5 0.00L DQO9989GTN #1.5 302.751w/o Antenna AIL DO09988-9GTN #1.5 302.75Privacyw/Antenna A DO10069YPN #1.5 270.85L DQ10068YPN #1.5 297.95w/o Antenna AIL DO10067-8YPN #1.5 297.95#Includes Clean Up Old Adhesive as Necessary2 Spacer, Glass (4) 55360509M .35
32~
3~4~004-09943
55156554M55156275AB55156405M55156277M
Decal, Aear Gate1 "Jeep""3.7L""CAD"4 "Up Country"Use Procedure Explanations 25 and 28 with the fol/owing text.
R&IGlassAssy 3~
R&I Trim Panel ~~~~
~ '
.2~2 3
1\11 ..1-1[1\1
4~ '--004-09573-J2~
j~
.2 22.85 2 004-09575.2 13.101.2 25.45 1 Drum, Brake Ail 52128270AA m '.3 85.00.2 11.00 #R&R Both Sides.52 Shoe Set, Brake 5O66147AA m 11.4 108.00#Includes R&R Brake Drums3 Plate, Backing R 5066150AA m #.3 30.45l 506615tAA m #.3 30.45#W/Axle Shaft Assy Removed4 Shaft Assy, Axle R 5066484AA m.7 294.00l 5O66485AA m.7 295.005 Studl Wheell1 (5/Side) Ail 5016496AA m 1.2516 Retainer, Axle~ Ail 5O66486AA m'1.1 9.007 Seal, Axle~ Ail 5O12824AA m'1.1 3.458 Bearing, Axle1[ Ail 5012825AA m #1.1 56.509 Retainer, Beann9~ Ail 5O72894AA m #1.1 12.25~Included w/Axle Shaft Assy#R&R One Side Com~lefeSensor, Rear ABS-See ABS7Brakes Section10 Housing Assy, AxIe1] 5O66495AB m #5,0 1485.00~Additional Parts &/or Dealer Contact RequiredHousing, Axle (a) 5O66477AA m 17.7 817.00(a) Included w/Axle Housing Assy#Includes R&R Axle Shafts Assemblies
1 GlassChrYslerTinted 55360340AB.6 458.00Pnvacy 55360342AB650000NAGS ..
Tinted DBO9991GTY.6 1042.75 004-09572Pnvacy DBO9991YPY.6 1177301.Solar DB10070YPY.6 1177:30 1 Panel,RearGaIeTrlm~2 Hinge, Glass R 55360216AB #.4 23.95 wlStorage NetL 55360217AB #.4 23.95 Slate Gray#R&R Both Sides .5, Included in R&R Glass Taupe3 Stay, Glass AiL 55360171AA 2 3135 wlo Storage Net4 Striker, Glass 55360220AA #:2 21:50 Slate Gray#Included in R&R Glass Taupe
SHE6S)(DVACSHE6S\'lL5AC
SGE69;(DVACSGE69"lL5AC
.2 220.00.2 220.00
.2 125.00.2 125.00
#.1 20.4555360309M#WlTrim Panel Removed17111
WIPER SYSTI:MUse Procedure Explanations 25 and 28 with the fol/owing text.
SHEET METAUHARDWAREr10
1--17.l1
19-f1 ~21
~ E:-22 24
23~ ~~~
~~:==~~Y~::C:;==::~~O9576
11 Arm Assy, Upper Control 52088901AB m .8 212.0012 Joint, Ball~ 52088647M m #.3 50.0013 Bushing, Control Arm~ AiL 52086425 m #.2 11.95#W/Upper Control Arm Assy Removed.1 16.60 14 Bracket, Ball Join~ 52088894M m 56.25#.2 20.45 15 Bolt, Bracke~ 6503610 2.2016 Nu1, Bo~ 6503711 1'.451.60 ~/ncluded wlUpper Control Ann Assy4.95 17 Bolt, No.1 Mounting AiL 6504748 3.851.60 18 Bolt, No.2 Mounting (3) 6505445M 2.455.50 19 Absorber, Shock AiL 52088673AB m #.4 0.005.60 #R&R Both Sides .6, wlCoil Spring Removed Deduct .37.75 20 Isolator, Upper Spring AiL 52088707AA m 7.85#.3 125.00 1 Bumper, Ul?per AiL 52088705AB m 16.602 Spring, ColI'l AiL 52088695AB m #.6 54.95#.2 7.95 1jAdditlonal Palts &/or Dealer Contact Required#R&R Both Sides 1.0AiL 52128524M m 17.95AiL 52088682AB m #.6 102.00#WIAxle Housing Removed Deduct .325 Bar, Stabilizer 52088677AB m .5 127.00
~~~ "I fJ-s
9
~
Refinish Rear Gate Panel Outside 2.0Add for Jambs & Interior 1.0RefinishUpperGateHinge .2Refinish Lower Gate Hinge .2R&I Rear Gale Assy #1.4#Includes R&VR&R Left Qualter Trim PanelR&I Outside Handle #.4#Includes R&I Trim PanelR&ISpareTireBracket .2
7 56 I 8
l.s~-10 m'-
I004-09574 ---
1 Blade, Wiper 5066964AA2 Arm, Wiper 5066965AA#Includes R&R Wiper Blade3 Cover, Wiper Arm 550766504 Nut, Wiper Arm 65001655 Cover, Motor 550766506 Nut, Motor 65022637 Bezel, Motor 55155B87AA8 Stop, Wiper 5515~~86AA9 Motor, Wiper 55155e:84AA#w!rrim Panel Removed10 Nozzle, Washer 55156158AA#Included in R&R Roof Panel
4WD
4
-~~_~~~7~"'- --~3~ 1 ~~ 004-09570
1 Panel, Rear Gate 55176934AC #4.0 375.00#Includes R&VR&R Left Qualter Trim Panel2 Hinge, GateUpper 52850558AA #.2Lower 52850559AA #.2#WlRear Gate Assy RemovedCheck, Gate 55360170AA #.2 38.8513 Latch, Glass 55360357 AA #.2 70.85 Use Procedure Explanation 23 with the following text.Latch, Gate 55360359AA #.2 55.754 Handle, Outside 55360331AC #.35 Weatherstrip, Upper Gate 55360065AA #.2 -14.10 I#Wnrim Panel Removed6 Sta.bilizer, Gate 55360324AC 6.20 l R&I Suspension/Axle Assy .m 3.07Stnker 55176954AA.2 12.60~ Check Rear Alignment .m .88 Spacer, Striker 5507548.3 1.50, Add to Adjustrront Alignment9Bracket,SpareWheel-SeeWheelSecllon 2WD m .710 Weatherstrip, Rear 55716958AA .2 0.00 4WD m 1.0Bleed Brake Systemwi ABS m .6w/oABS m .3
NOTE: R&I/R&R Does Not include illignment or bleed brakesystem
Illustration Located in Next Column
1 Drum, Brake AIL 52128270AA m #.3 85.00#R&R Both Sides .52 Shoe Set, Brake 5066147AA m #1.4 108.00#Includes R&R Brake Drums3 Plate, Backing R 5066150AA m #.3 30.45L 5066151AA m #.3 30.45#W/Axle Shaft Assy Removed
labor Times Shown are for Replacement with New OEM Undamaged Parts on New Undamaged Vehicles.Comments or suggestions? Need assistance? Call1-80D-854-7030 or 8!i8/578-6550, Ex1 8220. Fax 1-888-256-7969 or 858/549-0629.576CH

Page: < prev 1-10 ... 73-80 81-88 89-96 97-104 105-112

change wheel center console bonnet tires steering wheel adjustment spark plugs replace