2001 TOYOTA SEQUOIA brake light

I28460
Wire Harness View:
E4
STP ST1±
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1555
1749 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check harness and connector (Stop light switch ± battery).
CHECK:
Measure the voltage according to the value(s) in the table below.
OK:
Tester connectionConditionSpecified condition
S14±4 ± Body groundAlways10 to 14 V
S14±2 ± Body groundIgnition SW ON10 to 14 V
NG Repair or replace harness or connector.
OK
5 Check voltage between terminals STP and ST1± of ECM connector and body
ground.
PREPARATION:
(a) Reconnect the stop light switch connector.
(b) Disconnect the ECM connector.
(c) Turn the ignition switch to the ON position.
CHECK:
Measure the voltage according to the value(s) in the table be-
low.
OK:
Tester connection
(Symbol)ConditionSpecified condition
E4±15 (STP) ±
Body groundBrake pedal depressed10 to 14 V
E4±15 (STP) ±
Body groundBrake pedal releasedBelow 1 V
E4±16 (ST1±) ±
Body groundBrake pedal depressedBelow 1 V
E4±16 (ST1±) ±
Body groundBrake pedal released10 to 14 V
NG Repair or replace harness or connector.
OK
Replace ECM (See page IN±35
).

I28425
Brake Master Cylinder

Brake Fluid Level Warning Switch
Engine Room R/B

ECU±B Fuse
Light Control RheostatCombination Meter Assembly
Instrument Panel J/B

IGN 2 Fuse

GAUGE Fuse
Parking Brake SwitchIgnition Switch
Passenger Seat
Belt Warning
Skid Control ECU
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1603
1797 Author: Date:
2005 SEQUOIA (RM1146U)

DID8P±01
I28566
Seat Position
Control ECU
A/C ECU (Integration
Control Panel) BEANBody ECU
Back Door ECU
ECM
Light Control
Rheostat
Vehicle Speed
Sensor
Oil Pressure
Sender Gauge
Fuel Sender Gauge
Seat Inner
Belt Switch
Park/neutral
Position Switch
Turn Signal
Flasher Relay
Washer Level SensorKey Unlock
Warning Switch
Door Courtesy
Lamp Switch
Parking Brake Switch
Transponder
Key ECU
4WD Control ECU
Airbag Sensor
Center ECU Combination
Meter
Skid Control ECU
Suspension
Control ECU
Translate ECU
Overhead Module
(Garage Door
Opener)BEAN
BEAN
BEAN
BEAN
BEAN BEAN
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1605
1799 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DID8U±01
DI±1614
± DIAGNOSTICSCOMBINATION METER SYSTEM
1808 Author: Date:
2005 SEQUOIA (RM1146U)
PROBLEM SYMPTOMS TABLE
HINT:
Inspect the related ºFuseº and ºRelayº before confirming the suspected area as shown in the table below.
MALFUNCTION SYSTEM:
SymptomSuspected AreaSee page
Entire combination meter does not operate.Refer to troubleshooting proceduresDI±1628
Operating light control rheostat does not change light brightness.Refer to troubleshooting proceduresDI±1645
Seat belt warning does not operate.Refer to troubleshooting proceduresDI±1650
Key reminder warning buzzer does not sound.
1. Multiplex communication system
2. Key unlock warning switch circuit
3. Door courtesy lamp switch circuit
4. Combination meter assyDI±1892
DI±1715
DI±1728
IN±35
METER GAUGES:
SymptomSuspected AreaSee page
Malfunction in speedometerRefer to troubleshooting proceduresDI±1632
Malfunction in tachometerRefer to troubleshooting proceduresDI±1636
Malfunction in fuel receiver gaugeRefer to troubleshooting proceduresDI±1640
Malfunction in engine coolant temperature receiver gaugeRefer to troubleshooting proceduresDI±1644
Malfunction in oil pressure receiver gaugeRefer to troubleshooting proceduresDI±1654
Malfunction in volt meterRefer to troubleshooting proceduresDI±1658
WARNING LIGHTS:
SymptomSuspected AreaSee page
Check engine warning light (MIL) does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Discharge warning light does not come on.
1. ECM
2. Wire harness or connector
3. Combination meter assyDI±9
±
IN±35
Brake warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
ABS warning light does not come on.
1. Skid control ECU
2. Wire harness or connector
3. Combination meter assyDI±895
±
IN±35
SRS warning light does not come on.
1. Airbag sensor assy
2. Wire harness or connector
3. Combination meter assyDI±1126
±
IN±35
Open door warning light does not come on.
1. Door courtesy light switch circuit
2. Wire harness or connector
3. Combination meter assy
4. Body ECUDI±1728
±
IN±35
IN±35
Fuel level warning light does not come on.
1. Refer to troubleshooting
2. Wire harness or connector
3. Combination meter assyDI±1640
±
IN±35
Low oil pressure warning light does not come on.
1. Low oil pressure warning switch
2. Wire harness or connector
3. Combination meter assyBE±55
±
IN±35

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1617
1811 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Reconnect the C5 and C6 connectors.
(d) Measure the voltage of each terminal of the wire harness side connector.
Standard:
Terminals No.Wiring ColorTerminal DescriptionConditionSpecified Condition
C5±1 ± Body groundR±B ± Body
groundParking brake signalParking brake warning light ON6.7 to 12 V
C5±1 ± Body groundR±B ± Body
groundParking brake signalParking brake warning light OFFBelow 1 V
C5±2 ± Body groundLG±R ± Body
groundCRUISE signalCRUISE indicator light ONBelow 1 V
C5±2 ± Body groundLG±R ± Body
groundCRUISE signalCRUISE indicator light OFF10 to 14 V
C5±3 ± Body groundB ± Body groundIgnition switch signal
(Start)Ignition switch OFFBelow 1 V
C5±3 ± Body groundB ± Body groundIgnition switch signal
(Start)Ignition switch START10 to 14 V
C5±4 ± Body groundG±Y ± Body
groundSeat belt condition signal
(Driver side)D±BELT indicator light ONBelow 1 V
C5±4 ± Body groundG±Y ± Body
groundSeat belt condition signal
(Driver side)D±BELT indicator light OFF10 to 14 V
C5±13 ± Body groundLG±R ± Body
groundWasher level signalWASH LVL indicator light ONBelow 1 V
C5±13 ± Body groundLG±R ± Body
groundWasher level signalWASH LVL indicator light OFF10 to 14 V
C5±14 ± Body groundL±O ± Body
groundO/D OFF indicator signalO/D OFF indicator light ONBelow 1 V
C5±14 ± Body groundL±O ± Body
groundO/D OFF indicator signalO/D OFF indicator light OFF10 to 14 V
C5±15 (*1) ± Body groundY±R ± Body
groundA/T oil temperature signalA/T OIL TEMP. warning light ONBelow 1 V
C5±15 (*1) ± Body groundY±R ± Body
groundA/T oil temperature signalA/T OIL TEMP. warning light OFF10 to 14 V
C5±16 ± Body groundLG±B ± Body
groundSecurity indicator light
signal (Engine immobilizer
system)
Security indicator light ON10 to 14 V
C5±16 ± Body groundLG±B ± Body
groundSecurity indicator light
signal (Engine immobilizer
system)
Security indicator light OFFBelow 1 V
C5±17 ± Body groundGR ± Body
groundSecurity indicator light
signal (Theft deterrent
system)
Security indicator light ON10 to 14 V
C5±17 ± Body groundGR ± Body
groundSecurity indicator light
signal (Theft deterrent
system)
Security indicator light OFFBelow 1 V
C5±18 ± Body groundV±W ± Body
groundCHECK ENGINE signalCHECK ENGINE warning light ONBelow 1 V
C5±18 ± Body groundV±W ± Body
groundCHECK ENGINE signalCHECK ENGINE warning light OFF10 to 14 V
C5±19 ± Body groundG±B ± Body
groundA/T shift position signal
(L)A/T L indicator OFFBelow 1 V

± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1687
1881 Author: Date:
2005 SEQUOIA (RM1146U)
WIRELESS DOOR LOCK CONTROL
SymptomSuspected AreaSee page
All functions of wireless door lock control system do not operate.
1. Transmitter
2. Wireless door lock receiver circuit
3. Key unlock warning switch circuit
4. Body ECUBE±99
DI±1737
DI±1715
IN±35
Lock (or unlock) function does not operate.
1. Door unlock detection switch circuit (Driver's)
(Passenger's)
(Rear Door)
(Back Door)
2. Any door ECU
3. Body ECUDI±1791
DI±1829
DI±1723
DI±1869
IN±35
IN±35
Automatic lock function operates even if any door is opened within
30 seconds after all doors are unlocked by wireless door lock
control system.1. Door courtesy light switch circuit
2. Any door ECU
3. Body ECUDI±1728
IN±35
IN±35
Wireless door lock function operates, but the buzzer does not
sound.1. Wireless door lock buzzer circuit
2. Body ECUDI±1741
IN±35
Buzzer sounds, but wireless door lock function does not operate.Body ECUIN±35
REAR WIPER AND WASHER
SymptomSuspected AreaSee page
Rear wiper does not operate.1. Rear wiper switch and motor circuit
2. Body ECUDI±1704
IN±35
Rear washer does not operate.1. Rear washer switch and motor circuit
2. Body ECUDI±1704
IN±35
LIGHT CONTROL
SymptomSuspected AreaSee page
Automatic light control does not operate.
1. Automatic light control sensor circuit
2. Light control switch circuit
3. Body ECUDI±1753
DI±1750
IN±35
Auto turn±off does not operate.
1. Door courtesy light switch circuit (Driver side)
2. Ignition switch
3. Driver door ECU
4. Body ECUDI±1728
BE±24
IN±35
IN±35
Daytime running light function does not operate.
1. Daytime running light relay circuit
2. Parking brake switch circuit
3. Body ECUDI±1712
DI±1744
IN±35
FOG LIGHT
SymptomSuspected AreaSee page
Fog lights do not come on.
1. Bulb
2. FOG fuse
3. Fog light relay and switch circuit
4. Body ECU±
BE±14
DI±1710
IN±35
OTHERS
SymptomSuspected AreaSee page
Illuminated entry function does not operate.1. Illumination circuit
2. Body ECUDI±1759
IN±35
All functions of the body control system do not operate.1. Power source circuit
2. Body ECUDI±1700
IN±35
Remote control mirror does not operate.
(w/ Driving position memory)1. Remote control mirror switch circuit
2. Driving position memory switch circuit
3. Body ECUDI±1767
DI±1772
IN±35

± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1691
1885 Author: Date:
2005 SEQUOIA (RM1146U) TAIL ± GND1
(B6±7 ± B6±6)
G ± W±BLight control switch
(TAIL)Light control switch OFF10 to 14 V
CLTS (*3) ± GND1
(B6±12 ± B6±6)Y ± W±BAutomatic light control
sensor (Signal)Ignition switch OFFBelow 1 V
CLTS (*3) ± GND1
(B6±12 ± B6±6)Y ± W±BAutomatic light control
sensor (Signal)Ignition switch ONSignal waveform
CLTE (*3) ± GND1
(B6±3 ± B6±6)BR ± W±BAutomatic light control
sensor (Ground)AlwaysBelow 1 V
CLTB (*3) ± GND1
(B6±4 ± B6±6)R±G ± W±BAutomatic light control
sensor (IG)Ignition switch OFFBelow 1 V
CLTB (*3) ± GND1
(B6±4 ± B6±6)R±G ± W±BAutomatic light control
sensor (IG)Ignition switch ON10 to 14 V
BZR ± GND1
(B7±15 ± B6±6)LG ± W±BWireless door lock
buzzer signalBuzzer does not soundBelow 1 V
BZR ± GND1
(B7±15 ± B6±6)LG ± W±BWireless door lock
buzzer signalBuzzer sounds10 to 14 V
RLD ± GND1
(B7±26 ± B6±6)L ± W±BPower window control
(Rear LH (DOWN))Ignition switch ONBelow 1 V
RLD ± GND1
(B7±26 ± B6±6)L ± W±BPower window control
(Rear LH (DOWN))Ignition switch ON,
Rear left power window DOWN
operation
10 to 14 V
RLU ± GND1
(B7±25 ± B6±6)G±R ± W±BPower window control
(Rear LH (UP))Ignition switch ONBelow 1 V
RLU ± GND1
(B7±25 ± B6±6)G±R ± W±BPower window control
(Rear LH (UP))Ignition switch ON,
Rear left power window UP op-
eration
10 to 14 V
RRD ± GND1
(B5±20 ± B6±6)L ± W±BPower window control
(Rear RH (DOWN))Ignition switch ONBelow 1 V
RRD ± GND1
(B5±20 ± B6±6)L ± W±BPower window control
(Rear RH (DOWN))Ignition switch ON,
Rear right power window DOWN
operation
10 to 14 V
RRU ± GND1
(B5±19 ± B6±6)G±Y ± W±BPower window control
(Rear RH (UP))Ignition switch ONBelow 1 V
RRU ± GND1
(B5±19 ± B6±6)G±Y ± W±BPower window control
(Rear RH (UP))Ignition switch ON,
Rear right power window UP op-
eration
10 to 14 V
HEAD ± GND1
(B6±9 ± B6±6)G±Y ± W±BLight control switch
(HEAD)Light control switch HEADBelow 1 V
HEAD ± GND1
(B6±9 ± B6±6)G±Y ± W±BLight control switch
(HEAD)Light control switch OFF or TAIL10 to 14 V
PKB ± GND1
(B5±3 ± B6±6)LG±R ± W±BParking brake switch
signalIgnition switch ON, Parking brake
appliedBelow 1 V
PKB ± GND1
(B5±3 ± B6±6)LG±R ± W±BParking brake switch
signalIgnition switch ON, Parking brake
not applied10 to 14 V
GSWGR RAirbag sensor commu-Airbag sensor communicationGSW
(B6±16)GR±RAirbag sensor commu
nication signal
Airbag sensor communication
circuit±
OBD2
(B5±2)G±RDiagnosis signalDLC3 communication circuit±
FFOG ± GND1
(B6±13 ± B6±6)G±B ± W±BFog light switch signalHeadlight dimmer switch LOW,
Fog light switch OFFBelow 1 V

DID99±01
DI±1694
± DIAGNOSTICSBODY CONTROL SYSTEM
1888 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the hand±held tester, you can read the values of the switches,
sensors, actuators and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting
is one of the methods to shorten labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on the tester, read the ºDATA LISTº.
BODY ECU:
ItemMeasurement Item/Display
(Range)Normal ConditionDiagnostic Note
KEY UNLK WRN SWKey unlock warning switch/ON or
OFFON: Key is in ignition key cylinder
OFF: No key is in ignition key cyl-
inder
±
ACC SWACC switch/ON or OFFON: Ignition switch ACC
OFF: Ignition switch OFF±
IG SWIG switch/ON or OFFON: Ignition switch ON
OFF: Ignition switch OFF±
PARKING BRAKE SWParking brake switch/ON or OFF
ON:
Parking brake pedal depressed
(ON)
OFF:
Parking brake released (OFF)
±
HOOD COURTSY SWHood courtesy switch/ON or OFF
ON: Engine hood OPEN
(Hood courtesy switch ON)
OFF: Engine hood CLOSED
(Hood courtesy switch OFF)
±
D DOR CTY SWDriver door courtesy light switch/
ON or OFFON: Driver door is opened
OFF: Driver door is closed±
P DOR CTY SWFront passenger door courtesy
light switch/ON or OFF
ON: Front passenger door is
opened
OFF: Front passenger door is
closed
±
Rr DOR CTY SWRear passenger door courtesy
light switch/ON or OFF
ON: Rear passenger door is
opened
OFF: Rear passenger door is
closed
±
MIRR SEL SW RRemote control mirror switch pas-
senger side/ON or OFF
ON: Remote control mirror switch
passenger side is selected
OFF: Remote control mirror switch
passenger side is not selected
±
MIRR SEL SW LRemote control mirror switch driv-
er side/ON or OFF
ON: Remote control mirror switch
driver side is selected
OFF: Remote control mirror switch
driver side is not selected
±
MIRR POS SW RRemote control mirror switch R
position/ON or OFF
ON: Remote control mirror switch
R position is selected
OFF: Remote control mirror switch
R position is not selected
±